Extron XTP DTP 24 Manual

Extron Ikke kategoriseret XTP DTP 24

Læs gratis den danske manual til Extron XTP DTP 24 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Extron XTP DTP 24, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1. Optional: Slide a strain relief or heat shrink

over the cable. The strain relief and heat shrink

are not included.

2. Make a circular score around the cable jacket

at approximately 1.25 inches (31.8mm) from

the end of the cable. Use the rip cord to

remove the jacket, then cut the rip cord.

3. Remove the foil and mylar shielding (if present)

from the end of the cable.

4. Turn the cable over and fold and atten the

braid against the bottom of the cable jacket for

grounding purposes (see note in step 11).

NOTE: In the gure to the right, the cable is

viewed from beneath, so the wires are in

reverse order.

5. Separate and untwist the four exposed twisted

pair wires and trim (but do not strip) the wires

to 0.8inch (20.3 mm).

6. Arrange and lay at the eight wires in the

correct order to comply with the TIA/EIA 568B

wiring standard (see the table at right).

NOTE: Plenum cable does not have a

stripe on the white conductor.

XTP DTP 24 Plug Kit for XTP DTP 24 Cable with CTU 45

The Extron Shielded XTP DTP 24 RJ-45 Plug kit terminates XTP DTP 24 shielded twisted pair

cable. The plug can accommodate 22 AWG to 28 AWG solid or stranded wires. The insulated

conductor diameter must be in the range of 0.044 to 0.048inch.

The following tools are required to complete a fully shielded cable assembly:

This guide provides instructions for completing a fully shielded cable assembly. To terminate

XTP DTP 24 shielded twisted pair cable, follow these steps:

Ripcord

Foil Shield

Braid Shield

1.25"

Fold Back Braid

1 2 3 4 5 6 7 8

0.80"

Wire Cutter/Stripper RJ-45 Tester

CTU 45

Termination Tool

123 456 78

Pi n

White/Bl ue

T 568B

Blue

White/Or ange

Orang e

White/Gr een

Green

White/Br own

Brown

0.3 "

0.6 "

www.e xtr on.c o m33-2522-01 A

T568B Wiring

White/Blue

T568B

Wire Colors

Blue

White/Orange

Orange

White/Green

Green

White/Brown

Brown

68-1813-01

Rev. F

07 14

Extron USA Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517

Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001

7. Feed the individual wires, in the correct order

(see table on the previous page), through the

open front face of the plastic guide and out

through the individual holes at the other side.

The rear of the guide should be seated against

the end of the jacket and braid.

8. Cut the wires to 0.6 inch (15.2 mm) as shown

at right.

9. Push the guide up, leaving 0.3 inch of the

wires exposed above the guide (see image at

right).

10. Insert the guide and wires into the RJ-45

connector, making sure the wires pass the

crimping teeth of the connector.

NOTE: Ensure the wires are in the correct

order (see table on the previous page)

and the bottom of the connector is next

to the braid shield that was folded under

the cable in step 4.

11. Insert the connector into the termination tool

and crimp it to secure the connector to the

cable. Be sure to insert the connector properly,

with the pins on top (see image at right).

NOTES:

• The CTU 45 tool crimps the front of

the connector, the jacket, and the

strain relief.

• To ensure correct grounding

throughout the cable, the braid shield

(folded back in step 4) must make

contact with the shielded RJ-45

connector on both ends of the cable.

12. If a strain relief is present, slide it forward to

cover the cable and the rst 0.4inch

(10.2 mm) of the RJ-45 connector.

13. Test both ends of the cable for conductivity.

NOTE: If there is a need to re-terminate the

cable, cut off the terminated end of the

cable and repeat steps 2 through 12.

Guide

Heat Shrink bing/Tu

Strain Relief (optional)

0.6"

0.3"

Ensu conductors are seatedre

properly under contacts.

Insert with pins on top.

Front

NOTE:

Produkt Specifikationer

Mærke:	Extron
Kategori:	Ikke kategoriseret
Model:	XTP DTP 24
Produktfarve:	Blå
Kabellængde:	304.8 m
Harmoniseret systemkode (HS):	84733080
Stik 1:	Ingen
Stik 2:	Ingen
Stik 1 køn:	Ingen
Stik 2 køn:	Ingen
AWG-ledningsstørrelse:	24
Kabelafskærmning:	SF/UTP (S-FTP)