Extron XTP DTP 24 Punch Down Jack Manual

Extron Ikke kategoriseret XTP DTP 24 Punch Down Jack

Læs gratis den danske manual til Extron XTP DTP 24 Punch Down Jack (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Extron XTP DTP 24 Punch Down Jack, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
XTP DTP 24 Punch Down Jack • Setup Guide
The following tools are required to terminate the shielded XTP DTP 24 punch down connector:
Follow these instructions to terminate the connector:
1. Slide the rear case of the connector over the
cable. Push the case back at least 3 inches
(76 mm) to make room for the termination of the
cable.
2. Remove about 2 inches (50 mm) of the cable
jacket.
3. Fold down the braid over the cable jacket.
Remove the foil and mylar shielding (if present).
4. Note the color codes and pin numbers on the
sides of the connector. Follow the color code in
the table at right to wire the connector.
5. Untwist the wire pairs and hold the end of the
stripped cable jacket close to the back of the
connector. The length of the exposed wires in the
connector should not exceed 0.6 inch (see image
at right).
ATTENTION: Failure to position the
cable properly may result in crosstalk and
improper termination.
Slide Rear Case
over Cable
1
2Strip Jacket 2"
Fold Braid over Jacket
and Remove Foil
3
4Color-coded Label
w/ Pin Number
Color Code B
IDC Slots
2 1 4 5
A
B
5
6
Distance Between
Cable and Connector
0.6"
IDC
Position
T568B Wiring
IDC Numbers & Color Codes
White/Blue
T568B
Wi Colorsre
5
4
1
2
3
6
7
8
Blue
White/Orange
Orange
White/Green
Green
White/Brown
Brown
110-Style Punchdown Tool
(Provided)
Wire Cutter RJ-45 Tester
6. Position each wire into its respective IDC slot. Insert
the wires just far enough to hold them in the IDC slots.
7. Use the 110-style punchdown tool to push down
each wire into the IDC slot. Push the punchdown
tool until the wire is rmly secured at the bottom
of the slot.
8. Trim the excess wire ush with the body of the
connector.
9. Tighten the grounding tie around the braid.
10. Remove the excess braid at the grounding tie.
11. Place the plastic cover over the termination wires
for secure connection and added strain relief.
12. Push the rear case forward until it clicks into
position over the terminated connector.
13. Test both ends of the cable for conductivity.
NOTE: If there is a need to re-terminate the
connector, insert a tweeker on the bottom of the
rear case and slide it back to access the wires.
NOTE: The wire retention mechanism in these
connectors is very secure. If a terminated cable
must be separated from its connector, separate
it one wire at a time. 68-2370-50
Rev. C
04 13
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
7110 - Style
Punchdown olTo
8
Trim Excess
Wire
9
Grounding
Tie
2 1 4 5
A
B
11
10
Plastic
cover
12
Rear Case

Produkt Specifikationer

Mærke: Extron
Kategori: Ikke kategoriseret
Model: XTP DTP 24 Punch Down Jack

Har du brug for hjælp?

Hvis du har brug for hjælp til Extron XTP DTP 24 Punch Down Jack stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Extron Manualer

Extron

Extron HC 403 Manual

16 August 2025
Extron

Extron MLC 64 RS VC D Manual

5 August 2025
Extron

Extron MGP 641 xi 5K Manual

30 Juli 2025
Extron

Extron MLC 62 RS D Manual

30 Juli 2025
Extron

Extron DTP T UWP 4K 332 D Manual

22 Juli 2025
Extron

Extron DA HD 4K PLUS Manual

21 Juli 2025
Extron

Extron IN2004 Manual

21 Juli 2025
Extron

Extron FOX3 T 311 Manual

21 Juli 2025
Extron

Extron AAP 104 Manual

20 Juli 2025
Extron

Extron DTP T DSW 4K 233 Manual

20 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Cres Cor

Cres Cor H137WSUA5D Manual

20 August 2025
Moulinex

Moulinex Pulseo LM17GD Manual

20 August 2025
Tefal

Tefal EasyGrill BG1303 Manual

20 August 2025
Tenda

Tenda U2 Manual

20 August 2025
Tefal

Tefal Ultraglide Plus FV5841 Manual

20 August 2025
Tefal

Tefal I-Coach Touch QB950D Manual

20 August 2025
BEKO

BEKO BDIN38551P Manual

20 August 2025
BEKO

BEKO FSE52135DCRSN Manual

20 August 2025
Karma

Karma PRJ 5000 Manual

20 August 2025
Aqua-Vu

Aqua-Vu Micro Stealth 4.3 Manual

20 August 2025