
I
I
I
IM
M
M
MP
P
P
PO
O
O
ORT
RT
RT
RTA
A
A
AN
N
N
NT:
T:
T:
T:
Go to www.extron.com for the
complete user guide, installation
instructions, and specifications.
ZipClip400/ZipCaddy400 • Installation Guide
Figure 1. Front and Side View of the
The ZipClip400/ZipCaddy400 mounting kit is a plastic mounting kit allowing
1/2, 1/4, and 1/8 rack width, 3 inches (76 mm) or select 6 inches (152 mm) deep
Extron enclosures and select small form factor PCs to be securely and easily
mounted to various surfaces, such as under a table, on a rack rail system (side or
The ZipCaddy400 has two sides with a step groove to allow the edges to snap
into the ZipClip400. The ZipCaddy400 disengages with a press of the lever tab
• A 1/2 rack product takes up the entire ZipCaddy400 plate. Multiple 1/4
and 1/8 products fit onto the ZipCaddy400 side-by-side.
• Included cable ties are used to secure cables to the ZipCaddy400 (see
• (4) Product mounting #4-40 screws
• (4) ZipClip mounting #12 wood screws
Installing Device Onto a Rack
1
LR
5A 6A
XTP
RS-2
32 IR
Tx Rx Tx Rx
G
Tx
Rx G
RESET
XTP
DTP
XTP
DTP
+48V
MIC/LINE
113
24
2
3
4
LAN 2
LAN 1
LAN 3
DTP
HDBT
5 7 8
4
CLASS 2 WIRING
8 /
OV ER TP
REMOTE
SIG
LINK
IN
SI
G
L
IN
K
IN
AUDIO INPUTS
AUDIO OUTPUTS
AMP OUTPUT
INPUTS
RS-232 IR
Tx Rx Tx Rx
G
RS-232 IR
T
xRx T
x Rx
G
XTP
DTP
XTP
DTP
910
OVER TP
S
I
G
LI N
K
IN
SIG LINK
IN
RS-232 IR
Tx Rx Tx RxG
1
LR
1
LR
3
LR
3
L R
5
L R
2
L R
4
L R
2
L R
4
L R
6
LR
S
I
G
LI
NK
OUT
6B 6
RS-
232 IR
x Rx Tx R x
XTP
S/PDIF
OUT
DTP HDBT
G
RS-232 IR
x Rx T
x Rx
G
OVER TP
XTP
DTP
HDBT
SIG LINK
OUT
SIG LINK
OUT
7 8
RS-232 IR
Tx Rx Tx Rx
XTP
DTP
HDBT
G
RS-232 IR
Tx Rx Tx Rx
G
OVER TP
CONTROL S
IN
OUT O)
VIDEO S VIDEO
TEL LINE
HDMI AC IN
AC OUT
A
AUDIO 3
OUT
LR
B O
RGB INP
AUDIO
V DEO
HV
A
AUDIO
LRB
A
LRB
ISOGC SYNC
50/60 Hz
B
50/60 H z
CONTROL S
IN
OUT (MONO)
LR
AUDIO VIDEO S VIDEO CH 3
CH 4
VHF/UHF
VHF(SAT)/UHF
IN
OUT
TEL LINE
AC IN
AC OUT
A
RF REMOTE
AUDIO 3
OUT
LR
e
Figure 2. Installation onto the Back of a Rack.
1. Install the ZipClip400 to the rack (see figure2,
2. Secure the rack product, products, or small PC to the ZipCaddy400
with the provided #4-40 product mounting screws (
3. To install, insert the ZipCaddy400 onto the ZipClip 400 and click
To remove, press down on the ZipClip400 tab.