FERM FRJ-2000HL Manual

FERM Donkraft FRJ-2000HL

Læs gratis den danske manual til FERM FRJ-2000HL (8 sider) i kategorien Donkraft. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 2 anmeldelser. Har du et spørgsmål om FERM FRJ-2000HL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Ferm BV

●

P.O. Box 134

●

8280 AC Genemuiden-NL

●

Web: www.ferm.com 0305/14

USER’S MANUAL

GEBRAUCHSANLEITUNG

GEBRUIKSAANWIJZING

MODE D’EMPLOI

BRUKSANVISNING

KÄYTTÖOHJE

BRUKSANVISNING

BRUGER VEJLEDNING

Voor:

Art.nr. 340290

Ferm FRJ-2000HL

High lifting jack

Hochheber

Hooglichter

Cric de garage grand levage

Garagedomkraft

Hallinosturi

Garasjejekk

Donkraft

Ferm 15

REF.NR. DESCRIPTION FERM NR.

16 SPRING 405223

28 SPRING (RIGHT) 405233

28 SPRING (LEFT) 405245

64 TENSION SPRING 405237

-OVERHAUL SET 405238

SPARE PARTS FOR FRJ-2000HL

Product: Ferm high lifting jack.

Type FRJ-2000HL, art. nr. 340290

Ferm B.V., Genemuiden, The Netherlands.

SERIAL NUMBER

The serial number on the machine consists of the

following elements.

Serial nr.

CAREFULLY READ THE INSTRUCTIONS

BEFORE YOU USE THE HIGH LIFT!

1. SPECIAL SAFETY RULES

Non-observance of the following instruc-

tions can cause personal injuries and/or

damage to the vehicle.

1. Place the saddle of the high lifting jack only in the

spot designed for this purpose. For the relevant lif-

ting points please refer to your car instructions.

2. The maximum load indicated on the jack must

never be exceeded.

3. The jack must be used as a lifting device only.

4. Always place the jack on a hard and level surface.

5. Always protect the car from rolling away. Before

jacking up the car, place chocks behind and in front

of the wheels remaining on the ground, if necessa-

ry. Put the car in first gear or put on the handbrake

to further block the car.

6. Make sure to place the jack in such a way that your

hand is not underneath the car when jacking it up.

7. Make sure the jack is horizontal.

8. For your own safety, before working or crawling

underneath the car jack up the car and support the

shafts.

9. Before using the shaft supports make sure they are

in good condition.

2. OPERATION

The hand lever, handle and foot lever first have to be

attached before lifting operations can be started.

1. ATTACHMENT OF THE LEVERS

The handles are simple to attach to the hand lever.

Place the levers in the appropriate openings and fix

them by means of the bolt and nut. Make sure that the

hand lever is inserted as far as possible into the ope-

ning. Then tighten the bolt and nut to enable the high

lift to be moved using the hand lever.

2. LIFTING

Move the high lift into the correct position (as indica-

ted on the vehicle by the manufacturer). Turn the hand

lever knob as far as possible to the right in a clockwise

direction. The high lift is now ready to lift. Place the

high lift in a horizontal position on a flat surface and

start to pump by moving the lever up and down. You

can also use your foot to pump the foot lever.

3. AXLE SUPPORTS

Once the vehicle has been raised into position, axle

supports have to be put into place. Allow the vehicle

to sink down by turning the lever to the left until it is

resting on the axle supports. There must be absolutely

no work carried out under any vehicle which is only

supported by the high lift.

4. LOWERING

After work has been completed, the vehicle can be jac-

ked up again until it is free of the axle supports. These can

then be removed. Turn the knob on the lever to the left

and the vehicle will be lowered. The further the lever is

turned to the left, the faster the vehicle will be lowered.

3. MAINTENANCE

REGULAR MAINTENANCE OF YOUR HIGH LIF-

TING JACK PREVENTS PROBLEMS.

1. Once a month the wheels, shafts and piston rods

should be lubricated with lubricating oil and grease

on the pivots of the lifting rods.

2. The tank containing hydraulic oil is a closed tank

which usually does not require maintenance.

When frequently used, but at least on ce a year,

ORDER NUMBER/YEAR OF CONSTRUCTION

English

2 Ferm

kg.

2000 kg

55 kg

min.140 mm

max. 800 mm

Produkt Specifikationer

Mærke:	FERM
Kategori:	Donkraft
Model:	FRJ-2000HL

Har du brug for hjælp?

Hvis du har brug for hjælp til FERM FRJ-2000HL stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Donkraft FERM Manualer

FERM FRJ-2000HL Manual

20 September 2025

Donkraft Manualer

Nyeste Donkraft Manualer

WilTec 51157 Manual

31 August 2025

WilTec 50800 Manual

31 August 2025

Einhell HM 122 Manual

21 August 2025

Guede 2T Manual

31 Juli 2025

Guede 15T Manual

31 Juli 2025

Guede 3T Manual

30 Juli 2025

NEO Tools 11-732 Manual

8 Juli 2025

NEO Tools 11-737 Manual

8 Juli 2025

MSW -HR-680 Manual

24 Juni 2025

MSW -OWH-3000 Manual

17 Juni 2025