Festo ASI-4DI3DO-M12X2-5POL-Z Manual

Festo Ikke kategoriseret ASI-4DI3DO-M12X2-5POL-Z

Læs gratis den danske manual til Festo ASI-4DI3DO-M12X2-5POL-Z (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Festo ASI-4DI3DO-M12X2-5POL-Z, eller vil du spørge andre brugere om produktet?

Side 1/2
Warnung, Warning, Varning. . . . . . . . . . . . . . . . . . . . . . . . .
de Vor Installations- und Wartungsarbeiten Spannungs-
versorgung ausschalten!
Nur PELV-Netzteile nach IEC/DIN EN 60204-1 oder
Class 2 Circuits verwenden!
en Switch off the power supply before carrying out instal-
lation and maintenance work!
Use only PELV power units as per IEC/DIN EN 60204-1
or Class 2 Circuits!
sv Innan installations- och underhållsarbete påbörjas
ska spänningsmatningen kopplas från!
Använd endast PELV-nätdelar enligt IEC/DIN EN
60204-1 eller Class 2 Circuits!
Industrial Control Equipment
Only for use in Class 2 Circuits
This device is intended to be used with a Class 2 power
source or Class 2 transformer in accordance with UL 1310 or
UL 1585.
As an alternative a LV/C (Limited Voltage/Current) power
source with one of the following properties can be used:
This device shall be used with a suitable isolating source
such that the maximum open circuit voltage potential
available to the product is not more than 24 Vdc and the
current is limited to a value not exceeding 8 amperes
measured after 1 minute of operation.
This device shall be used with a suitable isolating source
in conjunction with a fuse in accordance with UL 248. The
fuse shall be rated max. 4 A and be installed in the 24 Vdc
power supply to the device in order to limit the available
current.
Field installed conductors for the device shall be segrega-
ted from field and factory installed conductors and uninsu-
lated live parts of other circuits operating at over 150 V to
ground so that a minimum permanent 2 inch (50.8 mm)
separation is maintained, unless the field wiring conductors
have been provided with recognized insulating material
which has an equal or higher voltage rating than the other
circuit involved.
Protection class: NEMA Type 1, 2, 3R, 4, 4X, 12, 13.
AS-i-Modul de. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Funktion
Das AS-i-Modul ASI-4DI3DO-M12X2-5POL-Z dient zum An-
schluss von bis zu 4 Sensoren (z. B. Näherungsschalter, Licht-
schranken) und 3 elektrischen Verbrauchern an das AS-Inter-
face.
2 Anwendung
Das Modul ist nur folgendermaßen zu benutzen:
im Originalzustand, ohne eigenmächtige Veränderungen,
in technisch einwandfreiem Zustand.
3 Einbau und Inbetriebnahme
Warnung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heisse Oberfläche! Kurzschluss bzw. Überlast kann zu Tem-
peraturen > 100 °C führen.
Befestigen Sie das Modul nur auf hitzebesndigem
Untergrund!
Hinweis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Der Einbau und die Inbetriebnahme darf nur gemäß der
Bedienungsanleitung und von qualifiziertem Fachpersonal
erfolgen.
Eingänge nicht mit externer Versorgungsspannung verbin-
den (galvanisch gekoppelt mit AS-i)!
Zum Betrieb sind die angegebenen Grenzwerte der techni-
schen Daten einzuhalten.
Das Modul unterstützt A/B-Betrieb gemäß AS-i-Spezifika-
tion 2.11 oder höher.
4 Technische Daten
Typ ASI-4DI3DO-M12X2-5POL-Z
AS-i Busspannung 26,5 ... 31,6 V DC
Lastspannung
– allgemein
geß UL
24 V DC ± 25 %
(siehe Technische Daten elektri-
scher Verbraucher)
24 V DC, Class 2
Strom AS-i Bus/AUX max. 4 A/Pin
AS-i-Profil (IO.ID.ID2) S-7.A.2
AS-i Gesamtstromaufnahme max. 250 mA
Digitale Ein-/Ausgänge 4/3, PNP
Eingangsvergerungszeit typ. 3 ms
Sensorstrom pro Eingang
allgemein/ gemäß UL max. 240 mA / max. 200 mA
Sensorstrom pro Modul
allgemein/ gemäß UL max. 240 mA / max. 200 mA
Ausgangsstrom
allgemein/ gemäß UL max. 1 A / max. 0,5 A
Parallelschalten ja
Kurzschlussschutz ja, thermisch
Autom. Spannungswiederkehr ja
Zulässige Umgebungstempera-
tur
Betrieb / Lagerung -5 °C ... +50 °C / -20 °C ... +70 °C
Gewicht 165 g
AS-i module en....................................................
1 Function
The valve switching module serves for connecting up to 4
sensors (e.g. proximity switches, light barriers) and 3 electri-
cal consuming devices to the AS-interface.
2 Application
The module may only be used as follows:
in its original condition without modifications,
in technically faultless condition.
3 Installation and commissioning
Warning..................................................
Hot surface! Short circuit or overload can lead to tempera-
tures > 100 °C.
Fasten the module only on a heat-resistant base!
Please note.............................................
Fitting and commissioning must be carried out only in ac-
cordance with the operating instructions and only by quali-
fied personnel trained for this purpose.
Inputs must not be fed with external supply voltages (elec-
trically coupled to AS-i).
The specified maximum limit values must be observed
during operation.
The module supports A/B operation as per AS-i specifica-
tion 2.11 or higher.
4 Technical specifications
Type ASI-4DI3DO-M12X2-5POL-Z
AS-i bus voltage 26.5 ... 31.6 V DC
Load voltage
– general
as per UL
24 V DC ± 25 %
(see technical specifications of
electrical consumers)
24 V DC, Class 2
Current AS-i bus/AUX max. 4 A/Pin
AS-i-profile (IO.ID.ID2) S-7.A.2
AS-i total current consumption max. 250 mA
Digital inputs/outputs 4/3, PNP
Input delay time typ. 3 ms
Sensor current per input
general / as per UL max. 240 mA / max. 200 mA
Sensor current per module
general / as per UL max. 240 mA / max. 200 mA
Output current
general / as per UL max. 1 A / max. 0.5 A
Parallel switching yes
Short-circuit protection yes, thermal
Autom. voltage recovery yes
Permitted ambient temperature
operation / storage
-5 °C ... +50 °C / -20 °C ... +70 °C
Weight 165 g
AS-i modul sv.......................................................
1 Funktion
Modulen ventilanslutning är avsedd för anslutning av upp till
4 givare (t.ex.. cylindergivare, fotoceller) och 3 elektriska
förbrukare till AS-Interface.
2 Användning
Modulen får endast användas enligt följande:
i originalskick, utan egna förändringar,
i tekniskt felfritt tillstånd.
3 Montering och Idrifttagande
Varning..................................................
Varm yta! Kortslutning resp. överbelastning kan leda till
temperaturer > 100 °C.
Fäst endast modulen på ett värmebeständigt underlag!
Notera....................................................
Montering och idrifttagning får endast utföras av berig
personal enligt bruksanvisningen.
Anslut inte ingångarna med extern matningsspänning (gal-
vaniskt kopplad med AS-i)!
Vid drift ska de gränsvärden som anges under Tekniska
data följas.
Modulen stöder A/B-drift enligt AS-i-specifikation 2.11
eller högre.
4 Tekniska data
Typ ASI-4DI3DO-M12X2-5POL-Z
AS-i bussnning 26,5 ... 31,6 V DC
Matningsspänning
– allmänt
enligt UL
24 V DC ± 25 %
(se tekniska data för elektriska
förbrukare)
24 V DC, Class 2
Ström AS-i-buss/AUX max. 4 A/Pin
AS-i-profil (IO.ID.ID2) S-7.A.2
AS-i total strömrbrukning max. 250 mA
Digitala in-/utgångar 4/3, PNP
Ingångsfördröjningstid typ. 3 ms
Givarström per ingång
allmänt / enligt UL max. 240 mA / max. 200 mA
Givarström per modul
allmänt / enligt UL max. 240 mA / max. 200 mA
Utgångsström
allmänt / enligt UL max. 1 A / max. 0,5 A
Parallellkoppling ja
Kortslutningsskydd ja, termiskt
Autom. snningstillkoppling ja
Tiltenomgivningstemperatur
Drift / Förvaring
-5 °C ... +50 °C / -20 °C ... +70 °C
Vikt 165 g
Einbauhinweise / Mechanical connection / Mekaniska anslutningar Elektrischer Anschluss / Electrical connection / El-anslutningar
Ø 4,3 mm
max. 2 ± 0,5 Nm
he/height/Höjd: ca. 34,5 mm
M12: 0,6 Nm ± 0,1Nm
AS-i Anschluss (M12)/
AS-i connection (M12)/
AS-i-anslutning (M12):
AS-i In/Out:
Pin 1 = AS-i +
Pin 2 = 0 V*)
Pin 3 = AS-i
Pin 4 = 24 V DC ±25%*)
Pin 5 = n.c.
*) Power load
AS-i In
AS-i Out
Anschluss Funktionserde (FE)
Functional earth connection (FE)
Funktionsjordanslutning (FE)
4 DI
(Inputs, M12)
3 DO
(Outputs, M12)
Eingänge / Inputs / Ingångar:
0, 1: Pin 1 = +24 VDC 2, 3: Pin 1 = +24 VDC
Pin 2 = Ix+1 Pin 2 = Ix+3
Pin 3 = 0 V Pin 3 = 0 V
Pin 4 = Ix+0 Pin 4 = Ix+2
Pin 5 = FE Pin 5 = FE
Ausgänge / Outputs / Utgångar:
0, 1: Pin 1 = n.c. 2: Pin 1 = n.c.
Pin 2 = Ox+1 Pin 2 = n.c.
Pin 3 = 0 V Pin 3 = 0 V
Pin 4 = Ox Pin 4 = Ox+2
Pin 5 = FE Pin 5 = FE
Adressierung / Addressing / Adressering LED-Anzeige / LED display / LED-indikering
ASI-PRG-ADR
KASI-ADR
NEBU-M12G5-F-0,2-M12G4
de AS-i-Adresse (Werkseinstellung) #0a
Adressierbereich #1a,#1b ... #31a,#31b
Anzahl Adressierzyklen beliebig
en AS-i-Address (Default) #0a
address range #1a,#1b ... #31a,#31b
numbers of address cycles as desired
sv AS-i-adress (förinsllt) #0a
Adressfält #1a,#1b ... #31a,#31b
Antal adresscykler valfritt
LED : Power AS-i (grün/green/grön)1
an/on/till
AS-Interface-Spannung vorhanden
AS-Interface voltage applied
AS-Interface spänning finns
aus/out/från
Keine AS-Interface-Spannung am Bus
No AS-Interface voltage on bus
Ingen AS-Interface spänning på bussen
LED 2: Fault (rot/red/röd)
aus/out/från
Kein Kurzschluss/Überlast
No short circuit/overload
Ingen kortslutningverbelastning
blinkt/flashes/binkar
Kurzschluss/Überlast
Short circuit/overload
Kortslutningverbelastade
an/on/till
AS-Interface-Adresse nicht eingestellt (gleich Null),
Ausfall der Bus-Kommunikation (Watchdog abgelaufen)
AS-Interface address not set (equals zero),
Failure of bus communication (watchdog expired)
AS-Interface adress ej inställd (lika med noll),
Avbrott busskommunikationen (watchdog överskriden)
LED : Aux (grün/green/grön)3
an/on/till
Lastspannung vorhanden
Auxiliary voltage applied
Matningsspänning finns
aus/out/från
Lastspannung fehlt
Auxiliary voltage not applied
Matningsspänning fattas
LED 4: Status Eingänge (grün/green/grön)/
LED 5: Status Ausgänge (gelb/yellow/gul)
an/on/till
1-Signal an Ein-/Ausgang
1-signal at input/output
1-signal på in-/utgång
aus/out/från
0-Signal an Ein-/Ausgang
0-signal at input/output
0-signal på in-/utgång
3
12
5
4
4
5
ASI-4DI3DO-M12X2-5POL-Z
Bedienungsanleitung
Operating instructions
Bruksanvisning
Original: de
Festo SE & Co. KG
Postfach
D-73726 Esslingen
Phone:
+49/711/347-0
www.festo.com
0508NH 694 049
IND. CONT. EQ. 29TS
Atención, Attention, Attenzione. . . . . . . . . . . . . . . . . . . .
es Desconectar la fuente de alimentacn antes de reali-
zar trabajos de instalacn y mantenimiento! Utilizar
sólo fuentes PELV según IEC/DIN EN 60204-1 o
Class 2 Circuits!
fr Avant toute intervention dinstallation ou de mainte-
nance, couper lalimentation électrique ! Utiliser exc-
lusivement des blocs d’alimentation TBT conformes à
la norme CEI/DIN EN 60204-1 ou Circuits de Classe 2 !
it Prima di iniziare i lavori di installazione e di manuten-
zione scollegare l’alimentazione elettrica! Utilizzare
solo alimentatori PELV secondo IEC/DIN EN 60204-1
o Class 2 Circuits!
Industrial Control Equipment
Only for use in Class 2 Circuits
This device is intended to be used with a Class 2 power
source or Class 2 transformer in accordance with UL 1310 or
UL 1585.
As an alternative a LV/C (Limited Voltage/Current) power
source with one of the following properties can be used:
This device shall be used with a suitable isolating source
such that the maximum open circuit voltage potential
available to the product is not more than 24 Vdc and the
current is limited to a value not exceeding 8 amperes
measured after 1 minute of operation.
This device shall be used with a suitable isolating source
in conjunction with a fuse in accordance with UL 248. The
fuse shall be rated max. 4 A and be installed in the 24 Vdc
power supply to the device in order to limit the available
current.
Field installed conductors for the device shall be segrega-
ted from field and factory installed conductors and uninsu-
lated live parts of other circuits operating at over 150 V to
ground so that a minimum permanent 2 inch (50.8 mm)
separation is maintained, unless the field wiring conductors
have been provided with recognized insulating material
which has an equal or higher voltage rating than the other
circuit involved.
Protection class: NEMA Type 1, 2, 3R, 4, 4X, 12, 13.
Módulo AS-i es. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Función
El módulo conmutador de lvulas sirve para conectar hasta
4 sensores (p.ej. detectores de proximidad, barreras de luz) y
3 dispositivos consumidores ectricosal AS-interface.
2 Aplicación
El módulo sólo debe utilizarse como sigue:
en sus condiciones originales sin modificaciones,
en condiciones técnicas sin fallos.
3 Montaje y puesta en funcionamiento
Atención. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Superficie caliente! Cortocircuitos o sobrecargas pueden
producir temperaturas de > 100 °C.
Fije el módulo sólo sobre una base resistente al calor!
Por favor, observar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
El montaje y la puesta en funcionamiento debe llevarse a
cabo únicamente de acuerdo con las instrucciones de fun-
cionamiento y por personas cualificado y formadas para
ello.
Las entradas no deben alimentarse con tensiones externas
(eléctricamente acoplado a AS-i).
Durante el funcionamiento deben observarse los valores
mite máximos especificados.
El módulo soporta el funcionamiento A/B según especifi-
cacn AS-i 2.11 o superior.
4 Especificaciones técnicas
Tipo ASI-4DI3DO-M12X2-5POL-Z
Tensión del bus AS-i 26,5 ... 31,6 V DC
Tensión de carga
– general
según UL
24 V DC ± 25 %
(ver las especificaciones cnicas
de los consumidores eléctricos)
24 V DC, Class 2
Corriente bus AS-i/AUX max. 4 A/Pin
Profil AS-i (IO.ID.ID2) S-7.A.2
Consumo total de corriente AS-i max. 250 mA
Entradas/salidas digitales 4/3, PNP
Tiempo de retardo de entrada tip. 3 ms
Corriente de sensor por entrada
general / según UL max. 240 mA / max. 200 mA
Corriente de sensor por módulo
general / según UL max. 240 mA / max. 200 mA
Corriente máxima de salida
general / según UL max. 1 A / max. 0,5 A
Conmutación en paralelo si
Protección ante cortocircuito si, térmica
Recuperación de tensión au-
totica
si
Temperatura ambiente permitida
funcionamiento / almacena-
miento -5 °C ... +50 °C / -20 °C ... +70 °C
Peso 165 g
ModuleAS-i fr..................................
1 Fonction
Module interface de distributeur sert à raccorder jusqu’à 4
capteurs (p. ex. des capteurs de proximité, des cellules
photolectriques) et 3 consommateurs électriques sur l’in-
terface AS.
2 Application
Le module doit être utilisé exclusivement de la façon sui-
vante :
dans son état d’origine, sans modifications non autorisées,
dans un état technique correct.
3 Montage et mise en service
Avertissement..........................................
Surface chaude ! Un court-circuit ou une surcharge peut
provoquer des températures > 100 °C.
Fixer le module uniquement sur une surface résistant à
la chaleur !
Note......................................................
Le montage et la mise en service doivent être effectués
uniquement conformément aux instructions d’utilisation et
par du personnel agréé.
Ne pas relier les entrées à une alimentation électrique
externe (couplage galvanique avec AS-i) !
Pendant le fonctionnement, veiller à respecter les valeurs
limites indiquées dans le chapitre Caractéristiques techni-
ques.
Le module supporte le mode A/B selon les scifications
AS-i 2.11 ou supérieures.
4 Caractéristiques techniques
Type ASI-4DI3DO-M12X2-5POL-Z
Tension du bus AS- i 26,5 ... 31,6 V DC
Tension d’alimentation
– généralement
selon UL
24 V DC ± 25 % (voir les ca-
racristiques techniques du
consommateur électrique)
24 V DC, Class 2
Courant bus AS-i/AUX max. 4 A/Pin
Profile AS-i (IO.ID.ID2) S-7.A.2
Consommation totale de courant
du module AS-i
max. 250 mA
Entrées/sorties TOR 4/3, PNP
Durée de temporisation des
entrées
3 ms val. type
Courant capteur par entrée
néralement / selon UL max. 240 mA / max. 200 mA
Courant capteur par module
néralement / selon UL max. 240 mA / max. 200 mA
Courant de sortie
néralement / selon UL max. 1 A / max. 0,5 A
Montage en parallèle oui
Protectioncontre les court-cir-
cuits
oui, thermique
Autom. Rétablissement de la ten-
sion
oui
Température ambiante adm
Fonctionnement /
Stockage -5 °C ... +50 °C / -20 °C ... +70 °C
Poids 165 g
ModuloAS-i it...................................
1 Funzionamento
Il modulo per connessione valvole viene utilizzato per colle-
gare fino a 4 sensori (ad es. finecorsa magnetici, fotocellule)
e 3 utenze elettriche allAS-Interface.
2 Utilizzo
Utilizzare il modulo solo nel modo seguente:
nello stato originale, senza apportare modifiche non auto-
rizzate,
in uno stato tecnicamente perfetto.
3 Montaggio e messa in servizio
Avvertenza..............................................
Superficie calda! Cortocircuito o sovraccarico possono
provocare temperature di > 100 °C.
Fissare il modulo su una superficie termoresistente!
Nota......................................................
Montaggio e messa in funzione devono essere effettuati
attenendosi alle istruzioni per l’uso e da personale specia-
lizzato autorizzato.
Non collegare gli ingressi con la tensione di alimentazione
esterna (accoppiata galvanicamente con AS-i)!
Per l’esercizio dei moduli osservare i valori limite riportati
nei dati tecnici.
Il modulo supporta il modo I/O secondo la specificazione
AS-i 2.11 o superiore.
4 Dati tecnici
Tipo ASI-4DI3DO-M12X2-5POL-Z
AS-i Busspannung 26,5 ... 31,6 V DC
Tensione di carico
caratteristiche generali
secondo UL
24 V DC ± 25 %
(vedi Dati tecnici delle utenze
elettriche)
24 V DC, Class 2
Corrente bus AS-i/AUX max. 4 A/Pin
Profilo AS-i (IO.ID.ID2) S-7.A.2
Assorbimento di corrente com-
plessivo AS-i
max. 250 mA
Ingressi/Uscite digitali 4/3, PNP
Tempo di ritardo d’ingresso tip. 3 ms
Corrente sensore per ingresso
allgemein/ gemäß UL max. 240 mA / max. 200 mA
Corrente sensore per modulo
allgemein/ gemäß UL max. 240 mA / max. 200 mA
Corrente di uscita
allgemein/ gemäß UL max. 1 A / max. 0,5 A
Collegabile in parallelo si
Protezione anticortocircuito si, termica
Boot-up della tensione si
Temperatura ambienteammissibi-
le
Esercizio / Magazzinaggio -5 °C ... +50 °C / -20 °C ... +70 °C
Peso 165 g
Conexión mecánica / Montage mécanique / Collegamento meccanico Conexión eléctrica / Raccordement électrique / Collegamento elettrico
Ø 4,3 mm
max. 2 ± 0,5 Nm
Alto /Hauteur/Altezza: ca. 34,5 mm
M12: 0,6 Nm ± 0,1Nm
Conexión AS-i (M12)
Connecteur AS-i (M12)
Connessione AS-i (M12):
AS-i In/Out:
Pin 1 = AS- i +
Pin 2 = 0 V*)
Pin 3 = AS- i
Pin 4 = 24 V DC ±25%*)
Pin 5 = n.c.
*) Power load
AS-i In
AS-i Out
Conexión de tierra functional (FE)
Borne de terre (FE)
Connessione funzionale di terra (FE)
4 DI
(Inputs, M12)
3 DO
(Outputs, M12)
Entradas/Entrées/Ingressi:
0, 1:Pin 1 = +24 VDC 2, 3: Pin 1 = +24 VDC
Pin 2 = Ix+1 Pin 2 = Ix+3
Pin 3 = 0 V Pin 3 = 0 V
Pin 4 = Ix+0 Pin 4 = Ix+2
Pin 5 = FE Pin 5 = FE
Salidas/Sorties/Uscite:
0, 1:Pin 1 = n.c. 2: Pin 1 = n.c.
Pin 2 = Ox+1 Pin 2 = n.c.
Pin 3 = 0 V Pin 3 = 0 V
Pin 4 = Ox Pin 4 = Ox+2
Pin 5 = FE Pin 5 = FE
Direccionamiento / Adressage/ Indirizzamento Indicator LED / Témoin LED / LED di segnalazione
ASI-PRG-ADR
KASI-ADR
NEBU-M12G5-F-0,2-M12G4
es Dirección AS-i (Predeterminado) #0a
margen de direcciones #1a,#1b ... #31a,#31b
mero de ciclos de direcciones indiferente
fr Adresse AS-i (réglage usine) #0a
Plage d’adressage #1a,#1b ... #31a,#31b
Nombre de cycles d’adressage indifférent
it Indirizzo AS-i (impostazione di fabbrica) #0a
Campo di indirizzamento #1a,#1b ... #31a,#31b
Numero dei cicli di indirizzamento qualsiasi
LED 1: Power AS-i (verde/verte/verde)
activado/allue/acceso
Tensión AS-Interface aplicada
Présence de tension AS-Interface
Tensione AS-Interface presente
apagado/éteinte/spendo
No hay tensión AS-Interface en el bus
Pas de tension AS-Interface sur le bus
Tensione AS-Interface non presente nel bus
LED 2: Fault (rojo/rouge/rosso)
apagado/éteinte/spendo
Sin cortocircuito / sobrecarga
Pas de court-circuit/surcharge
Nessun Cortocircuito/sovraccarico
parpadea/clignotante/lampeggiante
Cortocircuito/sobrecarga
Court-circuit/surcharge
Cortocircuito/sovraccario
activado/allue/acceso
Dirección AS-Interface no establecida (igual a cero),
Fallo en la comunicación del bus (watchdog expirado)
Adresse AS-Interface non définie (valeur nulle),
Coupure de la communication avec le bus (Watchdog écoulé)
Indirizzo AS-Interface non impostato (= 0),
Interruzione della comunicazione bus (watchdog scattato)
LED 3: Aux (verde/verte/verde)
activado/allue/acceso
Aplicada la tensión de carga
Tension d’alimentation psente
Tensione di carico presente
apagado/éteinte/spendo
No aplicada tensión de carga
Tension dalimentation absente
Tensione di carico assente
LED 4: Status Entradas/Entrées/Ingressi
(verde/verte/verde)/
LED 5: Status Salidas/Sorties/Uscite
(amarillo/jaune/giallo)
activado/allue/acceso
Señal-1 en entrada/salida
Signal 1 sur entrée/sortie
Segnale logico 1 nell’ingresso/uscita
apagado/éteinte/spendo
Señal-0 en entrada/salida
Signal 0 sur entrée/sortie
Segnale logico 0 nell’ingresso/uscita
3
12
5
4
4
5
ASI-4DI3DO-M12X2-5POL-Z
Instrucciones de funcionamiento
Notice d’utilisation
Istruzioni d’uso
Original: de
Festo SE & Co. KG
Postfach
D-73726 Esslingen
Phone:
+49/711/347-0
www.festo.com
0508NH 694 049
IND. CONT. EQ. – 29TS


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: ASI-4DI3DO-M12X2-5POL-Z

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo ASI-4DI3DO-M12X2-5POL-Z stil et spørgsmål nedenfor, og andre brugere vil svare dig