Festo CPX-IOT Manual

Festo Ikke kategoriseret CPX-IOT

Læs gratis den danske manual til Festo CPX-IOT (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Festo CPX-IOT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

CPX-IOT

Gateway

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Deutschland

+49 711 347-0

www.festo.com

Operating instructions

8154928

2021-03b

[8154930]

Translation of the original instructions

EtherNet/IP®, OPC UA®, PI PROFIBUS PROFINET®, SPEEDCON® are registered

trademarks of the respective trademark owners in certain countries.

1 Applicable documents

All available documents for the product

è www.festo.com/sp.

Document Table of contents

CPX system descrip-

tion (CPX-SYS-...)

–Detailed information on the CPX terminal.

–General information on the [PS] and [SF] LEDs.

–General information on the equipotential bonding of the functional

earth.

Application notes è www.festo.com/sp

–Enter ‘CPX-IOT’ keyword.

–Expert knowledge on the product application.

–Commissioning instructions

Tab. 1: Applicable documents

2 Safety

2.1 Safety instructions

–Use the product in its original status without any unauthorised modifications.

–Use the product only within the limits defined by the technical data.

–Before working on the product: switch off the power supply and secure it

against being switched back on.

–Observe the handling specifications for electro-statically sensitive devices.

–Only commission a module that is completely mounted and connected.

2.2 Intended use

The product is intended for use in an industrial environment as a gateway

between Industrial Ethernet networks and an on-premise MQTT broker.

Outside industrial environments, e.g. in commercial and residential/mixed-use

areas, it may be necessary to take measures to suppress radio interference.

2.3 Training of qualified personnel

Work on the product should only be conducted by qualified personnel. The quali-

fied personnel must be familiar with installation of electrical control systems.

3 Additional information

–Contact the regional Festo contact if you have technical problems

è www.festo.com.

–Accessories and spare parts è www.festo.com/catalogue.

4 Product overview

4.1 Licence information

This product uses open-source software.

Licence Version

GNU General Public License Version 2

GNU Lesser General Public License Version 2.1

Tab. 2: Open-source software

The licence conditions of the GPL, LGPL and the other open-source licences can be

viewed via the integrated web server of the product:

1. Connect the gateway to a computer at the ‘Device’ network connection.

2. Call up the web server and log in è 7.2 Parameterisation.

https://<IP_address_of_the_network_connection_‘Device’>/cgi-bin/system-

about

4.2 Structure

4.2.1 Product design

Fig.1

LED displays

"Cloud" network connection

"Device" network connection

Rotary switch for the operating

mode

DIL switches

Interface to the CPX terminal

4.2.2 LED displays

Network-specific LED displays Gateway-specific LED displays

Cloud

(blue)

‘Cloud’ network status PS

(green)

‘operating power supply’ status

(red/green)

‘Device’ network status PL reserved

TP1

(green)

‘Cloud’ connection status

(Link/Traffic)

(red)

System errors

TP2

(green)

‘Device’ connection status

(Link/Traffic)

(yellow)

Module status

Tab. 3: LED displays

Normal operating status

Behaviour of the LED displays in the normal operating status:

–The [PS] and [NS] LEDs are green.

–The [Cloud] LED is blue.

–The [TP1] and/or [TP2] LEDs are steady green or flashing green.

–The [PL], [SF] and [M] LEDs are off.

Module location

The [PS], [PL] and [NS] flash synchronously.

4.2.3 Switching elements

Fig.2

DIL switch 1

DIL switch 2

Rotary switch for the operating

mode

DIL switches

DIL switch 1 Description

1: OFF

2: OFF

(delivery status)

reserved

1: ON

2: ON

reserved

Tab. 4: DIL switch 1

DIL switch 2 Description

1: OFF

2: OFF

(delivery status)

reserved

1: OFF

2: ON

reserved

DIL switch 2 Description

1: ON

2: OFF

è 8.2.2 Resetting web server SSL certificates to fac-

tory setting

1: ON

2: ON

è 8.2.1 Reset gateway to factory setting

Tab. 5: DIL switch 2

Rotary switch for the operating mode

Switching position Operating mode/function

0: Off –‘Cloud’ network connection is deactivated (interface switched

off ).

–No communication with the MQTT broker network and no com-

munication with field devices.

1: Onboarding reserved

2: Read only –Gateway sends process data of the configured field devices to

configured MQTT brokers.

–Manual adding of field devices is enabled.

–Automatic adding of field devices via the Auto-Scan function is

blocked.

–Removal of field devices is blocked.

3: Read/Write –The gateway sends process data from the configured field

devices to the MQTT broker network.

–Manual adding of field devices is enabled.

–Automatic adding of field devices via the Auto-Scan function is

enabled.

–Parameters of connected devices can be changed.

Tab. 6: Rotary switch for the operating mode

4.2.4 Network connections

There are 2 Industrial Ethernet interfaces on the gateway for connection to an

MQTT broker and for the Industrial Ethernet network with connection to field

devices. The ‘Cloud’ and ‘Device’ network connections. Both connections have

auto-negotiation and crossover detection.

The following table shows the pin allocation with deactivated Crossover detection:

Connection Pin Cloud Device

Signal Explanation Signal Explanation

1 TD+ Transmitted data + RD+ Received data +

2 RD+ Received data + TD+ Transmitted data +

3 TD– Transmitted data – RD– Received data –

4 RD– Received data – TD– Transmitted data –

Shielding1) FE,

Shield

Functional earth FE,

Shield

Functional earth

1) connected to functional earth via RC link

Tab. 7: Network connections

4.2.4.1 MQTT broker

The connection to an MQTT broker is established via the ‘Cloud’ network connec-

tion.

4.2.4.2 Fieldbus protocol and field devices

The ‘Device’ network connection can be used to connect field devices with an

Industrial Ethernet connection directly to the Gateway, e.g. bus nodes or control-

lers (controller, PLC) with protocols such as PROFINET, EtherNet/IP or OPC UA.

4.2.5 Connection technology

The M12 socket [6] (

Fig. 1) can be used to connect a CPX terminal without

network connection, i.e. without Industrial Ethernet connection, directly to the

gateway.

Connection Connecting hardware Cover cap

‘Cloud’ network connection NECU-M-S-D12G4-C2-ET plug ISK-M12

‘Device’ network connection

Interface to the CPX terminal

without network connection

NEBC-M12G5-S-1.5-N-M12G5 con-

necting cable

Tab. 8: Connection technology

5 Assembly

WARNING

Risk of injury due to electric shock.

• For the electric power supply, use PELV circuits that guarantee a reliable electric

disconnection from the mains network.

• Observe IEC 60204-1/EN 60204-1.

• Connect all circuits for the operating and load voltage supply.

NOTICE

Material damage due to incorrect mounting.

Select screws that are suitable for the material of the interlinking block:

• Polymer: thread-grooving screws

• Metal: screws with metric thread

When ordering a single gateway, all the required screws are included.

The gateway is mounted in an interlinking block of the CPX terminal.

–Version 1:

Gateway in an interlinking block with system supply, e.g. CPX-GE-EV-S-...

–Version 2:

Gateway in an interlinking block without system supply between two end

plates with system supply, e.g. CPX-EPL-EV-S-...

Fig. 3: Mounting (version 1)

1 Gateway CPX-IOT

2 Screw

3 Interlinking block

(with system supply)

1. Check the seal and the seal surfaces.

2. Replace damaged seal.

3. Push the gateway carefully and without tilting into the interlinking block up to

the stop.

4. Screw the screws into the existing thread.

Tighten the screws in crosswise.

–Tightening torque: 1 Nm ± 10%

6 Installation

6.1 General information about installation

WARNING

Risk of injury due to electric shock.

• For the electric power supply, use PELV circuits that guarantee a reliable electric

disconnection from the mains network.

• Observe IEC 60204-1/EN 60204-1.

• Connect all circuits for the operating and load voltage supply.

NOTICE

Short circuit as a result of ingress of liquids or foreign matter.

Damage to the electronics or malfunction.

• Use connection hardware with the required degree of protection.

• Use cover caps to seal unused connections.

• Only operate the product with cover for DIL and rotary switches mounted.

The operating and load voltage supply is via an interlinking block with system

supply or via an end plate with system supply.

Information on power supply:

è System description of the CPX terminal (CPX-SYS)

è Pin allocation power supply connection (CPX-PIN-BEL)

Comply with the handling specifications for electro-statically sensitive devices.

NOTICE

Unauthorised Access to the Device Can Cause Damage or Malfunction.

• When connecting the device to a network, protect the network from unauthor-

ised access.

Standards for security in information technology can be used for network

protection measures, e.g. IEC 62443, ISO/IEC 27001.

7 Commissioning

7.1 Selecting operating mode of the gateway

A gateway operating mode must be selected to establish a connection to an MQTT

broker

è Rotary switch for the operating mode.

The rotary switch must be set to [Read only] or [Read/Write] to establish a connec-

tion to the MQTT broker and to the field devices.

7.2 Parameterisation

The gateway is parameterised via the integrated web server of the gateway.

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	CPX-IOT

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo CPX-IOT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025

Festo VABD-S2-1-S-C Manual

20 August 2025

Festo SIED-M18B-ZO-S-L Manual

19 August 2025

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025

Festo P.BE-CP-CO-DE Manual

19 August 2025

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kimo LR 110 Manual

2 September 2025

HMS Premium LPD02 Manual

2 September 2025

AVer E1008 Manual

2 September 2025

Biltema 17-547 Manual

2 September 2025

Groen AH/1E Manual

2 September 2025

ACOPower HY-P30 Manual

2 September 2025

Yamaha True X Speaker 3A WS-X3A Manual

2 September 2025

Globe RG30 Manual

2 September 2025

Deye SUN-6K-SG05LP1-EU-AM2-P Manual

2 September 2025

Neutrik NLT4FXX Manual

2 September 2025