Festo CTEU-AS Manual

Festo Ikke kategoriseret CTEU-AS

Læs gratis den danske manual til Festo CTEU-AS (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Festo CTEU-AS, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
Bus node
CTEU-AS
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
Description
Installation and interfaces
Translation of the original instructions
8101686
2018-11a
[8101688]
Bus node CTEU-AS English. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For all available product documentation è www.festo.com/pk
1 Instructions on this description
This description includes information for mounting the bus node on an I-port-com
patible device from Festo (e.g. valve terminal with I-port interface) and for installa
tion of this combination in a higher-level control system.
AS-Interface® and TORX® are registered trademarks of the respective
trademark owners in certain countries.
2 Intended use
The bus node type CTEU-AS has been designed exclusively for use as a slave on
the AS-interface fieldbus. It may only be used in its original status without unau
thorised modifications and only in perfect technical condition.
The bus node is intended for use in an industrial environment. Outside of industrial
environments, e.g. in commercial and mixed-residential areas, actions to suppress
interference may have to be taken.
3 Target group
The target group for this description consists of trained specialists in control and
automation technology who have experience with installation of stations on the
AS-interface fieldbus.
4 Mounting
Warning
Danger of injury to people, damage to the machine and system resulting from
uncontrolled movements of the actuators and undefined switching states
Switch off the operating and load voltage supplies.
Switch off compressed air supply.
Exhaust the pneumatics valve terminal.
Note
Damage to the electronics
The bus node includes electrostatically sensitive devices.
Do not touch any electrical/electronic components.
Observe the handling specifications for electrostatically sensitive devices.
Note
Use cover caps to seal unused connections. You will then achieve degree of pro
tection IP65/IP67.
Information on mounting the bus node on the decentralised electrical
connecting plate CAPC-... can be found in the mounting instructions that
accompany the connecting plate.
The bus node CTEU-AS supports only the X1 connection of the electrical
connecting plate CAPC-.... The X2 connection on the electrical connecting
plate CAPC-... is without a function for the CTEU-AS bus node.
For mounting the bus node on a valve terminal with I-Port interface, proceed as
follows:
1. Inspect the seals and sealing surfaces on bus node and valve terminal.
2. Plug the bus node onto the valve terminal in the right position and without tilt
ing.
3. Screw the three self-tapping screws in by hand. You can use the threads already
present when you screw it in again.
4. Tighten the screws by hand in diagonally opposite sequence, with a tightening
torque of 0.7 ± 0.1 Nm.
5 Connection and display components
The following electrical connection and display components can be found on the
bus node:
1
3
4
2
1DIL switch group (è chap. 7.2)
2Status LEDs (status display/
diagnostics è chap. 8)
3M12 plug for AS-interface bus and
additional power supply (AS-i In)
(è chap. 6)
4M12 socket, AS-interface bus and
additional power supply (AS-i Out)
(è chap. 6 )
Fig. 1
6 Connect AS-interface bus and auxiliary power supply
The bus node also supplies voltage to equipment connected via the I-port inter
face.
Warning
Danger of electric shock
Only use PELV circuits in accordance with IEC/EN 60204-1 (protective extra-
low voltage, PELV) for the electrical power supply.
Observe also the general requirements for PELV power circuits in accordance
with IEC/EN 60204-1.
Only use voltage sources which guarantee reliable electrical isolation of the
operating voltage in accordance with IEC/EN 60204-1.
Through the use of PELV circuits, protection against electric shock (protection
against direct and indirect contact) is ensured in accordance with IEC/EN 60204-1.
Observe with branch lines:
– the maximum overall length of the AS-interface bus (100 m without repeater/
extender)
– the line length of the load voltage connection cable (depends on the current
consumption of the valve terminal and fluctuations in load voltage).
M12 plug, AS-interface In Pin Allocation
1
3
2
41 AS-interface +
2 0 V (auxiliary power supply)
3 AS-interface –
4 24 V (auxiliary power supply)
Fig. 2

Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: CTEU-AS

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo CTEU-AS stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Festo Manualer

Festo

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025
Festo

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025
Festo

Festo VABD-S2-1-S-C Manual

20 August 2025
Festo

Festo SIED-M18B-ZO-S-L Manual

19 August 2025
Festo

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025
Festo

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025
Festo

Festo P.BE-CP-CO-DE Manual

19 August 2025
Festo

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025
Festo

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025
Festo

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hendi

Hendi 551813 Manual

2 November 2025
BougeRV

BougeRV E50 Manual

2 November 2025
Beverage-Air

Beverage-Air VueMax VMHC-7-1-G Manual

2 November 2025
OneConcept

OneConcept Magic-Carpet DX Manual

2 November 2025
Tonor

Tonor T20 Manual

2 November 2025
Beverage-Air

Beverage-Air Horizon HRP3HC-1HS Manual

2 November 2025
Workzone

Workzone AB1600 Manual

2 November 2025
Homedics

Homedics BH-100-AU Manual

2 November 2025
Beverage-Air

Beverage-Air Horizon HFP1HC-1S Manual

2 November 2025
Beverage-Air

Beverage-Air VueMax VMHCSL-18-1-B Manual

2 November 2025