Festo DHPC-10-A-NO-S Manual

Festo Ikke kategoriseret DHPC-10-A-NO-S

Læs gratis den danske manual til Festo DHPC-10-A-NO-S (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Festo DHPC-10-A-NO-S, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
DHPC
Parallel gripper
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Operating instructions
8150807
2021-05a
[8150809]
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable Documents
All available documents for the product
è www.festo.com/sp.
2 Safety
2.1 Safety Instructions
–Take into consideration the ambient conditions at the location of use.
–Only use the product in original status without unauthorised modifications.
–Observe labelling on the product.
–Store the product in a cool, dry, UV-protected and corrosion-protected environ-
ment. Ensure that storage times are kept to a minimum.
–Prior to mounting, installation and maintenance work: Switch off compressed
air supply and secure it from being switched back on.
–Observe tightening torques. Unless otherwise specified, the tolerance is
± 20 %.
2.2 Intended use
The intended use of the product is to grip and hold payloads (workpieces) using
custom-designed gripper fingers attached by the customer.
2.3 Training of qualified personnel
Installation, commissioning, maintenance and disassembly should only be con-
ducted by qualified personnel.
The specialized personnel must be familiar with the installation and operation of
electrical and pneumatic control systems.
3 Additional information
–Contact the regional Festo contact if you have technical problems
è www.festo.com.
–Accessories and spare parts è www.festo.com/catalogue.
4 Product overview
4.1 Function
–Alternating pressurisation of the supply ports causes a piston in the gripper to
move (double-acting).
–A gripper with integrated spring return is used to exert the gripper force. When
exhausting the single-acting gripper: the spring return moves the gripper jaws
to the initial position.
–N/O contact: NO (normally open)
–N/C contact: NC (normally closed)
–The piston movement is transmitted mechanically to the gripper jaws. Gripper
fingers are fastened to the gripper jaws. Closing or opening the gripper fingers
clamps the payload to the outer contour (external gripping) or the inner contour
(internal gripping).
–The gripping force is adjusted by external regulation of the operating pressure.
–The gripper has integrated fixed flow restrictors. If the max. gripper finger
weights and the max. gripper finger lengths are in compliance, an external flow
control is not required.
4.2 Structure
1
2
3
4
5
Fig. 1: Structure
1
Gripper jaw
2
Threaded hole for mounting
3
Locating hole
4
Supply port
5
Slot for proximity switch
5 Assembly
5.1 Preparing the gripper fingers
The gripper fingers are not included in the delivery.
Requirements for the gripper fingers è 11 Technical data:
–Observe the max. permissible forces and max. permissible torques at the
gripper jaw.
–Observe the max. length and max. weight.
–Use gripper fingers that are as short and light as possible.
–Manufacture gripper fingers that are suitable for the payload and type of grip-
ping action.
Size 6 10 16
Width at gripper jaws [mm] 4.3–0.05 5.4–0.05 7–0.05
Tab. 1: Width of gripper jaws
Size 20 25 32 40
Width at gripper jaws [mm] 8.3–0.05 12–0.05 15.2–0.05 18–0.05
Tab. 2: Width of gripper jaws
5.2 Mounting the gripper fingers
1 2 3 4
5
Fig. 2: Mounting the gripper fingers
1
Screw
2
Gripper finger
3
Gripper jaw A
4
Gripper jaw A-...-1
5
Gripper jaw A-...-2
• Position the prepared gripper fingers [2] on the gripper jaws [3], [4], [5] and
fasten each one with two screws [1]. Fix the gripper jaws in place during
mounting and use the specified tightening torque.
DHPC -6-... -10-...
A A-...-1 A-...-2 A A-...-1 A-...-2
Screw M3 M2 M3 M2.5
Tightening torque [Nm] 0.59 0.15 0.59 0.31
Tab. 3: Dimensions and tightening torque
DHPC -16-... -20-...
A A-...-1 A-...-2 A A-...-1 A-...-2
Screw M3 M4
Tightening torque [Nm] 0.59 1.4
Tab. 4: Dimensions and tightening torque
DHPC -25-... -32-...
A A-...-1 A-...-2 A A-...-1 A-...2
Screw M5 M6
Tightening torque [Nm] 2.8 4.9
Tab. 5: Dimensions and tightening torque
DHPC -40-...
A A-...-1 A-...-2
Screw M8
Tightening torque [Nm] 11.8
Tab. 6: Dimensions and tightening torque
5.3 Mounting gripper
If necessary, mount the proximity switches before mounting the gripper.
When using proximity switches for sensing the end position, take the following
into account:
• Interference from ferritic attachments, e.g. retaining screws made of ferritic
steel.
• Projecting proximity switches, if applicable.
• Cable outlet direction of the proximity switches.
• Sufficient space for the connection components.
• When sensing from both end positions: use separate slots for the proximity
switches.
Vertical mounting
1 2
Fig. 3: Direct mounting via thread in
the housing
1
Thread
2
Locating hole
Size 6 10 16 20 25 32 40
Thread [1] M3 M4 M5 M6 M8
Depth of thread 10 4.75 6.75 9.6 13 15 18
Tightening torque [Nm] 0.88 0.69 2.1 4.3 7.9 10 18
Locating hole for centring@
pin [2]
[mm] – 2H9 3H9 4H9 5H9
Depth of locating hole [mm] – 3 4 5
Tab. 7: Direct mounting via thread in the housing
1 2 3
Fig. 4: Direct mounting via through-
hole
1
Thread
2
Locating hole (not for size 6)
3
Depth of locating hole (not for
size 6)
Size 6 10 16 20 25 32 40
Thread [1] M2.5 M2.5 M3 M4 M5 M6
Tightening torque [Nm] 0.49 0.49 0.88 2.1 4.3 7.3
Locating hole for centring@
pin [2]
[mm] – 2H9 3H9 4H9 5H9
Depth of locating hole [3] [mm] – 3 4 5
Tab. 8: Direct mounting via through-hole
Horizontal mounting
1
2
Fig. 5: Horizontal mounting
1
Locating hole (not for size 6)
2
Thread
Size 6 10 16 20 25 32 40
Thread [2] M2 M3 M4 M5 M6 M8
Thread depth [mm] 4.5 4 4.5 7.5 10 13
Tightening torque [Nm] 0.15 0.9 1.6 3.3 5.9 13.7
Locating hole for centring@
pin [1]
[mm] – 2H9 3H9 4H9 5H9
Depth of locating hole [mm] – 3 3 4 5
Tab. 9: Horizontal mounting
Mounting on the bottom
1
2 3 4
Fig. 6: Mounting on the bottom
1
Thread
2
Locating hole (not for size 6)
3
Positioning via base provided by
customer
4
Axial mounting by customer
Size 6 10 16 20 25 32 40
Thread [1] – M3 M4 M5 M6 M8
Thread depth [mm] – 4 6 10 12 13 17
Tightening torque [Nm] – 0.88 2.1 4.3 7.3 7.9 17.7
Locating hole for centring@
pin [2]
[mm] – 2H9 3H9 4H9 5H9
Depth of locating hole [mm] – 3 4 5
Positioning via base provided by customer [3]
Locating hole [mm] – 12@H9 17H8 21H8 26H8 33H9 41H9
Depth of locating hole [mm] – 1.5 2 3 3.5 4
Axial mounting by customer [4]
Clamping surface [mm] 8@f8 12f8 16f8 20f8 25f8 32f8
Clamping surface height [mm] 10 15 18 20 23
Tab. 10: Mounting on the bottom
6 Installation
6.1 Pneumatic installation
NOTICE
Loss of function due to contamination in the connections.
• Keep ports and tubing lines free from dirt particles and foreign matter.
The use of a check valve prevents the payload from dropping in the event of
a sudden pressure drop. The use of a one-way flow control valve also permits
adjustment of the opening and closing time.

Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: DHPC-10-A-NO-S

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo DHPC-10-A-NO-S stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Festo Manualer

Festo

Festo KYC-63 Manual

9 Juli 2025
Festo

Festo NEBM-L10G14-EH-5-Q7N-LE12 Manual

8 Juli 2025
Festo

Festo CPX-E-8DO Manual

8 Juli 2025
Festo

Festo CRDSNU-20-80-P-A Manual

8 Juli 2025
Festo

Festo CRDSNU-16-10-P-A Manual

8 Juli 2025
Festo

Festo CPV-SC-FB-VI Manual

7 Juli 2025
Festo

Festo CRDSNU-B-16-50-P-A-MG-A1 Manual

7 Juli 2025
Festo

Festo NEBM-L10G14-EH-10-Q7N-LE12 Manual

7 Juli 2025
Festo

Festo CPX-CTEL-4-M12-5POL Manual

7 Juli 2025
Festo

Festo CRDSNU-B-25-25-PPS-A-MG-A1 Manual

7 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Microchip

Microchip ATTINY861 Manual

19 Juli 2025
Husqvarna

Husqvarna Aspire P4A 18-C100 Manual

19 Juli 2025
Ikea

Ikea TJUSIG 201.526.34 Manual

19 Juli 2025
Atlona

Atlona AT-VGW-250 Manual

19 Juli 2025
Sharkoon

Sharkoon MK3 Manual

19 Juli 2025
Yamaha

Yamaha WaveRunner FX SVHO (2025) Manual

19 Juli 2025
Fuxtec

Fuxtec FX-GS36S Manual

19 Juli 2025
Bartscher

Bartscher 3L-1 Manual

19 Juli 2025
Guede

Guede GF 3060.1 Manual

19 Juli 2025
ChamSys

ChamSys GeNetix GD10 Manual

19 Juli 2025