Festo HMIXB-RP/FP Manual


Læs gratis den danske manual til Festo HMIXB-RP/FP (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Festo HMIXB-RP/FP, eller vil du spørge andre brugere om produktet?

Side 1/2
1. Installationsbausatz mit Montagebeispiel
1.a. HMIXB-RP/FP
1 Installationsbausatz
HMIXB-RP/FP
inklusive Befestigungs-
elemente A-C (siehe
Tabelle).
1.b. Montagebeispiel
2 Auflageprofil
HMIA-E07-X
Bestimmungsgemäß dient
der Installationsbausatz 1
als Befestigungsplatte für
das Auflageprofil 2 beim
Aufbau von Raum- und Flä-
chenportalsystemen zur
Verlegung von Energiefüh-
rungsketten der X-Achsen.
Hinweis
• Befestigen Sie einen Installationsbausatz mindestens alle 500 mm.
• Berechnen Sie die dazu benötigte Anzahl y nach folgenden Formeln:
- bei Hub 500 mm: y = 2
- bei Hub > 500 mm : y = Ganzzahl (Hub/500) + 2
• Montieren Sie den Installationsbausatz zuerst an die X-Achsen 3.
2. Befestigungsschnittstellen für X-Achsen am HMIXB-RP/FP
2.a. Schnittstelle für X-Achse DGE-25-...
1 Installationsbausatz
HMIXB-RP/FP
3 Linearantrieb
DGE-25-...
2.b. Schnittstelle für X-Achse DGE-40-...
1 Installationsbausatz
HMIXB-RP/FP
3 Linearantrieb
DGE-40-...
3. Befestigungsschnittstellen für Anbaukomponenten
3.a. Schnittstelle für HMIA-E07
1 Installationsbausatz
HMIXB-RP/FP
2 Auflageprofil
HMIA-E07-X
3 Linearantrieb
DGE-...
4 Energieführungskette
Justieren Sie die E-Kette 4
bzw. das Auflageprofil 2
entsprechend der Befesti-
gung am HMIXF-RP/FP.
Lesen Sie dazu die Monta-
geanleitung des Installati-
onsbausatzes
HMIXF-RP/FP.
4. Basisbefestigungsschnittstellen für X-Achsen
4.a. Schnittstelle für Basisbefestigung der X-Achse DGE-25-...
1 Installationsbausatz
HMIXB-RP/FP
2 Auflageprofil
HMIA-E07-X
3 Linearantrieb
DGE-25-...
4 Energieführungskette
4.b. Schnittstelle für Basisbefestigung der X-Achse DGE-40-...
1 Installationsbausatz
HMIXB-RP/FP
2 Auflageprofil
HMIA-E07
3 Linearantrieb
DGE-40-...
4 Energieführungskette
Hinweis
Nach der Montage:
• Verfahren Sie die Achsen von Hand (Y-Modul mit vollem Hub in
X-Richtung) und überprüfen Sie dabei die Installation bzw. das leichte
Abrollen der Energieführungsketten. Justieren Sie gegebenenfalls nach.
Hinweis
• Verwenden Sie nur zulässige Energieführungsketten laut Katalog.
• Beachten Sie:
- dass nur Befestigungskombinationen aus der Tabelle zulässig sind.
- dass Befestigungselemente bei manchen Kombinationen übrig bleiben.
- zur Erdung, die Montageanleitung des Erdungsbausatzes.
Montageanleitung (de)
688613 / 2005-03NH
†‡
Installationsbausatz
HMIXB-RP/FP
Festo SE & G Co. K
Postfach
73726 Esslingen
++49/(0)711/347-0
www.festo.com
1
Installationsbausatz
Typ
Teile-Nr.
Antriebseinheiten 33233
3 3 2 3 3
33233
3 3 2 3 33 3 2 3 3
Typ DGE-25-... DGE-40-... HMIA-E07-X DGE-25-... DGE-40-...
Schnittstelle 2.a. 2.b. 3.a. 4.a. 4.b.
Zylinderschrauben
M5x8 DIN 6912 4x 2x
Senkschrauben
M4x10 DIN 7991 2x
Nutensteine
HMV-M4 2x
NST-5-M5 4x 2x
Mittenstützen
MUP-18/25 8x
MUP-40 8x
M4 M5
2,9 5,8
C
D
Anzugsdrehmomente in Nm
Befestigungselemente nicht im Lieferumfang
Gewinde
1
1
1
11
HMIXB-RP/FP
B
Befestigungselemente im Lieferumfang der Bausätze
539 654
A
3
1
C
1
2
B
3
1
C
A
3
C
A
1
3
D
1
D
2
1
4
4
2
3
4
2
1. Installation kit with assembly example
1.a. HMIXB-RP/FP
1 Installation kit
HMIXB-RP/FP
Including mounting at-
tachments A-C (see ta-
ble).
1.b. Assembly example
2 Support profile
HMIA-E07-X
The installation kit 1 has
been designed as a fastening
plate for the support profile
2 when 3D and planar
surface gantry systems are
set up, in order that chain
link trunkings for the X-axes
can be laid.
Note
• Attach a basic kit at least every 500 mm.
• Calculate the required quantity y using the following formulas:
- Where stroke length 500 mm: y = 2
- Where stroke length > 500 mm: y = whole-number (stroke/500) +2
• Fit the installation kit first onto the X-axes 3.
2. Fastening interfaces for the X-axes on the HMIXB-RP/FP
2.a. Interface for X-axis DGE-25-...
1 Installation kit
HMIXB-RP/FP
3 Linear drive
DGE-25-...
2.b. Interface for X-axis DGE-40-...
1 Installation kit
HMIXB-RP/FP
3 Linear drive
DGE-40-...
3. Mounting interfaces for attachment components
3.a. Interface for HMIA-E07
1 Installation kit
HMIXB-RP/FP
2 Support profile
HMIA-E07-X
3 Linear drive
DGE-...
4 Chain link trunking
Adjust the Cl-trunking 4 or
the support profile 2 cor-
responding to the fasten-
ing on the HMIXF-RP/FP.
Refer to the assembly
instructions for installation
kit HMIXF-RP/FP to this
end.
4. Basic fastening interfaces for X-axes
4.a. Interface for basic fastening of X-axis DGE-25-...
1 Installation kit
HMIXB-RP/FP
2 Support profile
HMIA-E07-X
3 Linear drive
DGE-25-...
4 Chain link trunking
4.b. Interface for basic fastening of X-axis DGE-40-...
1 Installation kit
HMIXB-RP/FP
2 Support profile
HMIA-E07
3 Linear drive
DGE-40-...
4 Chain link trunking
Note
After assembly:
• Advance the axes manually (Y-module with full stroke in X-direction),
and check for correct installation of the chain link trunking, i.e. smooth
rolling. Make further adjustments if necessary.
Note
• Use permissible chain link trunking only, as specified in the catalogue.
• Please note:
- that only attachment combinations shown in the table are permissible.
- that mounting attachments are left over with some combinations.
- for earthing, the assembly instructions for the earthing kit.
Assembly instructions (en)
688613 / 2005-03NH
†‡
Installation kit
HMIXB-RP/FP
Festo SE & G Co. K
Postfach
73726 Esslingen
++49/(0)711/347-0
www.festo.com
1
Installation kit
Type
Part No.
Drive units 33233
3 3 2 3 3
33233
3 3 2 3 33 3 2 3 3
Type DGE-25-... DGE-40-... HMIA-E07-X DGE-25-... DGE-40-...
Interface 2.a. 2.b. 3.a. 4.a. 4.b.
Socket head screws
M5x8 DIN 6912 4x 2x
Countersunk screws
M4x10 DIN 7991 2x
Slot nuts
HMV-M4 2x
NST-5-M5 4x 2x
Central supports
MUP-18/25 8x
MUP-40 8x
M4 M5
2.9 5.8
1
1
1
11
HMIXB-RP/FP
B
Mounting attachments included with kits
539 654
A
C
D
Tightening torques in Nm
Mounting attachments not included in scope of delivery
Threads
3
1
C
1
2
B
3
1
C
A
3
C
A
1
3
D
1
D
2
1
4
4
2
3
4
2


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: HMIXB-RP/FP

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo HMIXB-RP/FP stil et spørgsmål nedenfor, og andre brugere vil svare dig