Festo HMVD-LP-DL63 Manual

Festo Ikke kategoriseret HMVD-LP-DL63

Læs gratis den danske manual til Festo HMVD-LP-DL63 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Festo HMVD-LP-DL63, eller vil du spørge andre brugere om produktet?

Side 1/2
Montageanleitung (de)
744 374 / 2009-09NH
†‡
Grundbausatz
HMVD-LP-DL63
Festo SE & G Co. K
Postfach
D-73726 Esslingen
++49/(0)711/347-0
www.festo.com
1. Grundbausatz
1a. HMVD-LP-DL63
13914d_2
1 Grundbausatz
HMVD-LP-DL63
1b. Montagebeispiel
13914d_1..Linienportal
2 Antriebseinheit
(! Tabelle)
3 Führungseinheit
(! Tabelle)
Bestimmungsgemäß dient der Grundbausatz HMVD-LP-DL63 1 als Basis
zum Aufbau von Linienportalsystemen in Duo-Bauweise (Y-Achse).
Warnung
Verletzungsgefahr durch elektrische Spannung.
Verbinden Sie den Bausatz 1 mit dem Schutzleitersystem
! Montageanleitung Erdungsbausatz für HM…63… (HMVS-DL63).
Hinweis
Befestigen Sie einen Bausatz 1 mindestens alle 500 mm.
Berechnen Sie die dazu benötigte Anzahl y nach folgenden Formeln:
bei Hub 500 mm: y = 2
bei Hub > 500 mm: y = Ganzzahl (Hub/500) +2
Montieren Sie die Antriebe, Führungen immer zuerst an den Bausatz 1.
Beachten Sie, dass nur Befestigungskombinationen aus der Tabelle zu-
lässig sind.
Halten Sie die zulässigen Anziehdrehmomente ein (! Tabelle).
Info
Beachten Sie die Montagereihenfolge
! Montageübersicht für HM…63… (HMVS-DL63).
Der Bausatz 1 enthält alle maximal erforderlichen Befestigungselemente.
Beachten Sie, dass bei einigen Kombinationen Befestigungselemente üb-
rig bleiben.
2. Montage Antriebs-/ Führungseinheiten 2
2
2
223
3
3
3 3 (Duo-Bauweise)
Wählen Sie die Befestigungselemente (Schrauben, usw.) für Ihre Kombina-
tion (! Tabelle).
Beachten Sie die Bildzuordnung für Ihre Kombination (! Tabelle).
Bild 1
13914d_3
1 Grundbausatz
HMVD-LP-DL63
2 Antriebseinheit
DGC-50-…-KF
3 Führungseinheit
DGC-50-…-FA
Bild 2
13914d_4
1 Grundbausatz
HMVD-LP-DL63
2 Antriebseinheit
DGC-63-…-KF
3 Führungseinheit
DGC-63-…-FA
1)2)
1) Toleranzen für nicht tolerierte Anziehdrehmomente MA
MA
> 1 Nm: ± 20%
2) Weitere Kombinationen mit Antriebseinheit 2 z. B. DGPL / DGE sind nur in Kombination mit
Adapterbausatz HMVA-63 erreichbar.
3. Montage Anbaukomponenten 4
4
4
44
Wählen Sie die Befestigungselemente (Schrauben, usw.) für Ihre Kombina-
tion (! Tabelle).
Beachten Sie die Bildzuordnung für Ihre Kombination (! Tabelle).
Bild 3
Bild 3a
13914d_5
1 Grundbausatz
HMVD-LP-DL63
4 Profil
HMBS-80/80
Bild 3b
13914d_6
1 Grundbausatz
HMVD-LP-DL63
4 Profil
HMBS-80/80
Bild 3c
13914d_7
1 Grundbausatz
HMVD-LP-DL63
4 Profil
HMBS-80/80
Bild 3d
13914d_8
1 Grundbausatz
HMVD-LP-DL63
4 Profil
HMBS-80/80
Linienportal
3289d_4
1
1
2
1
3
1
1
1
4
4
2
1
C
D
B
A
E
3
2
B
E
A
D
C
4
D
C
4
D
50 63
50 63
1 2 3a 3b 3c 3d
M
A
1)
[Nm]
M5x16 6
M8x16 24 6x 6x
Ø6m6x24 4x 4x
M8x30 24 16x
NST-HMV-8-2-M8 16x
MUC-50 2x
MUC-63 2x
D Nutenstein
E Profilbefestigung
C Zylinderschraube nach DIN 912
4 Anbaukomponente
8x
8x
Befestigungselemente nicht im Lieferumfang
HMBS-80/80
3 Führungseinheit
Bild
A Zylinderschraube nach DIN 912
B Zylinderstift nach DIN 7
HMVD-LP-DL63
2)
1 Bausatz HMVD-LP-DL63
2 Antriebseinheit DGC-...-KF
DGC-...-FA
3
4
4
C
1
Assembly instructions (en)
744 374 / 2009-09NH
†‡
Basic kit
HMVD-LP-DL63
Festo SE & G Co. K
Postfach
D-73726 Esslingen
++49/(0)711/347-0
www.festo.com
1. Basic kit
1a. HMVD-LP-DL63
13914d_2
1 Basic kit
HMVD-LP-DL63
1b. Assembly example
13914d_1..Linienportal
2 Drive unit
(!Table)
3 Guide unit
(!Table)
The basic kit HMVD-LP-DL63 1 is intended for use as a basis for the setup of
linear gantry systems in duo design (Y axis).
Warning
Danger of injury due to electric voltage.
Connect the kit 1 with the protective conductor system
! Assembly instructions for earthing kit for HM…63… (HMVS-DL63).
Note
Attach a basic kit 1 at least every 500 mm.
Calculate the required quantity y using the following formulas:
Where stroke length 500 mm: y = 2
Where stroke length > 500 mm: y = whole-number (stroke/500) +2
Always mount the drives, the guides or the displacement system on the
basic kit first 1.
Note, that only the fastening combinations shown in the table are per-
missible.
Maintain the permitted tightening torques (!Table).
Information
Follow the mounting sequence
! Mounting overview for HM…63… (HMVS-DL63).
The kit 1 contains all maximum necessary mounting components.
Note that mounting components may be left over with some combina-
tions.
2. Mounting of the drive / guide units 2
2
2
223
3
3
3 3 (duo design)
Select the mounting components (screws etc.) for your combination
(!Table).
Observe the reference to the figures for your combination (!Table).
Fig. 1
13914d_3
1 Basic kit
HMVD-LP-DL63
2 Drive unit
DGC-50-…-KF
3 Guide unit
DGC-50-…-FA
Fig. 2
13914d_4
1 Basic kit
HMVD-LP-DL63
2 Drive unit
DGC-63-…-KF
3 Guide unit
DGC-63-…-FA
1)2)
1) Tolerance for non-toleranced tightening torques M A
MA
> 1 Nm: ± 20%
2) Additional combinations with drive unit e.g. DGPL / DGE are achievable only in 2
combination with adapter kit HMVA-63.
3. Mounting of the attachment components 4
4
4
44
Select the mounting components (screws etc.) for your combination
(!Table).
Observe the reference to the figures for your combination (!Table).
Fig. 3
Fig. 3a
13914d_5
1 Basic kit
HMVD-LP-DL63
4 Profile
HMBS-80/80
Fig. 3b
13914d_6
1 Basic kit
HMVD-LP-DL63
4 Profile
HMBS-80/80
Fig. 3c
13914d_7
1 Basic kit
HMVD-LP-DL63
4 Profile
HMBS-80/80
Fig. 3d
13914d_8
1 Basic kit
HMVD-LP-DL63
4 Profile
HMBS-80/80
Linear gantry
3289d_4
1
1
2
1
3
1
1
1
4
4
2
1
C
D
B
A
E
3
2
B
E
A
D
C
4
D
C
4
D
50 63
50 63
1 2 3a 3b 3c 3d
M
A
1)
[Nm]
M5x16 6
M8x16 24 6x 6x
Ø6m6x24 4x 4x
M8x30 24 16x
NST-HMV-8-2-M8 16x
MUC-50 2x
MUC-63 2x
3 Guide unit
Fig.
A Socket head screw as per DIN 912
B Cylindrical pin as per DIN 7
HMVD-LP-DL63
2)
1 Kit HMVD-LP-DL63
2 Drive unit DGC-...-KF
DGC-...-FA
D Slot nut
E Profile fastening
C Socket head screw as per DIN 912
4 Attachment component
8x
8x
Mounting components not included in scope of delivery
HMBS-80/80
3
4
4
C
1


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: HMVD-LP-DL63

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo HMVD-LP-DL63 stil et spørgsmål nedenfor, og andre brugere vil svare dig