Festo KVZB Manual

Festo Ikke kategoriseret KVZB

Læs gratis den danske manual til Festo KVZB (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Festo KVZB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

KVZA/KVZB/KDFP

Butterfly valve unit/Ball valve unit/Quarter turn actuator unit

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Deutschland

+49 711 347-0

www.festo.com

Operating instructions

8169367

2021-12b

[8169369]

Translation of the original instructions

1 About this document

This document contains important information on the handling of pre-installed

units consisting of various combinations of process valve, semi-rotary drive, hand

lever, sensorbox, positioner, position indicator or pilot valve. Certain aspects of

use are described in other documents and must be observed

è 1.1 Applicable

Documents

1.1 Applicable Documents

All available documents for the product

è www.festo.com/sp.

2 Safety

2.1 General safety instructions

–Only use the product in its original condition without unauthorised modifica-

tions.

–Only use the product if it is in perfect technical condition.

–Operate product only in completely mounted status.

Return to Festo

Hazardous substances can endanger the health and safety of personnel and

cause damage to the environment. To prevent hazards, the product should only be

returned upon explicit request by Festo.

–Consult your regional Festo contact.

–Complete the declaration of contamination and attach it to the outside of the

packaging.

–Comply with all legal requirements for the handling of hazardous substances

and the transport of dangerous goods.

Operation in potentially explosive areas

The pre-assembled unit KVZB/KDFP is an assembly of devices that have been

individually assessed for possible ignition hazards. An assessment of possible

ignition sources has demonstrated that the assembly has not resulted in the

formation of new ignition hazards.

When operating the unit in a potentially explosive area:

–Consider the assessment of very separate device. To do this, observe the

information on explosion prevention and protection in the user documentation

for the individual devices.

–Include the device in the system equipotential bonding.

2.2 Training of qualified personnel

Work on the product should only be conducted by qualified personnel.

3 Additional information

–Contact the regional Festo contact if you have technical problems

è www.festo.com.

–Accessories and spare parts è www.festo.com/catalogue.

4 Product overview

4.1 Structure

4.1.1 Product design

Fig. 1: Design

1 Carrying strap

2 Semi-rotary drive

3 Process valve with KVZA/KVZB

4 Sensor box

5 NAMUR valve

6 Process valve with KVZA/KVZB

5 Transport

–Protect product from mechanical stresses during transport.

–Do not remove packaging until it is at the installation location.

–Configure load handling equipment to lift the load properly.

6 Assembly

WARNING

Risk of injury if the product overturns or falls.

The product may weigh over 25 kg depending on the product version. Body parts

can be crushed or severed. In overhead installations, the result can be serious

head injuries.

• Secure the product from overturning or falling with appropriate equipment.

1. Thread carrying straps under both sides of the flange mounting of the process

valve or semi-rotary drive to form a sling

è Fig. 1.

2. Lift unit with suitable lifting equipment.

3. Move unit to mounting position.

4. Follow the sequence for mounting the unit:

–Mechanical Installation (mount the unit completely.)

–Pneumatic installation

–Electrical installation (note earthing.)

5. Remove load handling equipment only after mounting is complete.

6.1 When mounting with a bridge or shaft

WARNING

Risk of injury from moving parts at the flanged joint.

Exposed parts between drive and positioner can cause injuries.

• Keep range of action of moving parts free.

• Do not reach into the range of action of the flanged joint.

• Wear suitable protective clothing (e.g. safety shoes, safety gloves).

7 Disassembly

1. Switch off the electrical power supply.

2. Switch off the compressed air supply.

3. Drain all piping and disconnect all lines.

4. Disassemble unit in reverse order of installation.

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	KVZB

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo KVZB stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo SIED-M18NB-ZS-S-L Manual

20 August 2025

Festo SOEG-RT-M12-PS-K-2L Manual

20 August 2025

Festo VABD-S2-1-S-C Manual

20 August 2025

Festo SIED-M18B-ZO-S-L Manual

19 August 2025

Festo VACC-S18-120-K4-27-KS4ME Manual

19 August 2025

Festo VABS-S4-1S-G14-K2 Manual

19 August 2025

Festo P.BE-CP-CO-DE Manual

19 August 2025

Festo VABS-S4-2S-G18-B-K2 Manual

19 August 2025

Festo P.BE-CP-FB5-E-FR Manual

19 August 2025

Festo P.BE-CP-DN-DE Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Nokia CH-100 Manual

17 December 2025

Miele DKF 31-S Manual

17 December 2025

Aqprox appLS24 Manual

17 December 2025

Vaxcel T0440 Manual

17 December 2025

Georgia Pacific enMotion 59466A Manual

17 December 2025

Wine-Mate WM-8500SSDWC Manual

17 December 2025

TOTO TSU08W Manual

17 December 2025

Vaxcel T0702 Manual

17 December 2025

Wine-Mate WM-6500SSD Manual

17 December 2025

Wine-Mate WM-2500SSVWC Manual

17 December 2025