Festo PAML-CP-186-HP3-G114 Manual

Festo Ikke kategoriseret PAML-CP-186-HP3-G114

Læs gratis den danske manual til Festo PAML-CP-186-HP3-G114 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Festo PAML-CP-186-HP3-G114, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

PAML-CP/-MK-186

Sub-base/Module connector

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Deutschland

+49 711 347-0

www.festo.com

Assembly instructions

8161951

2021-10b

[8161953]

Translation of the original instructions

1 Applicable documents

All available documents for the product

è www.festo.com/sp.

2 Safety

2.1 Safety instructions

–Only use the product in its original condition without unauthorised modifica-

tions.

–Only use the product if it is in perfect technical condition.

–Take the weight of an individual device or a service unit into account.

Dependent on the design, a mounted service unit can weigh more than 100 kg.

–Under intended use the surface temperature may reach 60 °C. Allow the device

to cool down before working on it.

–Make sure the mounting surface is sufficiently strong for the maximum forces.

–Only use suitable mounting components.

–Mount the individual device or the service unit only on flat surfaces.

2.2 Intended use

–The sub-base PAML-CP serves as an adapter for the pneumatic connection and

for pipe mounting for in-line installation of service units.

–The module connector PAML-MK is used to connect two service units of the

same size.

2.3 Training of qualified personnel

Work on the product may only be carried out by qualified personnel who can eval-

uate the work and detect dangers. Personnel must have the relevant mechanical

training.

3 Additional Information

–Accessories è www.festo.com/catalogue.

4 Product Range Overview

4.1 Scope of delivery

Fig. 1: Sub-base PAML-CP

Front plate (1x)

Rear plate (1x)

Screw (8x)

Washer (8x)

O-ring (2x)

Fig. 2: Module connector PAML-MK

Screw (2x)

Front plate (1x)

O-ring (1x)

Rear plate (1x)

4.2 Not in scope of delivery

10 11

Fig.3

Electrical pressure regulator (1x)

PREL-186

Micro filter (1x)

PFML-186

5 Assembly

5.1 Mounting the connecting plates PAML-CP

Fig.4

1. Orient the front plate and the rear plate so the stamp number on the1 2

sub-base corresponds with the stamp number on the housing (1 to 1 and 2 to

2) and the mounting thread for wall mounting points to the rear.aB

2. Insert the O-rings in the slots provided.5

3. Position the front plate and the rear plate .1 2

4. Fasten the front plate and the rear plate to the service unit using four1 2

screws and four washers . Tightening torque: 27 Nm ± 15% 3 4

5. Comply with the maximum screw-in depth for the pipe connection.

ISO 228 Max. screw-in depth [mm]

G1/2 12

G1 1/4 20

G1 1/2 22

G2 24

G2 1/2 26

5.2 Assembly of the module connector PAML-MK

Fig.5

1. Note the flow direction from 1 to 2. The numbers on the product housingaC

serve as orientation.

2. Insert the retaining screws through the holes in the front plate .6 7

3. Place the seal between the service units.8

4. Place the front plate and the rear plate in the slots of the service units.7 9

5. Tighten the screws . Tightening torque: 40 Nm ± 25% 6

5.3 Wall mounting

The M12 threads on the sub-bases and module connectors can be used to mount

individual devices or service units on the wall or a machine frame.

The grid dimension width for distributor block PMBL-186-HP3 is 93 mm.

The grid dimension width between the sub-bases and module connectors is

186 mm as standard, and the hole spacing is 145 mm in height.

Fig.6

•Fasten all sub-bases and module connectors with two screws M12 each.aD

The screw-in depth must be at least 15 mm and maximum 18 mm. Maximum

tightening torque: 42 Nm

6 Disassembly

1. Depressurise the system.

2. Check the surface temperature of the device. If necessary, let the device cool

down.

3. Remove the existing service unit string.

7 Technical data

PAML -CP -MK

Operating pressure [MPa] 0 … 5

[bar] 0 … 50

[psi] 0 … 725

Temperature of medium [°C] +5 … +60

Ambient temperature [°C] +5 … +60

Tab. 1: Technical data

Produkt Specifikationer

Mærke:	Festo
Kategori:	Ikke kategoriseret
Model:	PAML-CP-186-HP3-G114

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo PAML-CP-186-HP3-G114 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Festo Manualer

Festo KYC-63 Manual

9 Juli 2025

Festo NEBM-L10G14-EH-5-Q7N-LE12 Manual

8 Juli 2025

Festo CPX-E-8DO Manual

8 Juli 2025

Festo CRDSNU-20-80-P-A Manual

8 Juli 2025

Festo CRDSNU-16-10-P-A Manual

8 Juli 2025

Festo CPV-SC-FB-VI Manual

7 Juli 2025

Festo CRDSNU-B-16-50-P-A-MG-A1 Manual

7 Juli 2025

Festo NEBM-L10G14-EH-10-Q7N-LE12 Manual

7 Juli 2025

Festo CPX-CTEL-4-M12-5POL Manual

7 Juli 2025

Festo CRDSNU-B-25-25-PPS-A-MG-A1 Manual

7 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Goal Zero TANK PRO 4000 Manual

11 Juli 2025

PAC CAM-GM51 Manual

11 Juli 2025

Yamazen CSWR-3080 Manual

11 Juli 2025

Vivax BO-608FAHTD X Manual

11 Juli 2025

Phoenix Contact IFS-CONFSTICK Manual

11 Juli 2025

Parkside PDNB 6.3 B2 Manual

11 Juli 2025

Ikea KALLSJÖN 004.863.51 Manual

11 Juli 2025

Ikea GRILLSKÄR 205.232.77 Manual

11 Juli 2025

Asus Q670EM-IM-A Manual

11 Juli 2025

Nebula Mars Manual

11 Juli 2025