Fisher & Paykel 23983 Manual

Fisher & Paykel Ikke kategoriseret 23983

Læs gratis den danske manual til Fisher & Paykel 23983 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 54 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 27.5 anmeldelser. Har du et spørgsmål om Fisher & Paykel 23983, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Refrigerator Surround Kit

Installation instructions

E402B, E442B, E522B, RF610A, RF540, RF522A models NZ AU GB AE HK SG IE US CA EU CN IN

Important!

SAVE THESE INSTRUCTIONS

The model shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website

www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

3 Parts suPPlied

Top trim (x 1)

Side trim (x 2)

Bottom trim

(x 1)

Side trim

brackets (x 10)

Side trim

brackets (x 4)

Side trim centre

brackets (x 6)

Top trim brackets:

– Single

refrigerator kits

(2 x brackets)

– Side by Side kits

(3 x brackets)

Screw type A:

#8 x 12 Pozi

Drive CSK (x 26)

Long screws

10 x 75 CSK PH

P/no SP0207

(x 2)

Floor stops

P/no 460912

(x 2)

Washers

4 x 11 x 1mm

(x 2)

6 seCure side

trim braCkets

Locate the ten side trim brackets.

Position five brackets to the left hand side of

the cabinet and the remaining five brackets to

the right hand side of the cabinet.

Brackets should be evenly spaced down each

side (see diagram 3a/b). Secure each of these

brackets with the two screws provided.

Care must be taken to line up the front edge

of the brackets with the leading edges of

thecabinet.

Diagram 3b

Diagram 3a

7 seCure Floor stoPs

Two floor stops are supplied to prevent the refrigerator from being pushed too far back into the cavity.

These are mounted on the base or floor at a distances of 688mm (27") from the face front edge of the

trim kit.

688 mm

150 mm

Diagram 4

4 Cabinetry dimensions

Diagram 1a

Cabinet at floorlevel

Diagram 1b

Cabinet above toekick

C1C2

Installation diagrams for illustration purposes only Diagram 1

Cutout dimensions – flush to edge of door (mm / inches)

635 (25") model

680 (26 /") model

790 (31 /") model

900 (35 /") model

635 (25") model

+ 635 (25") model

680 (26 /") model

+ 680 (26 /") model

790 (31 /") model

+ 790 (31 /") model

Awidth 807 (31 ⁄”) 852 (33 ⁄”) 962 (37 ⁄”) 1072 (42 ⁄”) 1467 (57 ⁄”) 1557 (61 ⁄”) 1777 (70”)

Bdepth* 700 (27 ⁄”) 700 (27 ⁄”) 700 (27 ⁄”) 700 (27 ⁄”) 700 (27 ⁄”) 700 (27 ⁄”) 700 (27 ⁄”)

C1height** 1790 (70 /") 1790 (70 /") 1790 (70 /") 1875 (73  ⁄ ") 1790 (70 /") 1790 (70 /") 1790 (70 /")

C2height*** 1806 (71 /") 1806 (71 /") 1806 (71 /") 1891 (74 /") 1806 (71 /") 1806 (71 /") 1806 (71 /")

Dair vent

depth 200 (8”) 200 (8”) 200 (8”) 200 (8”) 200 (8”) 200 (8”) 200 (8”)

Eair vent

width 502 (19 /") 547 (21 ⁄") 657 (25 /") 767 (30 /") 1162 (45 ⁄") 1252 (49 ⁄") 1472 (58")

* Depth is a minimum requirement

** Height is without 16mm MDF packer

*** Height is with 16mm MDF packer

Cut out dimensions above are to be used as dimensions.minimum

5 seCure toP

trim braCkets

Locate the two/three top trimbrackets.

For the Side By Side Refrigerator kits, one

bracket is to be screwed in the top centre of the

cabinet, secure the top bracket with two of the

screws (Type A, #8 x 12 PoziDrive CSK).

For all other kits, the two brackets are to be

secured on either side, by two screws which are

mounted from the side (seediagram 2).

Looking at the front of the product, place the

top brackets on top of the woodencabinet.

Care must be taken to line up the top front

edge of the brackets with the leading edge of

the cabinet.

Hint: Holes should be drilled in the centre of

the slot in the brackets to allow for adjustment.

End bracket Centre bracket

Diagram 2

1 reFrigerator surround kit

This kit is designed to be used with models with a cabinet height of

between: 1695mm – 1806mm (66 ¾”–71 /”) with curved or flat door styling.

Youcan find the part number for each installation type in Section 10.

To give the most integrated look, the kitchen cabinetry should be flush with

the front of the refrigerator door.

Tools required (not included)

No. 2 drill bit – long

Electric drill

Phillips screwdriver

1 x 16mm ( inch) piece of MDF the same size as the base of the cavity ⁄

(optional). Not needed if refrigerator cabinet is sitting directly on the floor

and not on raised toe kickarea

Joiner kit (part number 819264) required if joining two refrigerators side by side

Before starting

All dimensions are internal or cut out dimensions.

The refrigerator can be installed:

1. In a cavity with a toe kick under the product with the bottom trim fitted to the base (diagram 1b/5).

2. In a cavity with 16mm panel under the product with the bottom trim fitted to the panel

(diagram 1a/6).

3. In a cavity where the product is at floor level with no bottom trim (diagram 1a).

4. Check whether your fridge has hinges concealed by the front of the fridge door. If unsure refer to

page 2 note*** for instructions.

2 getting started

Check that the internal Cupboard Cavity dimensions are correct (see diagram 1a/b).

Unpack the refrigerator and/or freezer cabinets from their separate delivery cartons (see individual

cartons for unpacking procedures).

Ensure the floor and/or the cupboards are protected from damage during the unpacking and

assembly of the cabinets.

Check the refrigerator and freezer doors are hinged on the desired side.

Check that the kit is complete (refer to Parts Supplied in section 3).

Note 1: Due to the size of the refrigerator cabinets, it is essential that assembly of the kit be undertaken

with a minimum of two able-bodied persons.

Note 2: It is important to include adequate venting to the top of the cabinet to ensure the efficient

operation of the refrigerator.

Note 3: The installation of the cabinet or cabinets can be at floor level as shown in diagram 1a or installed

above the toe kick board as in diagram 1b.

Note 4: Rollers and feet must be fitted.

Note 5: Cabinets installed above the toe kit should have a floor base constructed to support the total

weight of the loaded cabinet or cabinets placed on it.

The placement of the 16mm ( ") MDF or plywood under the cabinet or cabinets on either installation /

type is to allow the fitment of the bottom trim that covers it. It is optional.

Produkt Specifikationer

Mærke:	Fisher & Paykel
Kategori:	Ikke kategoriseret
Model:	23983
Type:	Husholdningsartikel, sæt
Bredde:	852 mm
Dybde:	700 mm
Højde:	1790 mm
Velegnet til:	Køleskab
Produktfarve:	Rustfrit stål
Materiale:	Rustfrit stål
Enhedstype:	Køleskab
Mærke kompatibilitet:	Fisher & Paykel