Fisher & Paykel RF522WDLX4 Manual

Fisher & Paykel Køleskab RF522WDLX4

Læs gratis den danske manual til Fisher & Paykel RF522WDLX4 (3 sider) i kategorien Køleskab. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 23 anmeldelser. Har du et spørgsmål om Fisher & Paykel RF522WDLX4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

continued >

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model

and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

1 Check that the internal cabinetry dimensions are correct (see Diagram 1a/b).

2 Unpack the refrigerator as per instructions on carton.

IMPORTANT!

Due to the size of the refrigerator(s), it is essential that assembly of the surround kit be undertaken with a minimum of two able-

bodied persons.

It is important to include adequate venting to the top of the refrigerator, to ensure efficient operation.

The installation of the refrigerator(s) can be at floor level as shown in Diagram 1a or installed above the toe kick board as in

Diagram1b.

Rollers and feet must be fitted.

Refrigerators installed above the toe kit should have a floor base constructed to support the total weight of the loaded

refrigerator(s) placed on it.

The placement of the 16mm MDF or plywood under the refrigerator(s) on either installation type is to allow the fitment of the bottom

trim that covers it. It is optional.

GETTING STARTED

This kit is designed to be used with models with a refrigerator height of between: 1695 – 1806mm with curved or flat door styling.

You can find the part number for each installation in Section 2.

To give the most integrated look, the kitchen cabinetry should be flush with the front of the refrigerator door.

Tools required (not included)

No. 2 drill bit – long.

Electric drill.

Phillips screwdriver.

1 x 16mm piece of MDF the same size as the base of the cavity (optional). Not needed if refrigerator is sitting

directly on the floor and not on raised toe kickarea.

Joiner kit (part number 819264) required if joining two refrigerators side by side.

REFRIGERATOR SURROUND KIT

E402B

RF402B

E402B

RF402B

E402B

RF402B

E442B

RF442B

E442B

RF442B

E442B

RF442B

E522B

RF522B

RF522W

E522B

RF522B

RF522W

E522B

RF522B

RF522W

RF522A RF540A

RF610A

REFRIGERATOR MODEL 1 X E402B

1 X RF402B

2 X E402B

2 X RF402B

1 X E442B

1 X RF442B

2 X E442B

2 X RF442B

1 X E522B

1 X RF522B

1 X RF522W

2 X E522B

2 X RF522B

2 X RF522W

1 X RF522A

(French door model)

1 X RF540A

1 X RF610A

(French door model)

CAVITY DIMENSIONS (Flush to edge of door) mm mm mm mm mm mm mm mm

AWidth 807 10721467 1557 962 1777 962852

BDepth* 700 700 700 700 700 700 700 700

C 1Height** 1790 1790 1790 1790 1790 1790 1790 1875

C 2Height*** 1806 1806 1806 1806 1806 1806 1806 1891

DAir vent depth 200 200 200 200 200 200 200 200

EAir vent width 502 1162 1252547 657 6571472 767

KIT PART NUMBERS LH RH LH RH LH RH

Brushed Stainless 24371 24372 24373 24375 2437624374 24377 24381 2438024378 24379

Plus Joiner Kit 819264 819264 819264

* Depth is a minimum requirement.

** Height is without 16mm MDF packer.

*** Height is with 16mm MDF packer.

Cavity dimensions above are to be used as dimensions.minimum

Diagram 1a

Refrigerator at floorlevel

Diagram 1b

Refrigerator above toekick

Diagram 1

KIT PART NUMBERS AND CAVITY DIMENSIONS TABLE

All dimensions are internal or cavity dimensions.

The refrigerator can be installed:

1 In a cavity with 16mm panel (bottom trim attached), or in a cavity where the product

is at floor level (no bottom trim). (Diagram 1a).

2 In a cavity with a toe kick under the product with the bottom trim fitted to the base

(Diagram 1b).

3 Check whether your fridge has hinges concealed by the front of the fridge door.

For refrigerators / freezers where the hinge is not concealed by the door refer to

spare parts for the correct kit number. 820413 D should list non concealed number kit.

BEFORE INSTALLATION

Concealed hinge Non concealed hinge

NZ AU GB AE HK SG IE EU CN IN

REFRIGERATOR SURROUND KIT

INSTALLATION GUIDE

E402B, RF402B, E442B, RF442B, E522B, RF522B, RF522W, RF522A, RF540A & RF610A models

Before you call for service or assistance ...

Check the things you can do yourself. Refer to the Installation Instructions and your User Guide. Checkthat:

1 Your product is correctly installed.

2 You are familiar with its normal operation.

3 You have read the ‘Troubleshooting’ section at the back of the User Guide.

If after checking these points you still need assistance or parts, please contact your Fisher & Paykel trained and supported service

technician, Customer Care Centre, or contact us through our website www.fisherpaykel.com

FURTHER INFORMATION

TRIM INSTALLATION

The bottom trim is designed to cover the front edge of the floor base panel of the

refrigerator. This trim can be installed on a raised toe kick (Diagram 1a) or toe kick

below the refrigerator (Diagram 1b)

Remembering that if this trim is to be used with the refrigerator at floor level the

cavity dimensions will need to have 16mm added to its height to allow for the bottom

trim to be fitted. Note this trim is optional on this type ofinstallation. If used with a

raised toe kick the 16mm packer should be part of the base (Diagram5). Therefore

16mm is not required to be added to the height dimension.

1 If used place the 16mm piece of plywood or with bottom trim fitted into the cavity

(Diagram 5 or 6). Note: the piece should be the same size as the base of the cavity.

2 Remove protective coating film from surround trim.

3 To install the surrounds, first clip in the top surround. Ensure the locator strips at the

rear of the top brackets clip into the rear of the top trim.

4 Clip both side trims into place starting from the front refrigerator edge.

16mm plywood or

MDF board insert

Part of base

Diagram 5

SECURE FLOOR STOPS

Two floor stops are supplied to prevent the

refrigerator from being pushed too far back into

the cavity. These are mounted on the base or

floor at a distance of 688mm from the face front

edge of the trim kit.

MOVE INTO CAVITY

If installing two refrigerators/freezers side by side a joiner kit

is required. Refer to these instructions and fit joiner kit before

pushing refrigerator into place, see Diagram 6.

1 Plug refrigerator into electrical socket, run water connection to

refrigerator if required (Ice & Water models only).

2 Gently install refrigerator into cabinetry making sure it is

centred within the surround trim.

3 The front of the refrigerator door should be flush with the front

of the cabinetry to obtain anintegratedlook.

4 Ensure the front levelling feet are adjusted to take the load of

the fridge and keep it in place.

Optional

Diagram 6

PARTS SUPPLIED

Top trim (1)

Side trim (2)

Bottom trim (1)

Top trim brackets:

– Single refrigerator kits

(2 brackets)

– Side by Side kits

(3 brackets)

Side trim

centre brackets

(6)

Screw type A:

#8 x 12 Pozi Drive CSK

(26)

Long screws

10 x 75 CSK PH

Part number: SP0207

(2)

Floor stops

Part number: 460912

(2)

Washers

4 x 11 x 1mm

(2)

Side trim brackets

(10)

Side trim brackets

(4)

SECURE SIDE TRIMBRACKETS

Locate the ten side trim brackets.

Position five brackets to the left hand side of the

cabinetry and the remaining five brackets to the right

hand side of the cabinetry.

Brackets should be evenly spaced down each side

(see Diagram 3a/b). Secure each of these brackets

with the two screws provided.

Care must be taken to line up the front edge of the

brackets with the leading edges of thecabinetry.

SECURE TOP TRIMBRACKETS

Locate the two/three top trimbrackets.

For the side by side refrigerator kits, one bracket is to be

screwed in the top centre of the cabinetry, secure the top

bracket with two of the screws (Type A, #8 x 12 PoziDrive

CSK) (see Diagram 2a).

For all other kits, the two brackets are to be secured on

either side, by two screws which are mounted from the side

(seeDiagram 2b).

Looking at the front of the refrigerator, place the top brackets

on top of the woodencabinetry.

Care must be taken to line up the top front edge of the

brackets with the leading edge of the cabinetry.

Hint: holes should be drilled in the centre of the slot in the

brackets to allow for adjustment. Diagram 2

Diagram 2b

End bracket

Diagram 2a

Centre bracket

Diagram 3bDiagram 3a

150mm

688mm

Diagram 4

84 4 144 C 10. 17

Produkt Specifikationer

Mærke:	Fisher & Paykel
Kategori:	Køleskab
Model:	RF522WDLX4

Har du brug for hjælp?

Hvis du har brug for hjælp til Fisher & Paykel RF522WDLX4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Køleskab Fisher & Paykel Manualer

Fisher & Paykel RS7621SLHEI Manual

10 Juli 2025

Fisher & Paykel RS6121SRK2 Manual

7 Juli 2025

Fisher & Paykel RF610ANUB7 Manual

28 December 2024

Fisher & Paykel RF610ADUSB6 Manual

27 September 2024

Fisher & Paykel RX628DW1 Manual

23 September 2024

Fisher & Paykel RX628DX1 Manual

23 September 2024

Fisher & Paykel RS7621FRJK2 Manual

18 September 2024

Fisher & Paykel E402BRXFD4 Manual

14 September 2024

Fisher & Paykel RF610ADUSB7 Manual

6 September 2024

Fisher & Paykel RF610ADUSX6 Manual

6 September 2024

Køleskab Manualer

Nyeste Køleskab Manualer

Hoshizaki Valiance VSR48A Manual

29 Juli 2025

Hoshizaki Steelheart SR72A-30MD6 Manual

29 Juli 2025

Frigidaire GRTE1834VW Manual

29 Juli 2025

Klarstein Irene Mini Manual

29 Juli 2025

Frigidaire FRMS274TAV Manual

29 Juli 2025

Hoshizaki Steelheart UR27B-LPD2 Manual

29 Juli 2025

Hoshizaki Steelheart ULF46B Manual

29 Juli 2025

Indesit IB55 732 W UK Manual

29 Juli 2025

Midea MRF32I6BST Manual

29 Juli 2025

AEG TC7MS181CF Manual

29 Juli 2025