Fluke 700 PMP Manual

Fluke Pomp 700 PMP

Læs gratis den danske manual til Fluke 700 PMP (2 sider) i kategorien Pomp. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Fluke 700 PMP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

700PMP

Precision Pressure Pump

Instruction Sheet

Introduction

The Fluke 700PMP is a tube type, cylindrical

shaped hand pump with a "T" handle at the

compressor end and a round knob at the volume

adjust end. The overall length is between 11.5"

(full extension) and 8.5" (fully collapsed). The

pump incorporates a needle valve for venting

and a volume adjust vernier for precision

adjustment of pressure.

Pressure connections are made through one 1/8"

NPT internally threaded fitting. The pump is

small in size, lightweight and ruggedly

constructed to withstand typical field use.

Operating Instructions

Producing Pressure

1. Connect the pump's port to the instrument to

be calibrated or checked. Use small-diameter

tubing as short in length as possible (this will

maximize the pressure adjustment range).

2. Set the FINE ADJUST knob to the full

counterclockwise position.

3. Turn the bleed valve knob fully

counterclockwise to relieve all system

pressure and zero any measuring devices.

4. Turn the bleed valve knob fully clockwise to

close.

5. Repeatedly move the "T" handle in and out to

generate the desired pressure.

6. Use the FINE ADJUST knob to bring up the

pressure to the precise level.

7. Use the BLEED VALVE to lower the pressure

from the pressure generated. Opening the

BLEED VALVE 1/4 turn will lower the

pressure very gradually. Opening it 1/2 turn

will release the pressure faster and opening it

3/4 turn will quickly and safely release all the

pressure in the system.

9Warning

It is imperative that all system

pressure is relieved prior to making

any connections or disconnections.

Failure to relieve system pressure

could result in serious personal

injury or equipment damage. Even

nominal pressure values can

generate extreme force if fitting or

tubing failure occurs due to improper

installation or usage. Since the pump

is capable of generating pressures

exceeding 100 psig/70 bar, it is

important that all pressure

connections and test procedures be

done by qualified service personnel,

according to standard engineering

practices, to prevent possible

personal injury or equipment

damage.

Connections

To install a pressure fitting in the pump:

1. Turn the BLEED VALVE counterclockwise to

bleed any pressure.

2. Use a 5/8" open-end wrench on the input port

to prevent it from rotating while tightening the

supply fitting with a 5/8" open-end wrench.

Leak Prevention and Detection

In order to obtain maximum pressure indication

stability, leaks must be avoided. It is strongly

recommended that either Teflon® tape or

commercial pipe sealant is used at all tapered

fittings and connections. If Teflon® tape is used,

care must be taken that the proper amount is

applied. Excessive tape may fray and cause

plugging of relief valves orifices, nozzles, etc.

Overuse of pipe sealant may cause similar

problems.

Produkt Specifikationer

Mærke:	Fluke
Kategori:	Pomp
Model:	700 PMP

Har du brug for hjælp?

Hvis du har brug for hjælp til Fluke 700 PMP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Pomp Fluke Manualer

Fluke 700HTH-1 Manual

22 August 2024

Fluke 730HTP70M Manual

14 August 2024

Fluke 730PTP10M Manual

23 Juli 2024

Fluke 730LTP40K Manual

23 Juli 2024

Fluke 700 PMP Manual

22 Juli 2024

Pomp Manualer

Nyeste Pomp Manualer

Little Giant OPWG-29 Manual

1 April 2025

Interphone Air Pump 3000 Manual

1 April 2025

Grundfos UPS 20-60 N 150 Manual

1 April 2025

Grundfos UPS 40-50 FN 250 Manual

1 April 2025

Grundfos MTA 120-280 Manual

1 April 2025

Grundfos DMX 860-5 Manual

1 April 2025

Grundfos UPM4 Manual

1 April 2025

Grundfos DMH 880-10 Manual

1 April 2025

Grundfos MTA 200-280 Manual

1 April 2025

Grundfos MTSE 40-66 Manual

1 April 2025