Fluke T130 Manual

Fluke Måleudstyr T130

Læs gratis den danske manual til Fluke T130 (3 sider) i kategorien Måleudstyr. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Fluke T130, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

T90/T110VDE/

T130VDE/T150VDE

Voltage/Continuity Tester

Instruction Sheet

Introduction

The Fluke T90/T110VDE/T130VDE/T150VDE

Electrical Testers (the Tester or Product) are

voltage and continuity testers with a rotary eld

indication (T110VDE/T130VDE/T150VDE only).

Their primary use is for test and measurement in

industrial, commercial, and household environments.

This Product complies with the most recent safety

standards for safe, reliable test and measurement.

The xed test probe cover prevents the risk of injury

when you move the instrument.

To Contact Fluke

Fluke Corporation operates worldwide. For local

contact information, go to our website: www.uke.com

To register your product, view, print, or download

the latest manual or manual supplement, go to our

website.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

+1-425-446-5500

uke-info@uke.com

Safety Information

 Warning

To prevent possible electrical shock, re, or

personal injury:

●Read all safety Information before you use the

Product.

● Use the Product only as specied, or the

protection supplied by the Product can be

compromised.

● Measure a known voltage rst to make sure

that the Product operates correctly.

●Do not apply more than the rated voltage,

between the terminals or between each

terminal and earth ground.

PN 3928126

October 2011, Rev. 3, 3/21

Specications are subject to change without notice. All product

names are trademarks of their respective companies.

● Limit operation to the specied measurement

category or voltage ratings.

●Do not work alone.

●Comply with local and national safety codes.

Use personal protective equipment (approved

rubber gloves, face protection, and ame-

resistant clothes) to prevent shock and arc

blast injury where hazardous live conductors

are exposed.

●Do not use the Product around explosive gas,

vapor, or in damp or wet environments.

●Do not use and disable the Product if it is

damaged.

●Do not use the Product if it operates

incorrectly.

● Keep ngers behind the nger guards on the

probes.

●Do not use the Product if the test leads are

damaged.

●Examine the case before you use the Product.

Look for cracks or missing plastic.

●The battery door must be closed and fastened

before you operate the Product.

●Replace the batteries when the low battery

indicator shows to prevent incorrect

measurements.

●Repair the Product before use if the battery

leaks.

●For use by competent persons. Anyone

using this Product should be knowledgeable

and trained about the risks involved with

measuring voltage, especially in an industrial

setting, and the importance of taking safety

precautions and of testing the Product before

and after using it to ensure that it is in good

working condition.

Symbols

These symbols are on the Tester or in this instruction

sheet.

Symbol Explanation

Important information. Consult the

instruction sheet.

Hazardous Voltage.

¥Suitable for live working.

This product complies with the WEEE

Directive (2002/96/EC) marking

requirements. The a󰀩xed label indicates

that you must not discard this electrical/

electronic product in domestic household

waste. Product Category: With reference

to the equipment types in the WEEE

Directive Annex I, this product is classed

as category 9 "Monitoring and Control

Instrumentation" product. Do not dispose

of this product as unsorted municipal

waste. Go to Fluke’s website for recycling

information.

Symbol Explanation

Conforms to European Union Directives.

§VDE Association for Electrical, Electronic

& Information Technologies; following

rules of "Geprüfte Sicherheit."

CAT III Measurement Category III is applicable to

test and measuring circuits connected to

the distribution part of the building’s low-

voltage MAINS installation.

CAT IV Measurement Category IV is applicable

to test and measuring circuits connected

at the source of the building’s low-voltage

MAINS installation.

Accessories

The Tester is supplied with accessories.

Part Number Accessory

4083642 GS38 Probe Tip Sheath

4083656 4.2 mm ∅ Probe Extensions

4111533 H15 Belt Holster (sold separately)

4111540 C150 Zippered Soft Carrying Case

(sold separately)

Figure 1 shows the Probe Tip Protector Cap. This

multifunctional accessory is useful for tests and

storage of di󰀨erent accessories. (The Probe

Extensions are stored in the Probe Tip Protector Cap

before shipment.)

Storage area for Probe Tip Sheaths

Storage area for 4.2 mm ∅ Probe Extensions



Earth-pin safety-socket opener for UK

sockets (press opener into socket to release

safety covers, see Figure 2)

Storage area for probes when not in use

Quick Reference

Use the pushbuttons to turn the functions on or o󰀨.

See the list that follows for a quick reference to each

of these pushbuttons.

Pushbutton Description

Push to turn torch light on or o󰀨

(T110VDE, T130VDE, T150VDE).

To save battery power the

function automatically turns o󰀨

after 30 seconds.

Push to hold the value that shows

in the LCD in volt and resistance

measurements. Push again

to turn HOLD o󰀨 (T130VDE,

T150VDE).

To save battery power the

function automatically turns o󰀨

after 30 seconds.

Push this button on each of

the probes at the same time to

start the test for low impedance

switchable load.

Push and hold for 2 seconds to

turn the resistance measurement

on or o󰀨 (T150VDE only).

To save battery power, the

function automatically turns o󰀨

after 30 seconds.

Figure 3 illustrates how to store and retrieve the tip

accessories from the cap.

For storage, push Probe Tip Sheath into

place.

To retrieve, rmly push probe tip into Probe

Tip Sheath.

Pull on probe handle to remove Probe Tip

Sheath.

For storage, push 4.2 mm Probe ∅

Extensions into place.

To retrieve, rmly push probe tip into Probe

Extensions. Twist 1/4 turn.

Pull on probe handle to remove Probe

Extensions. Continue to twist until tip is tight.

1/4

Produkt Specifikationer

Mærke:	Fluke
Kategori:	Måleudstyr
Model:	T130

Har du brug for hjælp?

Hvis du har brug for hjælp til Fluke T130 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måleudstyr Fluke Manualer

Fluke 323 True RMS Manual

14 September 2024

Fluke FEV350 Manual

3 September 2024

Fluke 319 Manual

22 August 2024

Fluke T150/VDE Manual

22 August 2024

30 Juli 2024

30 Juli 2024

30 Juli 2024

29 Juli 2024

29 Juli 2024

28 Juli 2024

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025