Fujitsu AXGA24AAT Manual

Fujitsu Aircondition AXGA24AAT

Læs nedenfor 📖 manual på dansk for Fujitsu AXGA24AAT (16 sider) i kategorien Aircondition. Denne guide var nyttig for 41 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/16
ROOM AIR CONDITIONER
}
AX SERIES
18
22
24
50 Hz MODEL
PART No. 9352970023-03
1
POWER SUPPLY
WARNING
(1) In order to enable efficient and trouble-free operation of your air conditioner, connect the power plug of your air conditioner
through an exclusive circuit, having a time delay fuse, to the correct power supply describe on the rating plate.
(2) Please connect the “L” line of the power supply cord to the “Live” terminal of the power outlet, and the Earth line (Green and
Yellow) to the Earth terminal. The remaining line should be connected to the Neutral terminal of the power outlet.
(3) If the power supply cord of this appliance is damaged, it should only be replaced by the authorized service personnel, since
special purpose tools and specified cord are required.
2
INSTALLATION
Condenser Air
Inlet Both Sides
Evaporator Air Outlet
Condenser Air Outlet
Front Rear
at least 60 cm
top at least 20 cm
1. Installation location
(1) Select a place where cool air emitted from the Air Condi-
tioner circulates evenly, reaching every part of the room.
Make sure that no obstacles both inside and outside the
room prevent the air flow.
WARNING
In the work of this item, the authorized service personnel
should work.
(2) Where practicable, locate the air conditioner with the lower
edge of the cabinet approximately 0.75 m (29.5") to 1.5 m
(59") from the floor. This usually gives the optimum air circu-
lation pattern within the room for cooling and heating.
(3) Mounting must be strong enough to support the weight of
the air conditioner with sufficient rigidity to prevent vibration
being transmitted to windows and the like.
(4) Where the rear and sides of the unit are unobstructed.
3
2. The Dimension of opening for mounting
Fit the small urethane foam
into the space between the
cabinet and the unit.
3. Installation process
(1) Remove the front panel.
(2) Slide out the unit from the cabinet.
(3) Fix the cabinet to the timber frame using nails or screws so
that the condenser air inlet louvre is placed outside the wall.
If required, support the cabinet in the wall with brackets and
completely weather seal any gap between the cabinet and
the wall.
(4) Push the unit completely back into the cabinet.
(5) Next, fit the attached urethane foam into the space between
the cabinet and the bottom of the unit with a screw driver to
seal the room inside from the outside.
(6) Refit the front panel.
Note: When constructing a timber frame, arrange so that the
outside rear of the air conditioner is between 0.5 1 cm
lower than the front of the unit. This allows condensed
water to drain off outside the room. If the inside of the air
conditioner is lower, condensed water and rain may flow
into the room.
670 673 (mm)
455 460 (mm)
4
4. Typical installation
Front panel
Condenser air inlet louvres
Fit flashing or insert caulking compound
behind top outside architrave.
Recommended architrave 57 mm (2-1/4")
× 13 mm (1/2") tapering to 8 mm (5/16")
typical all round on front and rear of unit.
Timber frame — typical all round on
front and rear of unit.
50 mm (2") × 6 mm (1/4") sponge rubber
strip typical all round on front and rear
of unit.
Condenser air inlet louvres must
be completely clear of outside ar-
chitrave surface.
If required attach the cabinet support
brackets (not supplied) to the cabinet and the wall.


Produkt Specifikationer

Mærke: Fujitsu
Kategori: Aircondition
Model: AXGA24AAT

Har du brug for hjælp?

Hvis du har brug for hjælp til Fujitsu AXGA24AAT stil et spørgsmål nedenfor, og andre brugere vil svare dig




Aircondition Fujitsu Manualer

Aircondition Manualer

Nyeste Aircondition Manualer