Fujitsu DL3600 Manual

Fujitsu Printer DL3600

Læs gratis den danske manual til Fujitsu DL3600 (2 sider) i kategorien Printer. Denne vejledning er vurderet som hjælpsom af 61 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 31 anmeldelser. Har du et spørgsmål om Fujitsu DL3600, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

OSE Fujitsu DL3600

Print method 24-pin impact dot matrix

Print speed 300 cps @ 10 cpi, 360 cps @ 12 cpi, high-speed draft;

90 cps @ 10 cpi, 108 cps @ 12 cpi, letter quality

Resolution 360 dpi

Fonts Eight resident fonts plus downloadable fonts and optional

plug-in font cards

Paper Handling Rear push tractor feed, friction feed. Up to five-part

forms, maximum thickness 0.33 mm

Interfaces CENTRONICS parallel or RS-232C serial

Emulations Fujitsu DPL24C PLUS, IBM Proprinter XL24, Epson

LQ-2500 and LQ-2550

Options CENTRONICS parallel and RS-232C serial interface, cut

sheet feeder, font and emulation cards, color kit

Control Panel

POWER light: Indicates printer is on.

ONLINE light: Indicates printer is ready to receive data.

PAPER OUT light: Indicates printer is out of paper.

LETTER and DRAFT lights: Indicate which print quality, letter or draft, is

selected.

FONT1 and FONT2 lights: Indicate which user-defined font/pitch combination

is selected.

MENU1 and MENU2 lights: Indicate which user-defined print feature set is

selected.

ONLINE key: Press to toggle printer online and offline.

FF key: Press to advance continuous feed paper one page or to eject a single

sheet. If PAPER OUT light is on, press to load paper to top of-form.

LF key: Press to advance paper one line.

TEAR OFF key: Press to advance continuous feed paper to the tear-off edge.

After tearing off paper, press any key to retract forms to top-of-form.

MODE key: With the printer offline, press to cycle between the LETTER/DRAFT,

FONT1/FONT2 and MENU1/MENU2 option pairs. An option pair is active when one

light is on and the other is flashing. On steadily indicates an option is selected;

flashing indicates an option is not selected. Press FF or LF key to select left-hand

or right-hand option, respectively. To return to normal mode, continue pressing

MODE key until no option pair lights are flashing. To return parameters to factory

default settings, hold MODE and LF keys while turning on printer. Continue holding

keys until printer beeps.

LOAD/UNLOAD key: Press to advance paper to top of form or to retract con-

tinuous feed paper to park position.

Self-test

Turn on printer while holding FF key. Continue holding FF key until printer beeps.

The firmware version, resident emulations and a continuous ASCII pattern is printed.

To pause self-test or hex dump, press MODE or LF key. To resume, press MODE

or LF key again. To terminate, press ONLINE key.

Hex dump

Turn on printer while holding FF and LF keys.

Printer Configuration

The printer is configured through the setup mode. Load continuous feed paper and

turn on printer while holding MODE key. Continue holding MODE key until the

printer beeps. Upon entering setup mode, the function menu and instructions for

using the setup mode are printed. Upon selecting a function that contains items and

options, that function's first item and its options are printed. Each function is summa-

rized below. *Denotes default settings.

SAVE&END - Select to save any changes made in setup mode and exit setup

mode. To exit setup mode without saving changes, turn printer off.

PANEL - Assigns a font and pitch to FONT1 and FONT2 and regular or high-

speed draft to DRAFT on control panel.

<DRAFT> - DRAFT *, HI-DRFT

<FONT1> - 1COUR 10 *, PRSTG12, COMPRSD, BOLDFCE, PICA 10,

CORRESP, [names from font card] DOWNLD0, DOWNLD1

<F1PITCH> - ## CPI (default 10 cpi), PROP SP

<FONT2> - (Same as FONT1 except default = PRSTG12)

<QUALITY> - LETTER *, REPORT, DRAFT, HI-DRAFT

<F2PITCH> - ## CPI (default 12 cpi), PROP SP

MENU1 and MENU2 - Assigns print features to MENU1 and MENU2 on control

panel. Items and options for MENU1 and MENU2 are identical.

<EMULATE, - DPL24C *, IBMXL24, LQ2500, LQ2550, names from emulation

card‘

<FONT> - COUR 10 *, PRSTG12, COMPRSD, BOLDFCE, PICA 10, CORRESP,

names from font card‘ DOWNLD0, DOWNLD1

<QUALITY> - LETTER *, REPORT, DRAFT, HI-DRFT

<PITCH> - # CPI (default 10 cpi), PROP SP

<LINE SP> - ## LPI (default 6 Ipi)3

<CHAR-W(idth)> - NORMAL, 2TIMES, 4TIMES (i)

<CHAR-H(eight)> - NORMAL, 2TIMES, 4TIMES (i)

<ATTRIB> - NONE, ITALICS (i), CONDNSD (i), SHADOW, BOLD

<PAGE LG> - ## IN (default 11 inches)

<COLOR> - AUTOSEL (software makes selection), BLACK, YELLOW, MAGENTA,

CYAN

<LFT-END> - ## COLM (specifies starting column of left margin, default 1)

<TOP-MRG> - ## LINE (specifies top margin, default 1)

<LANGUAGE> - USA *, UK, GERMAN, FRENCH, ITALIAN, SPANISH, SWEDISH,

FINNISH, DANISH1, DANISH2, PAGE### ISO8859 additional available for Epson

emulations‘

August 1995 Copyright IBM Corporation 1995.

Fujitsu DL3600 OSE

<CHR-SET> - SET1, SET2 *, ITALIC * GRAPHIC (unavail. for Epson emul.)‘

<AGM> (ii) - OFF *, ON

<PRF-SKIP> - NO-SKIP*, SKIP

<(page)WIDTH> - 13.6 inches *, 11.0 inches, 8.0 inches

<ZEROFNT> (iii) - NO-SLSH *, SLASH

<DC3-CDE> - ENABLE *, DISABLE

<CR-CODE> - (iii) ONLY *, CR&LF

<LF-CODE> - (iii)LF ONLY, LF&CR*

<RIGHTEND> - WRAP *, OVR-PRT (overprint characters at end-of-line)

(i) Not available for IBM XL24 emulation.

(ii) Alternate Graphics Mode available only for IBM XL24 emulation.

(iii) Not available for Epson emulations.

HARDWRE - Changes printer's hardware configuration.

<PPR-OUT> - CNTONLY *, DETECT, IGNORE

<PRT DIR> - BI-DIR *, UNI-DIR

<BUZZER> - ON *, OFF

<WORD LG> - 8BIT *, 7BIT

<(print )BUFFER> - 256BYTE, 2KBYTE, 8KBYTE, 24KBYTE

<FEEDER> - REAR * (no cut sheet feeder installed), SINGLE, DOUBLE

<FORMAT> - **8NONE1 *, 8NONE2, 8EVEN1, 8ODD1, 7EVEN1, 7ODD1,

7MARK1, 7SPACE1, 7EVEN2, 7ODD2

<BAUD RT> - 150, 300, 600, 1200, 4800, 9600 * ,19200

<PROTOCOL> - XON/XOFF *, DTR, REV-CHL (reverse channel), ETX/ACK

<DSR> - IGNORE *, DETECT

<DUPLEX> - FULL*, HALF

**Available only when a serial interface is installed.

LIST - Select to print a list of all current parameter settings.

DEFAULT - Select to reset MENU1 and MENU2 on control panel to factory

defaults.

SELF-TST - Select to run self-test. Prints the firmware version, resident emulations

and a continuous ASCII pattern. To pause self-test, press MODE or LF key. To

resume, press MODE or LF key again. To exit self-test and remain in setup mode,

press FF key. To exit self-test, save setup changes, and leave setup mode, press

ONLINE key.

V-ALMNT See "Critical Adjustments" below

TOF-ADJ - Set top-of-form with respect to top of physical page. Use ADJ to make

fine adjustments to top-of-form.

TOF-ADJ

Error Codes

When printer beeps four times and PAPER out light blinks, the printer hardware or a

font or emulation card is defective. If using a card, turn off printer, remove card and

clean gold contacts with a soft brush.

Common Problems and Fixes

Power does not turn on. Make sure power cord is securely connected to printer

and a working outlet.

Printer is on but does not print

1. Make sore printer is online and paper is loaded.

2. Make sure interface cable is securely connected at both ends.

3. If self-test does not execute normally, check interface, host, and printer and

software settings.

4. Make sure printer's emulation matches software.

Print quality is poor

1. Make sure paper thickness lever is set to match paper.

2. Make sure ribbon cartridge is properly installed.

3. Make sure ribbon feeds smoothly. Replace if worn.

Printing is erratic or wrong characters are printed

1. Make sure interface cable is securely connected at both ends.

2. Make sure emulation and, if applicable, serial settings on printer match host

settings.

Printing is vertically misaligned. Use V-ALMNT function (see "Printer Configura-

tion") to check and correct vertical character displacement.

Critical Adjustments

Vertical character displacement

1. Select V-ALMNT. Printer prints brief instructions and then starts printing rows

of parallel bars at letter quality speed.

2. If bars are offset to left (using first row as reference), repeatedly press MODE

key until bars are aligned. If offset to right, use LF key.

3. Press FF key to change speeds.

4. Repeat Steps 2 and 3 once to align bars at correspondence speed and again

to align bars at draft quality speed.

5. Press ONLINE key to terminate function, save new vertical alignment settings,

and exit setup mode.

Adjusting platen-to-print-head gap. The gap between platen and print head is

0.38 +/- 0.03 mm at both sides of platen.

1. Set paper thickness lever to position 1.

2. Set paper select lever to continuous forms.

3. Remove print head (see below).

4. Mount a gauge at print head position of carriage. Calibrate gauge using a

master gauge so that it reads zero (0.38 mm).

5. Move carriage to right and measure value indicated by gauge. Measure gap

while rotating platen by rotating idle gear and obtain average value.

6. Move carriage to left and rotate eccentric plate so that gauge indicates the

same value as that measured at right. Then fix plate in place.

7. Rotate the subassy. shaft so that the gauge indicates the value 0.38+1- 0.03

mm. (Plane surface is set vertically, close to main stay shaft.)

8. Replace gauge with print head and fix print head in place with mounting

screws.

Cover Removal

1. Pull off platen knob.

2. Open top cover and disconnect connector.

3. Push up top cover to remove.

4. Tip up cut sheet stand and pull up to remove.

5. Unplug two upper cover mounting screws at top front of printer and remove

upper cover.

Field Replaceable Units

Note:

Be sure to print a menu/configuration list before swapping printer.

DESCRIPTION OEM P/N

Print head D86B-1138-D783

Platen knob D860-1140-X514

Parallel interface board D05B-2903-D101

Serial interface board D05B-2903-D201

IBM P/N: 93F5997

IBM machine type: 1515-F19

Tech Support 800-877-7764

Item Options

<ORIGIN>** 1/6INCH, 1 INCH*, ADJ

<FINEAD> -7/60IN... +8/60IN

2FJ-4 IBM/TSS Internal Use Only

Produkt Specifikationer

Mærke:	Fujitsu
Kategori:	Printer
Model:	DL3600

Har du brug for hjælp?

Hvis du har brug for hjælp til Fujitsu DL3600 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Printer Fujitsu Manualer

Fujitsu DL3800 Manual

22 August 2024

Fujitsu DL3600 Manual

8 August 2024

Fujitsu DL3700 Manual

7 August 2024

Fujitsu DL9300 Manual

1 August 2023

Fujitsu DL3300 Manual

9 April 2023

Fujitsu DL1250 Manual

7 December 2022

Fujitsu DL1150 Manual

11 November 2022

Printer Manualer

Nyeste Printer Manualer

Utax P-3525 MFP Manual

30 Juli 2025

Ricoh IM C4510A Manual

30 Juli 2025

Utax 5009ci Manual

30 Juli 2025

Utax P-5030DN Manual

30 Juli 2025

Utax P-4030 MFP Manual

30 Juli 2025

Utax P-6035i MFP Manual

30 Juli 2025

Utax 3060i Manual

30 Juli 2025

Utax P-C2660DN Manual

30 Juli 2025

Utax P-4035i MFP Manual

29 Juli 2025

Utax P-3521D Manual

29 Juli 2025