Fujitsu WSHA100ML3 Manual

Fujitsu Aircondition WSHA100ML3

Læs gratis den danske manual til Fujitsu WSHA100ML3 (92 sider) i kategorien Aircondition. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Fujitsu WSHA100ML3, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/92
U0672837_2128_EN_6
29/03/2023
INSTALLATION
Air/water heat pump split 1 service
For professionals. To be kept by the user for future reference.
EN
Outdoor unit
WOHA060KLT
WOHA080KLT
WOHA100KLT
Hydraulic unit
WSHA050ML3
WSHA080ML3
WSHA100ML3
■ Installation and maintenance rules
The appliance must be installed and maintained
by an approved professional in accordance with
current regulations and codes of practice.
• Do not use any means to accelerate the
defrosting process or to clean the appliance,
other than those recommended by the
manufacturer.
• The appliance must be stored in a room that
does not contain continuously operating
ignition sources (for example: open fl ames,
gas appliance or operating electric heater).
• Do not pierce or burn.
• Be careful, refrigerants can be odorless.
■Handling
The outdoor unit must not be placed in a horizontal
position during transport.
If not kept upright during transport, the appliance
could be damaged through displacement of
the refrigerant and damage to the compressor
suspensions.
Any damage caused by transportation in a horizontal
position is not covered by the warranty.
If necessary, the outdoor unit may be tilted only
during manual handling (to go through a door or to
take a stair). This operation must be conducted very
carefully and the appliance must be immediately
restored to the upright position.
■Installation
The heat pump installation must meet the
requirements related to the location of the heat
pump.
The heat pump is designed to be installed at less
than 2000 m altitude.
In accordance with IEC 60-335-2-40 standard, the
hydraulic module of the heat pump as well as all
the refrigerant connections that cross the inhabited
area must be installed in rooms respecting the
minimum surface.
• Warning, hydraulic unit should not be installed
in an air current.
■Refrigerant
The maximum load of R32 fl uid with supplements
must not exceed 1.84 kg.
■Containment of refrigeration circuits
All refrigeration circuits are sensitive to dust and
moisture contamination. If any such pollutants
penetrate the refrigeration circuit, they can aff ect
the reliability of the heat pump.
• Make sure that the connections and
refrigeration circuits (hydraulic unit, outdoor
unit) are protected correctly.
• In the event of a subsequent failure and
following an inspection, the presence of
moisture or foreign bodies in the compressor
oil would automatically void the warranty.
- Check upon receipt that the fi ttings and refrigeration
circuit caps mounted on hydraulic unit and outdoor
unit are properly seated and secured (cannot be
loosened with bare hands). If this is not the case,
tighten them using a C spanner.
- Check also that the refrigeration connections are
sealed (plastic caps or tubes crimped at the ends
and brazed). If the caps must be removed during
the installation (tubes to be re-cut for example),
put them back as soon as possible.
■Hydraulic connections
The connection must comply with industry standard
practice according to current regulations.
Reminder : Seal everything when fi tting in
accordance with industry standard practice for
plumbing work:
- Use suitable seals (fi bre gasket, O-ring).
- Use Tefl on or hemp tape.
- Use sealing paste (synthetic depending on the
case).
Use glycol/water mix if the minimum fl ow
temperature is set below 10°C. If you are using a
glycol/water mix, arrange for an annual check on
the quality of the glycol. Use monopropylene glycol
only. The recommended concentration is 30%
minimum. Never use monoethylene glycol.
• In some installations, the presence of diff erent
metals can cause corrosion problems;
the formation of metal particles and sludge can
appear in the hydraulic circuit.
• In this case, it is advisable to use a corrosion
inhibitor in the proportions indicated by the
manufacturer.
• You must also ensure that treated water does
not become corrosive.
On the cold water inlet, place a safety valve
calibrated to between 7 and 10 bar max. (depending
on local regulations) and connected to a drain
pipe leading to the sewer. Operate the safety
valve according to manufacturer's specifi cations.
The domestic hot water tank must be fed with cold
water passing through a safety valve. There must
be no other valves between the safety valve and
the tank.

Produkt Specifikationer

Mærke: Fujitsu
Kategori: Aircondition
Model: WSHA100ML3

Har du brug for hjælp?

Hvis du har brug for hjælp til Fujitsu WSHA100ML3 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Aircondition Fujitsu Manualer

Fujitsu

Fujitsu ASHA009HCAH Manual

3 April 2025
Fujitsu

Fujitsu AUTH18KVLA Manual

30 Marts 2025
Fujitsu

Fujitsu ACY40K-KA Manual

24 Februar 2025
Fujitsu

Fujitsu ACY100 KA Manual

24 Februar 2025
Fujitsu

Fujitsu ACY35K-KA Manual

24 Februar 2025
Fujitsu

Fujitsu ACY25-KA Manual

24 Februar 2025
Fujitsu

Fujitsu ABY71-KA ECO Manual

24 Februar 2025
Fujitsu

Fujitsu AIRSTAGE AJY040LBLDH Manual

11 Januar 2025
Fujitsu

Fujitsu ARXP014HLAH Manual

8 Januar 2025
Fujitsu

Fujitsu ARXD009HLAH Manual

8 Januar 2025

Aircondition Manualer

Nyeste Aircondition Manualer

IFB

IFB FastCool CI1833A223G5 Manual

7 September 2025
Gree

Gree ERAF 0721A Manual

1 September 2025
Bosch

Bosch Cool 2000 Manual

1 September 2025
Bosch

Bosch Cool 4000 Manual

31 August 2025
Equator

Equator PAC 162R Manual

27 August 2025
Equator

Equator PAC 8000 Manual

26 August 2025
DAB

DAB ESYLINK Manual

23 August 2025
Daikin

Daikin Cloud Plus Manual

18 August 2025
Daikin

Daikin BRC1E53C7 Manual

11 August 2025
Daikin

Daikin FXSN71A2VEB Manual

11 August 2025