Futaba R7108SB Manual

Futaba Modtager R7108SB

Læs gratis den danske manual til Futaba R7108SB (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Futaba R7108SB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

R7108SB

1M23N17499

FASSTest-2.4GHz Bidirectional Communication System / FASST(Multi-ch,7ch) -2.4GHz

S.BUS2 / S.BUS Port and 8 Channels for Conventional System Receiver

Thank you for purchasing a Futaba R7108SB FASSTest-2.4GHz compatible receiver.

The R7108SB receiver features bi-directional communication with a FASSTest

Futaba transmitter using the S.BUS2 port. Using the port an impressive array of telemetry sensors may be utilized. It also includes both standard PWM output S.BUS2

ports (1-8ch) and S.BUS output ports. The can also be switched to the R7108SB FASST(Multi-ch/7-ch) System.

Antenna

installation

*When on "FASST-7ch" mode, the fail safe func-

tion can be set for 3-channel only.

*Be sure that when using ESCs regulated output

the capacity of the ESC must meet your usage

condition.

*Never use dry batteries for the power supply of

WKH56%DVWKH\PD\FDXVHGLI¿FXOWLHV

• Analog servos cannot be used with the R7108SB in the FASSTest

12CH / FASST High-speed mode.

• Don't connect to Extra Voltage before turning on a receiver.

and promote safe modeling Futaba has adopted a diversity antenna system.

This allows the receiver to obtain RF signals on both antennas and fly

problem-free.

FASSTest-2.4 GHz system(18 ch/12 ch mode)

FASST-2.4 GHz system (Multi-ch/7 ch mode)

S.BUS2 and S.BUS port and 8 channels for con-

ventional system receiver

• Dual antenna diversity

• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3

mm)

• Weight: 0.42 oz. (12.0 g)

• Power req uireme nt: 3.7 V to 7.4 V(Voltage

range: 3.5 V to 8.4 V)

• Battery F/S Voltage: FASSTest---It sets up with a

transmitter FASST---3.8 V

• Extra Voltage port: 0

70 V DC

6HUYRIRUFRQYHQWLRQDO

V\VWHP

/('

$QWHQQD

/LQN0RGHVZLWFK

([WUD9ROWDJH3RUW

,WLVQRWXVHGIRUDOLQN

,WFRQQHFWVZLWKWKHEDWWHU\

IRUSRZHUHWF

Ex te rn al v o lt age in put

cable of an option

LVXVHG

7KHYROWDJHRIWKHEDWWHU\

FDQEHGLVSOD\HGZLWKD

WUDQVPLWWHU

7HPSHUDWXUH

6HQVRU

6%866HUYR

6%86*\UR

+8%

&KDQQHORXWSXW

&KDQQHORXWSXW

6%86SRUW

6%ك

6%86SRUW

6%86ك

9ROWDJH

6HQVRU

9ROWDJH

6HQVRU

530

6HQVRU

$OWLWXGH

6HQVRU

$LUVSHHG

6HQVRU

6%867RRO

(Typical installation)

5HFHLYHU

Do not insert either a switch

or battery in this manner.

Hereby, Futaba Corporation declares that the radio equipment type is R7108SB in compliance with Directive 2014/53/

EU. The full text of the EU declaration of conformity is available at the following internet address:

http://www.rc.futaba.co.jp/english/dl/declarations.html

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure

limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum dis

tance 20cm between the radiator & your body.

French: Cet appareil radio est conforme au CNR-210 d’Industrie Canada. L’utilisation de ce dispositifest autorisée

seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit

être prêt à accepter tout brouillage radioélectrique reçu, même sice brouillage est susceptible de compromettre le fonc

tionnement du dispositif. Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un

environnement non contrôlé.

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non

contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de ray

onnement et votre corps.

This device, trade name Futaba Corporation, model number R7108SB, complies with part15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

CAUTION: To assure continued FCC compliance

$Q\FKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHJUDQWHHRIWKLVGHYLFHFRXOGYRLGWKHXVHUVDXWKRULW\

to operate the equipment.

2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

The responsible party of this device compliance is:

FUTABA Corporation of America

2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.

Phone:1-256-461-9399 FAX:1-256-461-1059 E-mail: service@futabaUSA.com

$QWHQQDSDUW

6OHHYH

&RD[LDOFDEOH

Output

connector

Channel

Mode A

8CH

Mode B

7CH

Mode C

16CH

Mode D

15CH

11199

2 2 2 10 10

3 3 3 11 11

4 4 4 12 12

5 5 5 13 13

6 6 6 14 14

7/B 7 7 15 15

8/SB 8 S.BUS 16 S.BUS

Red LED

blink

1 time 2 times 3 times 4 times

*FASST mode cannot use telemetry functions.

The R7108SB is capable of changing its channel allocations as

described in the table below. This is especially important when using

the receiver in a dual receiver mode. See your transmitter operation

manual for complete details on operating in the dual receiver mode.

Turn on the receiver. [Transmitter is always OFF]

Press and hold the Link/Mode button for 5 seconds to 10

seconds.

When the LED of the receiver changes from blinking red to

blinking red with green, Link/Mode button is released.

The LED should now blink red two times in the patterns

described in the chart below.

Each press of the Link/Mode button advances the receiver to

the next mode.

When you reach the mode that you wish to operate in, press

and hold the Link/Mode button for more than 2 seconds.

When LED blinks in green with red, it is the completion of a

mode change, Link/Mode button is released.

Please cycle the receiver power off and back on again after

changing the Channel mode.

Turn on the receiver. [Transmitter is always OFF]

Press and hold the Link/Mode button for 10 seconds to 15

seconds.

When the LED begins to blink green the button may be

released.

The LED should now be blinking green in one of the patterns

described by the chart below.

( Default : FASSTest )

Each press of the Link/Mode button advances the receiver to

the next system.

When you reach the system that you wish to operate in, press

and hold the Link/Mode button for more than 2 seconds.

When the LED blinks green and red, the system change is

complete. Release the Link/Mode button.

Please cycle the receiver power off and back on again after

changing the system.

FASSTest is a bidirectional communication system between the

R7108SB receiver and FASSTest capable transmitters. Multiple

optional telemetry sensors may be connected to the S.BUS2 on the

receiver and that data is in turn displayed on the transmitter.

Link to the transmitter : FASSTest

Bring the transmitter and the receiver close to each other,

within 20 inches (half meter).

Turn on the transmitter. Place the transmitter into the receiver

linking mode.

Turn on the receiver.

The receiver will wait for the linking process to begin for 2

seconds. Following that it will return to the normal operation

mode.

When the LED of the receiver changes from blinking red to

solid green, linking is complete.

(A link waiting state is ended in 1 second.)

• Refer to the transmitter's operation manual for complete details on how

to place the transmitter into the linking mode.

• If there are many FASSTest systems turned on in close proximity, your

receiver might have difficulty establishing a link to your transmitter.

This is a rare occurrence. However, should another FASSTest

transmitter/receiver be linking at the same time, your receiver could link

to the wrong transmitter. This is very dangerous if not noticed. To avoid

the problem, we strongly recommend that you double check whether

your receiver is really under control by your transmitter.

• If the System Type of the transmitter is changed, the receiver will need

to be re-linked to the transmitter.

Link to the TMA-1 Telemetry Adapter

R7108SB has to be FASSTest.

First, a transmitter and a receiver are linked.

Transmitter is turned off.

Press and hold the Link/Mode button of R7108SB for 15 seconds.

After the R7108SB LED lights in this sequence, Red Blink -- with Red Green

Blink -- Green Blink -- Red Blink, release the Link/Mode button.

When in link mode with the R7108SB, the TMA-1 LED blinks green along with

the red LED of the receiver.

Push the TMA-1 link button as long as necessary for its LED to blink.

Completion of a link will change LED of TMA-1 green from red only for a

moment.

Please cycle the receiver power.

S.BUS2 extends S.BUS and supports bidirectional communication.

Sensors are connected to the S.BUS2 port.

Link to the transmitter : FASST

Bring the transmitter and the receiver close to each other,

within 20 inches (half meter).

Turn on the transmitter and receiver.

Link operation is performed by the Link/Mode switch.

• When using TM-8 module, it's possible to set F/S position (only 3CH).

0 to 1 sec. 1 to 2 sec. More than 2 sec.

0 sec. 1 sec. 2 sec.

Press and Hold time

No function

With TM-8

(not included in this set)

To set the F/S

position(No re-link)

Re-link(ID set) and to

set the F/S position

No function

Besides TM-8

Re-link(ID set)

Refer to the instruction manual of the transmitter or module used for a description

of the linking operation, F/S position setting methods and other details.

R7108SB also can use the FASST-Multi/7ch FASST mode. The mode does

not support the telemetry functions. The FASST system has a normal mode and

a high-speed mode. However, in the High-speed mode, analog servos cannot be

used.

FUTABA CORPORATION

Hobby Radio Control Business Center Sales & Marketing Department

1080 Yabutsuka, Chosei-mura, Chisei-gun, Chiba-ken, 299-4395, Japan TEL: +81-475-32-6051, FAX: +81-475-32-2915 ©FUTABA CORPORATION 2020, 6 (1)

Produkt Specifikationer

Mærke:	Futaba
Kategori:	Modtager
Model:	R7108SB
Bredde:	24.9 mm
Dybde:	47.3 mm
Højde:	14.3 mm
Vægt:	12 g
Antal pr. pakke:	1 stk
Produkttype:	Modtager til fjernbetjening
Certificering:	CE
Ikke for børn fra 0-3 år:	Ja
Driftsspænding (maks.):	8.4 V
Driftsspænding (min.):	3.5 V