GARDE 181CHEESE38 Manual

GARDE Skæremaskine 181CHEESE38

Læs gratis den danske manual til GARDE 181CHEESE38 (1 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 19 anmeldelser. Har du et spørgsmål om GARDE 181CHEESE38, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

QUICK START

GUIDE

CHEESE CUTTERS

MODELS

181CHEESE38 - 3/8"

181CHEESE34 - 3/4"

Please read and comply with the instructions listed on this document.

To get the best service life and performance from your machine, clean

it thoroughly before and after each use by following the instructions

listed below. Minimize the use of alkaline cleaners, as they may dull the

ﬁnish and cause pitting.

OPERATION

1. Set the unit on a at, sturdy surface.

2. Prepare the block of cheese to be cut. Ensure that the

block of cheese is reduced to a size that can be placed

on the support block assembly.

3. Raise the cutting bow to the upright position and place

the cheese block on the support block assembly. It is

recommended that the largest dimension of the cheese

block be pointed towards the cutting bow wires to

produce the best cut.

4. Slowly and steadily press the cutting bow through the

cheese block. This will produce slices of cheese.

5. To produce cheese cubes, rotate the cheese block

90 degrees and repeat steps 3 and 4.

CLEANING AND MAINTENANCE

1. For best results, wash the unit soon after each use to

prevent cheese from hardening prior to washing.

2. Pull ring pin to remove the cutting bow.

3. Wash the main frame thoroughly with a pressure spray or

conventional sink.

4. Use a cleaning brush to wash the cutting bow and the

cutting bow wires.

- Cutting bow wires can be removed and washed separately

by removing the screws on the back of the cutting bow.

5. Dry all components and reassemble the unit.

REPLACING THE CUTTING BOW

1. Remove the cutting bow from the unit by removing the ring

pin and lifting the cutting bow off.

2. Line up the alternate cutting bow on the frame so the ring

pin holes are aligned.

3. Insert the ring pin from either side of the frame.

REPLACEMENT PARTS

Item Number Description

181CHSBLD34

3/4" Cutting Bow

181CHSBLD38

3/8" Cutting Bow

181CHSBLDSET

3/4" 3/8" and Cutting Bow Set

181SUCCUP Suction Foot

181RINGPIN Ring Pin

02/2024

Produkt Specifikationer

Mærke:	GARDE
Kategori:	Skæremaskine
Model:	181CHEESE38

Har du brug for hjælp?

Hvis du har brug for hjælp til GARDE 181CHEESE38 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skæremaskine GARDE Manualer

GARDE 181DM12SC Manual

15 November 2025

GARDE 181DM14SC Manual

13 November 2025

GARDE 181DM14 Manual

12 November 2025

GARDE 181DM14WM Manual

12 November 2025

GARDE 181DM12 Manual

12 November 2025

GARDE 181DM12WM Manual

11 November 2025

GARDE 181PBLD38 Manual

27 August 2025

GARDE 181FC38SC Manual

27 August 2025

GARDE 181FC12CTM Manual

26 August 2025

GARDE 181CORE8 Manual

26 August 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Vollrath Redco Instacut Manual

15 December 2025

Maestro MR-590 Manual

8 December 2025

Maestro MR-591 Manual

8 December 2025

Omcan 11399 Manual

5 December 2025

Vevor SK-720L Manual

2 December 2025

Vevor PGYHJ3626 Manual

2 December 2025

Lakeland 62167 Manual

2 December 2025

Vevor PGYHJ2814 Manual

1 December 2025

Vevor PGYHJ2615 Manual

30 November 2025

Sommertal AS170 Manual

30 November 2025