GARDE 181FCWDG6WM Manual

GARDE Skæremaskine 181FCWDG6WM

Læs gratis den danske manual til GARDE 181FCWDG6WM (2 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om GARDE 181FCWDG6WM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

QUICK START GUIDE

WALL-MOUNT FRY CUTTERS

MODELS

181FC14WM - 1/4" Fry

181FC38WM - 3/8" Fry

181FC12WM - 1/2" Fry

181FCWDG6WM - 6 Wedge

181FCWDG8WM - 8 Wedge

SAFETY INSTRUCTIONS

CAUTION

Be careful when handling and operating the machine, as

the blades are very sharp. Always keep your hands away

from the blades.

WALL MOUNT INSTRUCTIONS

NOTE: It’s important that the unit be mounted to

a stud to prevent it from falling during use!

1. Position the bracket on the wall where you would

like to mount the unit.

2. Make sure the orientation of the bracket is correct

so that the fry cutter slides in from the top.

3. Find the closest stud and move the bracket so that

the mounting holes on one side of the bracket are

over the stud.

4. Mark the 6 hole locations and remove the machine.

5. Drill 5/32" holes through these marks.

6. Re-position the bracket on the wall aligned with the

holes and secure using washers and mounting screws.

7. Slide the fry cutter into the bracket.

COUNTER MOUNT INSTRUCTIONS

1. Choose a spot on a sturdy countertop where you'd like

to mount the unit. Ensure the mounting screws will not

penetrate anything under the counter.

2. Mark the 4 hole locations and remove the machine.

3. Drill 5/32" holes through these marks.

4. Re-position the unit to align with the holes and secure

using washers and mounting screws.

OPERATION

1. Put a potato on the blade and holder assembly.

2. After making sure your hands and ngers are clear of

the cutting area, pull the handle in one quick motion.

a. This may occasionally need to be repeated for

potatoes that are exceptionally large.

b. DO NOT try to cut potatoes that are bigger than

the opening in the blade holder.

3. When nished, be sure to clean the machine using the

instructions below.

NOTE: To cut 1/4" and 1/2", use the 1/4" push block.

To cut 3/8", use the 3/8" push block.

CLEANING

NOTE: Avoid using alkaline cleaners as they may dull the

nish and cause pitting.

1. Release the push block by removing the thumb screws.

2. Release the blade & holder assembly by removing the

wing nuts.

3. Carefully remove the blade & holder assembly, as well

as the push block.

4. Wash the push block and blade and holder assembly.

5. The blade & holder assembly can be further

disassembled for more thorough cleaning by:

a. Removing the thumb screws and blade holder plate.

b. Lightly tapping the blades and spacers to remove

them from the holder.

6. To reassemble the blade and holder assembly:

a. Put the blade holder on a at surface with the

spacer pockets facing up.

b. Insert blade spacers with their slots facing the

inner opening of the blade holder.

c. Insert blades with cutting edge facing down

and slots facing up.

d. Insert blades with cutting edge and slots facing

down.

e. Put the blade holder plate into place and secure

it with the thumbscrews.

7. Simply reverse the disassembly instructions to

reassemble the fry cutter.

8. When needed, lubricate the guide rods with mineral oil,

food grade grease or parafn.

NOTE: DO NOT use cooking oil.

08/2023

QUICK START GUIDE

WALL-MOUNT FRY CUTTERS

REPLACEMENT PARTS

BLADE ASSEMBLIES

#181PBA14 #181PBA38 #181FCWDG6BLD #181FCWDG8BLD#181PBA12

1/4" 3/8" 1/2" 6-Section Wedge 8-Section Wedge

BLADES

#181PBLD14 #181PBLD38 #181PBLD12

1/4" (22 Blades) 3/8" (16 Blades) 1/2" (10 Blades)

PUSHER BLOCKS

#181PPB38 #181PPB1412 #181FCWDG6PB #181FCWDG8PB

3/8" 1/4" 1/2" 6-Section Wedge 8-Section Wedge

ADDITIONAL PARTS

#181BRKTFF #181BUMPER #181SSWNUT #181TSCREW #181FT1

Wall Bracket Bumper Wingnut Thumb Screw Feet (4)

08/2023

Produkt Specifikationer

Mærke:	GARDE
Kategori:	Skæremaskine
Model:	181FCWDG6WM

Har du brug for hjælp?

Hvis du har brug for hjælp til GARDE 181FCWDG6WM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skæremaskine GARDE Manualer

GARDE 181DC38 Manual

15 Juni 2025

GARDE 181FCWDG6 Manual

15 Juni 2025

GARDE 181DC14 Manual

15 Juni 2025

GARDE 181CHEESE38 Manual

15 Juni 2025

GARDE 181PBA12 Manual

15 Juni 2025

GARDE 181PPB1412 Manual

15 Juni 2025

GARDE 181DC12 Manual

15 Juni 2025

GARDE 181DM38 Manual

15 Juni 2025

GARDE 181TSLC316 Manual

14 Juni 2025

GARDE 181BPKIT1 Manual

14 Juni 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Bizerba CSP Manual

15 Juni 2025

Choice 4071875TS Manual

15 Juni 2025

Choice 407ONSLIC14 Manual

15 Juni 2025

Nemco 56610-2 Manual

15 Juni 2025

Vollrath 47715 Manual

15 Juni 2025

Prince Castle 943-DH Manual

15 Juni 2025

Vollrath Cube King 1812 Manual

14 Juni 2025

Choice 40725D Manual

14 Juni 2025

Vollrath 401N Manual

14 Juni 2025

Choice 407375D Manual

14 Juni 2025