GARDE 181TSLC38 Manual

GARDE Skæremaskine 181TSLC38

Læs gratis den danske manual til GARDE 181TSLC38 (1 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om GARDE 181TSLC38, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

QUICK START GUIDE

TOMATO SLICERS

MODELS

181TSLC316 - 3/16" Slices

181TSLC732 - 7/32" Slices

181TSLC14 - 1/4" Slices

181TSLC38 - 3/8" Slices

SAFETY INSTRUCTIONS

CAUTION

Be careful when handling and operating the machine, as

the blades are very sharp. Always keep your hands away

from the blades.

PREPARATION

1. This unit comes fully assembled.

2. Place the unit on a sturdy work surface.

3. The guides for the pusher assembly located along the

sides of the cutting board need to be lubed regularly to

keep your slicer operating smoothly. Using a food grade

sanitary lube (such as 401PETROLGEL) will ensure you

get a clean slice every time.

OPERATION

1. Pull the handle toward you and place a tomato on the

slide board between the pusher plates and the blades.

2. Remove hands and ngers from the cutting area

and push the handle toward the blades with one

quick motion.

3. Remove the sliced tomato from the slide board

and repeat as necessary.

BLADE TENSION INSTRUCTIONS

1. Ensure that the blade holder assembly is rmly

mounted on the frame with the sharp side of the

blades toward the pusher assembly.

2. Be sure the hex head screws on the right side of the

blade holder are tight.

3. Tighten the hex head screws on the left end of the

blade holder until the blades “hum” when strummed

or plucked.

4. Check the blade tension each time the machine is used.

CLEANING

NOTE: Avoid using alkaline cleaners as they may dull the

nish and cause pitting.

1. Remove the thumb screws and the slide stop from the

pusher assembly. Pull the pusher off the end of the

slide board.

2. Remove the mounting screws from the slide board and

blade shield.

3. To totally disassemble the pusher assembly, remove

the acorn and hex nuts on the top of the stack and

carefully remove the pusher plates and spacers.

Remove the additional screws if you wish to

disassemble the guide plate.

4. To reassemble, reverse the procedure.

NOTE:

Always rinse the tomato slicer in cold or lukewarm

water after it has been washed in hot water.

Hot water makes the slide board expand which may

make it difcult to use the pusher assembly until

the slide board returns to room temperature.

NOTE: After reassembly, you must add tension back to

the blades.

REPLACEMENT PARTS

BLADE ASSEMBLIES

#181BLDTS316 #181BLDTS732 #181BLDTS14 #181BLDTS38

3/16" 7/32" 1/4" 3/8"

#181PTS316 3/16"

#181PTS732 7/32"

#181PTS14 1/4"

#181PTS38 3/8"

ADDITIONAL PARTS

#181TSCREW Thumb Screw

#181FT1 Feet (4)

08/2023

Produkt Specifikationer

Mærke:	GARDE
Kategori:	Skæremaskine
Model:	181TSLC38

Har du brug for hjælp?

Hvis du har brug for hjælp til GARDE 181TSLC38 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skæremaskine GARDE Manualer

GARDE 181CHEESBLK Manual

14 Juni 2025

GARDE 181FC38WM Manual

14 Juni 2025

GARDE 181FC14 Manual

14 Juni 2025

GARDE 181FC38 Manual

14 Juni 2025

GARDE 181FC14WM Manual

14 Juni 2025

GARDE 181FCWDG6WM Manual

14 Juni 2025

GARDE 181FC12SC Manual

14 Juni 2025

GARDE 181TSLC38 Manual

13 Juni 2025

GARDE 181WEDGE6 Manual

13 Juni 2025

GARDE 181WEDGE10 Manual

13 Juni 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Gourmia GES580 Manual

14 Juni 2025

Vollrath 500N Manual

14 Juni 2025

Nemco 55418 Manual

14 Juni 2025

Nemco 57500-4 Manual

14 Juni 2025

Vollrath 47714 Manual

14 Juni 2025

Choice 407ONSLIC316 Manual

14 Juni 2025

Vollrath 403NH Manual

14 Juni 2025

Vollrath 700-1 Manual

14 Juni 2025

Nemco 57500-6 Manual

14 Juni 2025

Globe SG13 Manual

14 Juni 2025