GE 15136 Manual

GE Tidsskifte 15136

Læs gratis den danske manual til GE 15136 (3 sider) i kategorien Tidsskifte. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 25 anmeldelser. Har du et spørgsmål om GE 15136, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

APPLICATION

This digital GE Time Switch (15132) is a universal, electromechanical time

switch which can be ﬁeld conﬁgured for various power supply voltages.

The voltage options include 120VAC, 208/240VAC and 277VAC – all within

the same unit! Selection of the desired supply voltage is easily achieved

by positioning dipswitches on the printed circuit board assembly (consult

Dipswitches Conﬁguration on back). The mechanism is mounted in a NEMA

indoor or outdoor enclosure and is intended for the control of lighting, heating,

air conditioning, pumps, motors, or general electrical circuits in residential,

commercial, industrial and agricultural facilities.

SPECIFICATIONS

Input Voltage: 120 VAC, 208/240 VAC, or 277 VAC in all units based

upon dipswitch conﬁguration.

15087 NEMA 3R Indoor & Outdoor BM-A301US5-O2

15207 NEMA 1 Indoor BM-A301US5-I2

56922 NEMA 1 Indoor BM-A301US5-I2

15132 NEMA 3R Indoor & Outdoor EM-A301US9-O2

Switch Rating: DPDT Models

Normally Open Contacts

40A Resistive, 120-277Vac.

30A General Purpose, 120-277Vac.

20A Resistive, 30Vdc

1 HP, 120Vac ; 2HP, 240Vac ;

20A Ballast, 120-277Vac.

15A Tungsten, 120Vac

5.4A Tungsten, 208-277Vac.

800VA, Pilot Duty, 120Vac.

720VA, Pilot Duty, 240-277Vac.

TV-5, 120Vac

Normally Closed Contacts

30A Resistive, 120-277Vac

15A General Purpose, 120-277Vac

15A Resistive, 30Vdc

20A Ballast, 120-277Vac

1/4HP, 120Vac; 1/2HP, 208-240Vac.

290VA, Pilot, 120Vac.

360VA, Pilot, 208-240Vac.

NOTE: If loads are connected to both NC and NO contacts, both contacts are

decorated to 67% of the above values.

ENVIRONMENTAL RATINGS

Ambient Temperature: –40F to 130F

Humidity: 0-95% RH, Non-condensing

WIRING CONNECTIONS

Screw clamp terminals for up to 2 AWG #8 wires per position. For supply

connections, use 8AWG or larger wires suitable for at least 105° C. Use copper

conductors only.

Lights

Power LED (Orange) – Light illuminates when power is applied to

the timer

Status LED (Green) – Light illuminates when power is applied to load.

Included Hardware

INSTALLATION

CAUTION: Before wiring or servicing, power to this time switch and the

equipment it controls must be turned off. Turning off the time switch only

will not prevent a shock hazard. Replace cover plate within housing before

supplying power to time switch. If you are not comfortable installing this

device please contact a licensed electrician. Before installing this product read

all instructions carefully.

Removing Knockout

1. Select knockouts to be used. Remove the inner 1/2” knockout by inserting

a ﬂathead screwdriver on the inner most ring and carefully punching the

knockout loose. Remove slug. If the 3/4” knockout is required, remove the

outer ring with pliers after removing the 1/2” knockout. Smooth edges with

a knife if necessary.

Please refer to Quick Start Guide for Examples and More Details.

Mounting of the Time Switch Box

NOTE - Before mounting be sure to remove knockouts for the wires, (see Quick

Start Guide)

1. In order to mount the box you will need the 3 supplied anchors and 3

supplied screws from the hardware list above. (Anchors included are

designed for mounting on sheetrock.)

2. Using the box as a template, mark with a pencil where the three pilot holes

will be drilled.

3. Using the appropriate drill bit size, drill the pilot holes (Note that if drilling

into wood or metal a specialized drill bit may be needed.)

See Drill Diagram.

4. For sheetrock; use a hammer to gently tap the anchors into the pilot holes.

5. Place the box up to the pilot holes or anchors and insert the screws

accordingly.

Wiring the Device to the Timer

NOTE - For outdoor installation use rain tight or wet location conduit hubs that

comply with requirements of UL 514B (standard for ﬁttings for conduit and

outlet boxes).

1. Remove 2 screws retaining the interior cover panel and remove the panel.

2. Refer to Figure 1 and wiring diagrams to determine appropriate placement

of wires. It is the responsibility of the installer to ensure that all applicable

National and Local code requirements are met. If you are unsure of these

requirements, contact a licensed electrician immediately.

3. GROUNDING: This enclosure is of plastic construction and does not require

a ground connection. This enclosure does not provide grounding between

Digital Time Switch

Soft Wood 5/64”

Material Drill Bit Size

Drill Diagram

Hard Wood 3/32”

Metal 5/64”

Sheetrock 3/16”

Anchors Needed?

Yes

QTY Hardware

3 M4 Anchors 1” Long

3 M4 Screws 1” Long

2 8 AWG Jumpers for 240V AC

2 10 AWG Jumpers for 120V AC

1 Wire Nut (For Ground Wires)

15136 NEMA 3R Indoor & Outdoor

GE 15136 Timer

http://waterheatertimer.org/GE-timers-and-manuals.html#15136

Initial Set Up:

1. Push the “R” button before programming to clear out any settings. Once

the “R” button is pressed the screen will begin to ﬂash. A paperclip may be

needed for this step.

(If the “R” button appears to stick down, use a paperclip to maneuver

it until it pops back up. The screen will ﬂash if the button is popped up

successfully.)

2. Press the “Clock” button and the screen will stop ﬂashing and be ready for

programming.

Setting the Current Time:

1. Press and Hold the “Clock” button during the entire setting.

2. Press the “H+” button to set the hours.

3. Press the “M+” button to set the minutes.

4. Press the “Day” button to set the day of the week.

5. Release the “Clock” button.

Programming ON/OFF Settings:

1. Press the “Timer” button once and the TIMER 1 ON - - : - - appears.

2. Press the “H+” and “M+” button to set the hours and minutes to the

desired time.

3. Press the “Day” button to select the day(s) the setting will be active. Refer

to the Multiple Weekday Group below to see the available settings.

4. Press the “Timer” button to store the setting and proceed to the next

setting TIMER 1 OFF - - : - -.

5. Repeat for all remaining setting options (9 Total ON/OFF settings). Once

completed press the “Clock” button to return to the main display.

Multiple Weekday Groups:

Apart from individual week days, pressing the “Day” button also selects

multiple day combinations such as:

‧ Monday thru Friday ‧ Tuesday & Thursday & Saturday

‧ Saturday & Sunday ‧ Monday thru Wednesday

‧ Monday thru Saturday ‧ Thursday thru Saturday

‧ Monday & Wednesday & Friday ‧ Monday thru Sunday

After setting a single day or a multi-day-combination the programmed timer

settings will be carried out on each of the week-days at the same time.

conduits. When using non-metallic conduit or cable, connect

the ground wires of all cables together with the provided

wire nut. When metallic conduit is used; as the grounding

connection, use grounding type bushing and a jumper wire

between each conduit.

Dipswitch Conﬁguration

WARNING: Failure to properly conﬁgure the dipswitch will result

in damage to the unit and void any warranty! Before installing

and wiring the GE Time Switch, proper conﬁguration must

be selected. Unit is shipped with DIP Switches set for 277VAC

Input Voltage. Also, do not check circuits by “sparking” wires to

terminals. Damage to timer may result.

4. Determine the input voltage which will be applied to the timer.

(120V AC, 208-240V AC, or 277V AC)

5. Set the DIP Switch according to the diagram below.

6. Reinstall interior cover panel. Opposite of step 1.

TIMERN CN O

COM

NC2

NO2

COM2

LOAD

TIMERN CN O

COM

TO 200/240/277V LINE

TO 120V LINE

NC2

NO2

COM2

LOAD

TIMERN CN O

COM

TO 24V LINE

NC2

NO2

COM2

LOAD

TO 120V LINE

TO LOAD

120V Timer, 120V Load and 24V Load

Wired as Single Throw

200/240/277V Timer, 200/240/277V Load, Double Break

Wired as Single Throw

120V Timer, 200/240/277V Load Double Break

Wired as Single Throw

Typical Wiring Diagrams—DPDT

TO POWER SUPPLY

TO POWER SUPPLY 1 TO POWER SUPPLY 2

Timer and Load, Same Voltage

Wired as Single Throw

TO LOAD

TO 120V LINE

HIGH

LOW

COM

LOAD

NCTIMERN OC OM

TIMERN CN OC OM

120V Two Speed Fan

Wired as Double Throw

Timer and Load, Different Voltage

Wired as Single Throw

Typical Wiring Diagrams—SPDT

Field Wiring

Timer Internab Wiring

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

105

MINIMUM COPPER

WIRE SIZE (AWG)

MAX. LOAD (AMP) MIN. INSULATION

TEMP(°C)

Figure 1

Override

(Manual ON/OFF Switched)

Timer

(9 Programs Setting)

Clock

(Current Time Setting)

LCD

(Function Figures)

(Reset)

H-

(Hours Setting)

M-

(Minutes Setting)

Day

(Days Setting)

Operating Instructions

Basic Settings

120VAC

OFF

277VAC (Default)

OFF

208~240VAC

Produkt Specifikationer

Mærke:	GE
Kategori:	Tidsskifte
Model:	15136

Har du brug for hjælp?

Hvis du har brug for hjælp til GE 15136 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Tidsskifte GE Manualer

GE 56922 Manual

24 August 2024

GE 15136 Manual

23 August 2024

GE 15250 Manual

23 August 2024

Tidsskifte Manualer

Nyeste Tidsskifte Manualer

SilverCrest Digitale tijdschakelaar Manual

15 Januar 2025

Intermatic ST01 Series Manual

15 Januar 2025

Selecttime 1728391 Manual

14 Januar 2025

Profile PCF-360 Manual

23 September 2024

Profile 840000020 Manual

17 September 2024

Sygonix 1625525 Manual

27 August 2024

Sygonix 1528595 Manual

27 August 2024

TimeControl AX-801 Manual

26 August 2024

TimeControl DX-2 Manual

26 August 2024

TimeControl 2000 Electronic Manual

26 August 2024