GE DSR24RWWH Manual

GE Tørretumbler DSR24RWWH

Læs gratis den danske manual til GE DSR24RWWH (12 sider) i kategorien Tørretumbler. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5 anmeldelser. Har du et spørgsmål om GE DSR24RWWH, eller vil du spørge andre brugere om produktet?

Side 1/12
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IMPORTANT Save these
instructions for local electrical
inspector’s use.
IMPORTANT Observe all
governing codes and ordinances.
Note to Installer Be sure to leave these
instructions with the Consumer.
Note to Consumer Keep these instructions
for future reference.
Installation and service must be performed
by a qualified installer.
Proper installation is the responsibility of
the installer.
Installation Stack Stand Kit
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or visit our Web site at: www.GEAppliances.com
FOR YOUR SAFETY:
WARNING
Electric Shock Hazard. Disconnect power
before servicing. Failure to do so could
result in serious injury or death.
Potential Personal Injury. More than one
person is recommended to lift the dryer
into position because of its weight and
size. Failure to do so could result in
personal injury or death.
Avoid Tipping and Rupture of Utility
Services. Stand must be securely
assembled and dryer fastened to stand,
per installation instructions. Stand must be
securely fastened to wall, per installaiton
instructions. Failure to do so could result in
personal injury/death or property damage.
FOR USE WITH RECOMMENDED
COMPACT-TYPE ELECTRIC DRYERS
TOOLS YOU WILL NEED
Flat-head screwdriver
Adjustable wrench
Nut driver
PARTS INCLUDED
PART QUANTITY
Lid Latch 1
Type A Screw 2
1/4–20 x 3/4
Type B Screw 6
1/4–20 x 112
Type C Screw 2
1/4–10 x 134
Type D Screw 7
10–16 x 5/8
Lock Nut 8
1/4–20
Spacer Ring 1
175D1807P423
49-90159
03-03 JR
Installation Instructions
2
PARTS INCLUDED (cont.)
The stand base has an angle bracket at each
end. One end of the angle bracket is 2212
long and has mounting holes in it. This end
goes up. The other end of the angle bracket
is 28 long and has no holes. This longer end
(without holes) goes down.
DETERMINE STAND WIDTH
Your new stand can be assembled to two
different widths:
22for smaller, compact washers
24for larger washers
Check your washer width to determine the
stand width you need. The compact dryer
will assemble to either width.
1
ATTACH WALL MOUNTING
BRACKET
Attach one end of the wall mounting
bracket to one of the upper rear holes on
one of the stand bases using a Type A
screw and a lock nut. Make sure screws are
inserted from the top and the lock nuts are
on the bottom. Use the inside hole on the
stand base for 24width. Use the outside
hole for 22width.
2
Attach the other end of the bracket to the
upper rear hole of the other stand base the
same way. Use the inside hole on the stand
base for 24width or the outside hole for
22width. Hand-tighten the screws and
nuts.
Bracket
Type A Screw
Lock
Nut
Use outside
holes for
22models
Use inside
holes for
24models
Wall
Mounting
Bracket
Cross
Brace
Diagonal
Brace
Stand Bases


Produkt Specifikationer

Mærke: GE
Kategori: Tørretumbler
Model: DSR24RWWH

Har du brug for hjælp?

Hvis du har brug for hjælp til GE DSR24RWWH stil et spørgsmål nedenfor, og andre brugere vil svare dig




Tørretumbler GE Manualer

GE

GE GTD58GBPVDG Manual

17 Juni 2025
GE

GE GTD58EBPVDG Manual

17 Juni 2025
GE

GE HTX26GASWWW Manual

21 Februar 2025
GE

GE GTD42EASJWW Manual

17 Januar 2025
GE

GE GFDN110EDWW Manual

17 Januar 2025
GE

GE GFD45GSSKWW Manual

17 Januar 2025
GE

GE GFD45GSPKDG Manual

17 Januar 2025
GE

GE GTX42GASJWW Manual

9 Januar 2025
GE

GE GTDS855EDMC Manual

9 Januar 2025

Tørretumbler Manualer

Nyeste Tørretumbler Manualer