GE GHDS360EFWW Manual

GE Tørretumbler GHDS360EFWW

Læs gratis den danske manual til GE GHDS360EFWW (2 sider) i kategorien Tørretumbler. Denne vejledning er vurderet som hjælpsom af 89 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 45 anmeldelser. Har du et spørgsmål om GE GHDS360EFWW, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
quick installation guide
Instructions en Français - Voir le • Instrucciones en Español - Ver el Manuel d’utilisation et d’installation Manual del propietario e instalación
This quick reference guide is provided for informational purposes only and does not replace, modify or change in any manner the .Owner’s Manual & Installation Instructions
WARNING
DO NOT DISCARD. RE IN FOR FUTURE USTA E.
STOP
• Clothes dryer installation must be performed by a qualified installer.
• Install the clothes dryer according to the Owner’s Manual & Installation
Instructions and in accordance with local codes.
• DO NOT install or store this appliance in any location where it could be
exposed to water and/or weather.
• The dryer be exhausted to the outdoors.MUST
NOTE: This appliance must be properly grounded and installed as described
in these steps and the Owner’s Manual. Electrical service to the dryer must
conform with local codes and ordinances and the latest edition of the National
Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1. Gas
installations must conform with local codes, or in the absence of local codes,
with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and
Propane Installation Code, CSA B149.1.
TOOLS NEEDED
r Slip-joint pliers
r Flat-blade
screwdriver
r Phillips
screwdriver
r Level
r 8” Pipe wrench
(Gas models
only)
r 10” Adjustable
wrenches (2)
(Gas models
only)
PARTS SUPPLIED
r
Water hoses (2)
r “Y” Connector
• Determine the type of
outlet available for your
dryer (3 or 4 prong).
• Turn off the dryer’s circuit
breaker or remove the
dryer’s circuit fuse at the
electrical box.
• Remove power cord cover
located at bottom right.
• Connect wires as shown
for applicable outlet type.
• Properly secure power
cord at strain relief.
• Reinstall the cover.
• Rock the dryer into its
final location and place a
level on top.
• Adjust the front leveling
legs up or down using an
adjustable wrench.
• Level the dryer both side-
to-side and front-to-back.
• If your dryer is on a riser,
turn lock nuts up towards
the base of the dryer
and tighten with the
adjustable wrench.
• Ensure that a shut-off valve is installed.
•
If connected to LP gas, have a qualified person make sure
the gas pressure does not exceed 13” water column.
• Always use a new CSA International approved flexible
gas supply line. Never re-use old flexible connectors.
• Securely tighten all gas connections as shown with
a pipe and adjustable wrench. Use pipe thread
compound appropriate for natural or LP gas, or use
Teflon® tape.
• Open the gas shut-off valve.
• Check all connections for leaks with soapy solution or
equivalent.
• If leaks are found, close the gas shut-off valve,
re-tighten the joint and repeat.
• If desired, the door swing
direction can be reversed on
your dryer.
• Please follow the door
reversal instructions in your
Owner’s Manual & Installation
Instructions.
• Plug your dryer into a
grounded outlet. Do not use
an extension cord or adaptor
plug.
3Connect
power cord
6Level the
dryer 7Reverse dryer door swing (if desired)
and plug the dryer in
4Connect dryer to gas supply
(Gas models only)
1Unpack your dryer &
tools and materials needed
r 4” dia. metal elbow
r 3/4” strain relief (UL recognized)
r 4” duct clamps (2) or 4” spring clamps (2)
r Safety glasses and gloves
r 4” dia. metal duct (recommended)
r
4” dia., UL-listed flexible metal duct (if needed)
r Exhaust hood
r Duct tape
r Dryer power cord kit (not provided with
dryer) UL rated 120/240V, 30A with 3 or
4 prongs. Identify plug type as per house
receptacle before purchasing line cord.
r Pipe compound
r Flexible gas line connector
r Soap solution for leak detection
r
Owner’s Manual
& Installation
Instructions
• Dryer must always be
exhausted to the outdoors.
• For best drying performance,
a rigid metal transition duct
is recommended. If rigid
metal duct cannot be used,
then UL-listed flexible metal
(semi-rigid) ducting can be
used.
• Please refer to the Owner’s
Manual & Installation
Instructions for installation
venting requirements as
well as instructions for side/
bottom venting conversions.
• Main power is turned on.
• The dryer is plugged in.
• Dryer power cord is securely and correctly connected.
• Hoses are securely connected.
• Faucets are turned on.
• Dryer is securely connected to the home vent and is exhausting to the outdoors.
•
On gas models, gas supply is securely connected and has been checked for leaks.
• Run a load of garments in the cycle.Time Dry
• When the load is tumbling, ensure that the dryer and leveling legs are stable.
• If necessary, adjust the front leveling legs while the dryer is still tumbling until
the dryer is properly leveled.
• Stop the unit after 5 minutes by opening the door and check the garments to
ensure they are warm.
8Final installation checklist
and test cycle
5Connect the dryer
exhaust duct
2Connect hoses
to the dryer
• Turn the cold water faucet off and
remove the washer inlet hose from
the washer fill valve.
• Connect hoses as shown ensuring
that rubber flat washers and filter
screens are placed as required.
Hand tighten all connections and
then tighten them another 2/3 turn
with pliers.
• Turn on the water faucet and check
for leaks around the “Y” connector,
faucet, and hose couplings.
• Ensure hoses do not become kinked
when moving the dryer into it’s final
position.
To Cold Water
Faucet
To Dryer Water
Valve
To Washer
Cold Water
Valve
Filter Screen
Water Inlet Hose
Short Hose
Rubber Flat Washer
Long Hose
Rubber Flat
Washer
Remove link
and discard.
Link
Green Ground
Screw
Hot
Hot
Neutral (White)
Hot
Hot
Neutral (White)
3-Wire Connection:
4-Wire Connection:
Relocate
green
ground
screw
here.
Green
Wire
OR
Elbow
Adapter
Items not supplied
Adapter
1/8” NPT
Pipe
Plug for
Checking
Gas Inlet
Pressure
Shut-Off
Valve
Pipe size at
least 1/2”
3/8” NPT
New Metal Flexible
Gas Line Connector
• DO cut duct as short as possible
and install straight into wall. • DO use elbows when
turns are necessary.
Elbows
• DO NOT use
excessive
exhaust length.
Cut duct
as short as
possible.
• DO NOT
crush duct
against the
wall.
• DO NOT set
dryer on duct.
• DO NOT bend or
collapse ducting.
Use elbows if turns
are necessary.
DO
NOT:
DO:
LowerRaise Ensure
proper
ground
exists
before
use.
Ensure
proper
ground
exists
before
use.
241D1745P001 31-16707-1 02-13 GE

Produkt Specifikationer

Mærke: GE
Kategori: Tørretumbler
Model: GHDS360EFWW

Har du brug for hjælp?

Hvis du har brug for hjælp til GE GHDS360EFWW stil et spørgsmål nedenfor, og andre brugere vil svare dig


Tørretumbler GE Manualer

GE

GE GFD35GSPYDS Manual

10 November 2025
GE

GE Profile PTD80EBPTRS Manual

5 November 2025
GE

GE Profile PTD80GBPTRS Manual

4 November 2025
GE

GE GFP1528 Manual

21 August 2025
GE

GE PFD95GSPWGN Manual

21 August 2025
GE

GE GFR0728 Manual

21 August 2025
GE

GE SPLK30N01A Manual

20 August 2025
GE

GE Profile PFD87ESPVRS Manual

7 August 2025
GE

GE Profile PFD87GSSVWW Manual

7 August 2025
GE

GE Profile PFD87ESSVWW Manual

6 August 2025

Tørretumbler Manualer

Nyeste Tørretumbler Manualer

Saba

Saba DR9HPDW Manual

12 November 2025
Whirlpool

Whirlpool C WD 85M WBS BE Manual

11 November 2025
Electrolux

Electrolux DE-6100 Manual

11 November 2025
Bosch

Bosch WTH83V94 Manual

11 November 2025
Bosch

Bosch WQG2450R11 Manual

11 November 2025
Siemens

Siemens WT45HV0BDN Manual

10 November 2025
Bosch

Bosch WQG133DANL Manual

10 November 2025
Bosch

Bosch WTH85V94 Manual

10 November 2025
Bosch

Bosch WNG24442 Manual

10 November 2025
Bosch

Bosch WQG233DR91 Manual

10 November 2025