GE GPF375 Manual
GE
Opvaskemaskine
GPF375
Læs gratis den danske manual til GE GPF375 (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9 anmeldelser. Har du et spørgsmål om GE GPF375, eller vil du spørge andre brugere om produktet?
Side 1/8
18-15/16"
23-5/8"
3/4" Thick Panel
Appearance Side
1-9/16"
3/4"
1/2"
A*
23-5/8"
3/4" Thick Access Panel
Installation
Instructions
3/4" Custom Dishwasher
Door and Access Panel Kit
GPF375 Kit
Note: The custom wood
access panel should
evenly match the bottom
of adjacent cabinets.
Adjustments made to the
leveling legs to obtain
correct height can affect
the vertical dimension
(height) of the access
panel.
1 CUT 3/4" THICK CUSTOM
PANELS TO SIZE
• Cut the 3/4" thick door panel to the dimen-
sions shown.
• Rout the bottom edge of the door panel on
the appearance side, 1/2" deep and 1-9/16"
high resulting in 1/4" thickness. See
illustration.
• The access panel height may be 3-3/4" to
4-1/4" max. The access panel height can vary
depending upon toekick height and adjust-
ments made to the leveling legs.
*3-3/4" min., 4-1/4" max. for typical 4" toekicks.
Adjustments may be required to match adjacent cabinet
fronts.
WARNING:
To prevent electric shock, disconnect electrical
power supply to dishwasher before changing
panels. Do not operate dishwasher while
changing panels or when lower access panel
assembly is removed.
Before you begin
Read these instructions completely
and carefully.
IMPORTANT – Save these instructions
for local inspector’s use.
IMPORTANT – Observe all governing
codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions
with your Owner’s Manual for future
reference.
STOP
TOOLS AND MATERIALS REQUIRED:
• 1/4" socket driver
• Phillips screwdriver
• Electric drill
• 1/8" and 3/16" drill bits
• Carpenters square
• Safety Glasses
The custom panels should be constructed in
the same manner as cabinet doors. Cut edges
can be seen and must be finished for the best
appearance.
The GPF475 Trim Kit provides for the installa-
tion of 3/4" thick custom door and access
panels with a typical 4" high toekick.
KIT INCLUDES:
• Door panel support
• 7, 5/8" phillips flat head screws
• 3 round head screws
• GPF100 spring kit
2 REMOVE LOWER ACCESS
PANEL ASSEMBLY
• Remove the two screws below the access
panel. Retain screws.
• Loosen the two screws located between the
door and the access panel. Do not attempt
to remove these screws. They are secured
to the access panel with washers.
• Remove the access panel assembly and
toekick from the dishwasher. Set aside.
NOTE: Do not remove the insulation behind
the access panel or toekick.
3 MOUNT CUSTOM PANEL TO
METAL SUPPORT PANEL
A
• Place the metal door panel support on the
custom panel, with the projecting tabs
overlapping and against the bottom edge.
Center the support panel by matching the
center line to the diamond cutout.
NOTE: Do not remove tape from adhesive
strips.
• Mount custom panel to metal support panel
• Lay the custom panel on a flat surface with
appearance side down.
• Measure and mark the center line. Use a
carpenters square to draw the center line.
C
• Remove the custom panel from the support.
• Remove tape from adhesive strips on the
metal support – on the side that touches the
custom panel.
• Carefully, position the metal support onto the
custom panel with center line showing
through the diamond. Press the metal sup-
port against the panel.
B
2
Loosen 2 Screws
Escutcheon
Door
Panel
Access Panel
Toekick
Foam
Double Sided
Tape
Tab
Tabs
Overlap
Bottom
Edge
Metal Support
Overlaps
Top
Edge
Remove
Tape Covering
Adhesive Strips
Produkt Specifikationer
| Mærke: | GE |
| Kategori: | Opvaskemaskine |
| Model: | GPF375 |
Har du brug for hjælp?
Hvis du har brug for hjælp til GE GPF375 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Opvaskemaskine GE Manualer
9 Januar 2025
9 Januar 2025
9 Januar 2025
9 December 2024
9 December 2024
9 December 2024
9 December 2024
9 December 2024
9 December 2024
9 December 2024
Opvaskemaskine Manualer
- Freggia
- Elektra Bregenz
- Jackson
- Kaiser
- Cove
- Eurotech
- Eurom
- AEG-Electrolux
- WLA
- Veripart
- IFB
- Ansonic
- BLANCO
- Thor
- Asko
Nyeste Opvaskemaskine Manualer
23 Juni 2025
23 Juni 2025
23 Juni 2025
22 Juni 2025
22 Juni 2025
22 Juni 2025
22 Juni 2025
22 Juni 2025
22 Juni 2025
22 Juni 2025