GE GPF475 Manual

GE Opvaskemaskine GPF475

Læs gratis den danske manual til GE GPF475 (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 18 anmeldelser. Har du et spørgsmål om GE GPF475, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

IMPORTANT – Save these instruc-

tions for local inspector’s use.

IMPORTANT – Observe all governing

codes and ordinances.

Note to Installer – Be sure to leave these

instructions with the Consumer.

Note to Consumer – Keep these instructions

with your Owner’s Manual for future

reference.

Installation

Instructions

3/4" Custom Dishwasher

Door and Access Panel Kit

GPF475 Kit

WARNING:

To prevent electric shock, disconnect

electrical power supply to dishwasher before

changing panels. Do not operate dishwasher

while changing panels or when lower access

panel assembly is removed.

TOOLS AND MATERIALS REQUIRED:

• 1/4" socket driver

• Phillips screwdriver

• Electric drill

• 1/8" and 3/16" drill bits

• Carpenters square

• Safety Glasses

The custom panels should be constructed in

the same manner as cabinet doors. Cut edges

can be seen and must be finished for the best

appearance.

The GPF475 Trim Kit provides for the installa-

tion of 3/4" thick custom door and access

panels with a typical 4" high toekick.

KIT INCLUDES:

• Door panel support

• 7, 5/8" phillips flat head screws

• 3 round head screws

• GPF100 spring kit

STOP

1 CUT 3/4" THICK CUSTOM

PANELS TO SIZE

CAUTION:

Verify door panel height before cutting the

custom panel. Measure from the bottom of the

escutcheon to the bottom of the door. Some

models require shorter door panels.

• Cut the 3/4" thick door panel to the

dimensions shown. (19-13/16" or 19-3/8"H x

23-5/8"W.)

• Rout the bottom edge of the door panel on

the appearance side, 1/2" deep and 1-9/16"

high resulting in 1/4" thickness. See

illustration.

CAUTION:

Some models require 19-3/8" panel height.

Measure before cutting the panel.

Note:

The custom wood

access panel should

evenly match the

bottom of adjacent

cabinets. Adjustments

made to the leveling

legs to obtain correct

height can affect the

vertical dimension

(height) of the access

panel.

19-13/16"

23-5/8"

3/4" Thick Panel

Appearance Side

1-9/16"

3/4"

1/2"

2 REMOVE LOWER ACCESS

PANEL ASSEMBLY

• Remove the two screws below the access

panel. Retain screws.

• Loosen the two screws located between the

door and the access panel. Do not attempt

to remove these screws. They are secured

to the access panel with washers.

• Remove the access panel assembly and

toekick from the dishwasher. Set aside.

NOTE: Do not remove the insulation behind

the access panel

or toekick.

3 MOUNT CUSTOM PANEL TO

METAL SUPPORT PANEL

• Place the metal door panel support on the

custom panel, with the projecting tabs

overlapping and against the bottom edge.

Center the support panel by matching the

center line to the diamond cutout.

NOTE: Do not remove tape from adhesive

strips.

• Lay the custom panel on a flat surface with

appearance side down.

• Measure and mark the center line. Use a

carpenters square to draw the center line.

• Remove the custom panel from the support.

• Remove tape from adhesive strips on the

metal support – on the side that touches the

custom panel.

• Carefully, position the metal support onto the

custom panel with center line showing

through the diamond. Press the metal sup-

port against the panel.

1 CUT 3/4" THICK CUSTOM

PANELS TO SIZE (CONTINUED)

• The access panel height may be 3-3/4" to

4-1/4" max. The access panel height can vary

depending upon toekick height and adjust-

ments made to the leveling legs.

*3-3/4" min., 4-1/4" max. for typical 4" toekicks.

Adjustments may be required to match adjacent cabinet

fronts.

23-5/8"

3/4" Thick Access Panel

Loosen 2 Screws

Escutcheon

Door

Panel

Access Panel

Toekick

Foam

Double Sided

Tape

Tab

Tabs

Overlap

Bottom

Edge

Metal Support

Overlaps

Top

Edge

Remove

Tape Covering

Adhesive Strips

Produkt Specifikationer

Mærke:	GE
Kategori:	Opvaskemaskine
Model:	GPF475

Har du brug for hjælp?

Hvis du har brug for hjælp til GE GPF475 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Opvaskemaskine GE Manualer

GE CDT828P2VS1 Manual

7 August 2025

GE CDT888P4VW2 Manual

7 August 2025

GE CDT858P3VD1 Manual

7 August 2025

GE CDT858P4VW2 Manual

6 August 2025

GE GDF540HSFSS Manual

28 Juli 2025

GE PDT760SSFSS Profile Manual

28 Juli 2025

GE GDWF460VSS Manual

28 Juli 2025

GE Spacemaker GSM2200VWW Manual

28 Juli 2025

GE GDT550HGDWW Manual

28 Juli 2025

GE EDW2060 Manual

27 Juli 2025

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Barazza 1LVE6I Manual

12 September 2025

Robinhood DWM12P6FSS Manual

12 September 2025

Siemens SK25210EU Manual

12 September 2025

Fagor 4LVF-435AD Manual

12 September 2025

Siemens SN46M293SK Manual

11 September 2025

Gorenje GV693A60UVAD Manual

11 September 2025

Bosch SMS40E38EU Manual

11 September 2025

Hoonved C 60 D E Manual

10 September 2025

LG TrueSteam Manual

10 September 2025

Hoonved C 46 D E Manual

10 September 2025