GE GPF875W Manual

GE Opvaskemaskine GPF875W

Læs gratis den danske manual til GE GPF875W (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 19 anmeldelser. Har du et spørgsmål om GE GPF875W, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT – Save these instruc-
tions for local inspector’s use.
IMPORTANT – Observe all governing
codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions
with your Owner’s Manual for future
reference.
Installation
Instructions
3/4" Custom Dishwasher
Door Panel Kit
GPF875 Series Kits
GPF875B-Black Trim Kit,
GPF875C-Bisque Trim Kit, GPF875W-White Trim Kit
TOOLS AND MATERIALS REQUIRED:
• Electric drill
• 1/8" drill bit
• Carpenters square
• Safety glasses
• Gloves to protect against sharp edges
• Stubby Phillips screwdriver
The custom panels should be constructed in
the same manner as cabinet doors. Cut edges
can be seen and must be finished for the best
appearance.
KIT INCLUDES:
STOP
Panel Support
9 Phillips Head
Screws, 5/8" Long
2 Door Springs
To Be Used On All Models
Except PDW8500
2 Door Springs
PDW8500 Only
WARNING:
To prevent electric shock, disconnect electri-
cal power supply to dishwasher before
changing panels. Do not operate dishwasher
while changing panel.
CAUTION:
On new installations, do not remove wood
base until you are ready to install the dish-
washer. The dishwasher will tip over when
the door is opened.
Bottom
Phillips Screws
2 REMOVE DOOR PANEL
2
Figure 2 Figure 3
• Open dishwasher door.
• Remove the 6 screws along the sides of the
door (Figure 2) holding the inner door to the
outer panel. Retain screws.
• Close the door.
• Remove the two screws at the bottom of the
door panel (Figure 3). Retain screws.
• Remove door panel.
Figure 4
3 ASSEMBLE DOOR PANEL
• Remove the protective plastic covering from
the support panel trim.
• Place the custom panel appearance side
down on a flat protected surface. Take care
not to scratch the custom panel or the trim.
• Place the support panel on the back side of
the custom panel such that the top bend fits
into the routed groove. The support panel
and custom panel should be evenly aligned
side to side.
• Select and mark screw holes in the metal
panel where the wood beneath is at least
3/4" thick.
• Use 1/8" bit to drill pilot holes, 5/8" deep
through the support and into the wood
panel at the marked screw holes.
• Secure the wood to the panel with the
screws provided.
CAUTION:
Do not drill pilot holes too deeply to avoid
damaging the appearance side of the panel.
1 PREPARE 3/4" CUSTOM PANEL
• The custom panel must be sized to the
dimensions shown.
• Rout the top edge of the door panel on the
back side as shown in Figure 1:
– 1/4" deep and 3/8" wide.
– 20" wide (flat surface)
and 1-7/8" from
each side.
Note: The custom
wood panel should
evenly align with the
bottom of adjacent
cabinets. Figure 1
Routed Groove Custom Panel
Drill 1/8" Holes
Support
Panel Trim
Top
Bend
25-7/16"
23-3/4"
3/4" Thick Panel
Appearance Side
1-7/8"
1-7/8"
20" Min.
Flat Surface
Rout 1/4" Deep,
3/8" Wide
3/4"
Back Side
of Panel
1/4" Deep
3/8" Wide

Produkt Specifikationer

Mærke: GE
Kategori: Opvaskemaskine
Model: GPF875W

Har du brug for hjælp?

Hvis du har brug for hjælp til GE GPF875W stil et spørgsmål nedenfor, og andre brugere vil svare dig


Opvaskemaskine GE Manualer

GE

GE PDW1800KBB Manual

9 Januar 2025
GE

GE GSD5360 Manual

9 Januar 2025
GE

GE GSD5132 Manual

9 Januar 2025
GE

GE GDF520PSJSS Manual

9 December 2024
GE

GE GDF520PGJWW Manual

9 December 2024
GE

GE CDT865SMJDS Manual

9 December 2024
GE

GE GDF510PMJSA Manual

9 December 2024
GE

GE GSD5122 Manual

9 December 2024
GE

GE GSD4060KSS Manual

9 December 2024
GE

GE GSD4010 Manual

9 December 2024

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Kernau

Kernau KFDW 6753 X Manual

14 Juni 2025
Jackson

Jackson Conserver XL-E Manual

14 Juni 2025
Kernau

Kernau KDI 4753 SAD Manual

14 Juni 2025
Champion

Champion DH6000 VHR Manual

14 Juni 2025
Jackson

Jackson DishStar ADA-SEER Manual

14 Juni 2025
Asko

Asko DBI344IB.S Manual

14 Juni 2025
Champion

Champion CG208 Manual

14 Juni 2025
CMA Dishmachines

CMA Dishmachines H-1X Manual

14 Juni 2025
Jackson

Jackson DishStar HT Manual

14 Juni 2025
Bosch

Bosch SMS6IKI00I Manual

14 Juni 2025