GE GTDP301GLWS Manual

GE Tørretumbler GTDP301GLWS

Læs gratis den danske manual til GE GTDP301GLWS (9 sider) i kategorien Tørretumbler. Denne vejledning er vurderet som hjælpsom af 55 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 28 anmeldelser. Har du et spørgsmål om GE GTDP301GLWS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

WARNING RISK OF FIRE

• To reduce the risk of severe injury or death, follow all installation instructions.

• Clothes dryer installation must be performed by a qualied installer.

• Install the clothes dryer according to these instructions and in accordance with local

codes. In the absence of local codes, installation must comply with National Fuel Gas

Code, ANSIZ223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code,

CSA B149.1.

• California Safe Drinking Water and Toxic Enforcement Act.

This act requires the governor of California to publish a list of substances known to the

state to cause cancer, birth defects or other reproductive harm and requires businesses

to warn customers of potential exposure to such substances. Gas appliances can

cause minor exposure to four of these substances, namely benzene, carbon monoxide,

formaldehyde and soot, caused primarily by the incomplete combustion of natural gas

or LP fuels. Properly adjusted dryers will minimize incomplete combustion. Exposure

to these substances can be minimized further by properly venting the dryer to the

outdoors.

• This dryer must be exhausted to the outdoors.

• Use only 4” rigid metal ducting for exhausting the clothes dryer to the outdoors.

• install a clothes dryer with exible plastic ducting materials. If exible metal DO NOT

(semi-rigid or foil-type) duct is installed, it must be UL listed and installed in accordance

with the instructions found in “Connecting The Dryer To House Vent” on page 6 of this

manual. Flexible venting materials are known to collapse, be easily crushed, and trap

lint. These conditions will obstruct dryer airow and increase the risk of re.

• Do not install or store this appliance in any location where it could be exposed to water

and or weather.

• Dryers installed in residential garages must be elevated 18” (46 cm) above the oor.

• Save these instructions. (Installers: Be sure to leave these instructions with the

customer).

In the state of Massachusetts, installation must be performed by a qualiedor

licensed contractor, plumber, or gastter qualied or licensed by the state.

Installation

Instructions

Gas Dryer

Questions on Installation? Call: 1-800-GECARES (US)

or Visit our Web site at: www.GEAppliances.com (US)

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•IMPORTANT- Save these instructions for

local inspector’s use.

•IMPORTANT- Observe all governing codes

and ordinances.

• Be sure to leave these Note to Installer -

instructions with the customer.

• Keep these instructions Note to Customer -

with your Use and Care Book for future

reference.

• Before the old dryer is removed from service or

discarded, remove the dryer door.

• Inspect the dryer exhaust outlet and straighten

the outlet walls if they are bent.

• Service information and the wiring diagram

are located in the control console.

• Do not allow children on or in the appliance.

Close supervision of children is necessary when

the appliance is used near children.

• Install the dryer where the temperature is

above 50°F for satisfactory operation of the

dryer control system.

LEVEL

8" PIPE WRENCH

10" ADJUS TABLE WRENCHES

(x2)

TOOLS YOU

WILL NEED

SLIP JOINT PLIERS FLAT BLADE SCREWDRIVER

M ATERIALS YOU WILL NEED

EXHAUST HOOD

FLEXIBLE GAS LINE CONNECTOR

SOAP SOLUTION

FOR LEAK DETECTION

PIPE

COMPOUND

DUCT TAPE

GLOVES

SAFETY GLASSES

4" DIAM METAL ELBOW

4" DUCT CLAMPS

4" SPRING CLAMPS

(x2)

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT

(IF NEEDED)

KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT

(IF NEEDED.)

234D1113P002 31-16225-1 07/08/10 GE

Step 1 Verify Your Gas Installation (see section 2).

Step 2 Prepare the Area and Exhaust for Installation of

New Dryer (see section 1).

Step 3 Check and Insure the Existing External Exhaust

is Clean (see section 1) and Meets Attached

Installation Specications (see section 6).

Step 4 Remove the Foam Shipping Pads (see section 1).

Step 5 Move the Dryer to the Desired Location.

Step 6 Level Your Dryer (see section 8).

Step 7 Connect the Gas Supply (see section 3) and check

for leaks (see section 4).

Step 8 Connect the External Exhaust (see section 7).

Step 9 Connect the Power Supply (see section 5).

Step 10 Check the Operation of the Power Supply, Gas

Connections, and Venting.

Step 11 Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By the Owner.

For Alcove or Closet Installation see section 9.

For Bathroom or Bedroom Installation see section 10.

For Mobile or Manufactured Home see section 11.

Installation Instructions

Minimum Clearance Other Than Alcove or Closet Installation

Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and 1 in. rear.

Consideration be given to provide adequate clearance for installation and service. must

2 GAS REQUIREMENTS

WARNING

• Installation must conform to local codes and

ordinances, or in their absence, the NATIONAL FUEL

GAS CODE, ANSI Z223.

• This gas dryer is equipped with a Valve & Burner

Assembly for use only with natural gas. Using

conversion kit WE25X0217, your local service

organization can convert this dryer for use with

propane (LP) gas. ALL CONVERSIONS MUST BE MADE BY

PROPERLY TRAINED AND QUALIFIED PERSONNEL AND

IN ACCORDANCE WITH LOCAL CODES AND ORDINANCE

REQUIREMENTS.

• The dryer must be disconnected from the gas supply

piping system during any pressure testing of that

system at a test pressure in excess of 0.5 PSI (3.4 KPa).

• The dryer must be isolated from the gas supply piping

system by closing the equipment shut-o valve during

any pressure testing of the gas supply piping of test

pressure equal to or less than 0.5 PSI (3.4 KPa).

GAS SUPPLY

• A 1/8-in.National Pipe Taper thread plugged tapping,

accessible for test gauge connection, must be installed

immediately upstream of the gas supply connection to

the dryer. Contact your local gas utility should you have

questions on the installation of the plugged tapping.

• Supply line is to be 1/2-in. rigid pipe and equipped with an

accessible shut-off within 6 ft. of, and in the same room

with the dryer.

•Use pipe thread sealer compound or Teon tape appropri-

ate for natural or LP gas.

• You must use with this dryer a exible metal connector

listed connector ANSI Z21.24 / CSA 6.10. The length of the

connect shall not exceed 3 ft.

• Connect exible metal connector to dryer and gas supply.

• Open shut-off valve.

INTERNAL DUCT

OPENING CHECK THA T EXHAUST

HOOD DAMPER OPENS

AND CLOSES FREE LY.

WALL

TILT THE DRYER SIDEWAYS

AND REMOVE THE FOAM

SHIPPING PADS BY

PULLING AT THE SIDES

AND BREAKING THEM

AWAY FROM THE DRYER

LEGS. BE SURE TO

REMOVE ALL OF THE

FOAM PIECES AROUND

THE LEGS.

1 PREPARING FOR INSTALLATION

OF NEW DRYER

TIP: Install your dryer before installing your washer.

This will allow better access when installing dryer

exhaust.

DISCONNECTING GAS

REMOVING LINT FROM WALL

EXHAUST OPENING

• Remove and discard existing plastic or metal foil

transition duct and replace with UL listed transition

duct.

DISCONNECT AND DISCARD OLD

FLEXIBLE GAS CONNECTOR AND

OLD TRANSITION DUCTING

MATERIAL. REPLACE WITH NEW

CSA(AGA) APPROVED FLEXIBLE

GAS LINE CONNECTOR AND UL

APPROVED TRANSITION DUCT.

TURN GAS

SHUT-OFF VALVE

TO THE OFF

POSITION.

WARNING - NEVER REUSE OLD

FLEXIBLE CONNECTORS.

The use of old exible connectors can cause leaks and

personal injury. Always use new exible connectors

when installing gas appliances.

DR YER GAS SUPPLY CONNECTION

2-5/8" 3/8" NPT MALE THREAD GAS SUPPLY

NOTE: Add to vertical dimension

the distance between cabinet

bottom to floor.

Produkt Specifikationer

Mærke:	GE
Kategori:	Tørretumbler
Model:	GTDP301GLWS

Har du brug for hjælp?

Hvis du har brug for hjælp til GE GTDP301GLWS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Tørretumbler GE Manualer

GE Profile PFD87ESPVRS Manual

7 August 2025

GE Profile PFD87GSSVWW Manual

7 August 2025

GE Profile PFD87ESSVWW Manual

6 August 2025

GE GTD38GASWWS Manual

6 August 2025

GE GFMS175EHDG Manual

27 Juli 2025

GE Profile PFA18REVW Manual

8 Juli 2025

GE Profile DPSB519GBCC Manual

30 Juni 2025

GE GTD58GBPVDG Manual

17 Juni 2025

GE GTD58EBPVDG Manual

17 Juni 2025

GE HTX26GASWWW Manual

21 Februar 2025

Tørretumbler Manualer

Nyeste Tørretumbler Manualer

Candy ROE C8TCER-ZA Manual

14 August 2025

Candy CSOE C10TREX-47 Manual

14 August 2025

Candy CSOE C9TEX-47 Manual

14 August 2025

Candy CRO4 H7A2TE-S Manual

14 August 2025

Hoover HBWM 815TH-S Manual

14 August 2025

Candy ROE H11A2TCER-ZA Manual

14 August 2025

Candy RPE H9A3TE-S/N Manual

14 August 2025

Candy CSOE H9A2DBEB-S Manual

14 August 2025

Hoover NDEH10A2TCBES-84 Manual

14 August 2025

Candy RPE H9A3TE-S Manual

14 August 2025