GE JX1530MWW Manual

GE Magnetron JX1530MWW

Læs gratis den danske manual til GE JX1530MWW (4 sider) i kategorien Magnetron. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 8 anmeldelser. Har du et spørgsmål om GE JX1530MWW, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
PARTS INCLUDED
NOTE: This kit has extra screws to prevent the
technician from spending extra time locating a
replacement screw during installation.
PART QUANTITY
❒ Trim Frame 1
❒ Bottom Duct 1
❒ Top Bracket 1
❒ Bottom Bracket 1
❒ Upper Duct 1
❒ Rear Duct 1
❒ 4 mm x 14 mm 22 required
Round-Head 2 extra
Screws
❒ 4 mm x 14 mm 4 required
Flat-Head 2 extra
Screws
❒ Anti-Tip Brace 1
❒ Anti-Tip Bracket 1
❒ Template 1
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Built-In Trim Kits
Instructions JX1527 JX1530
1
❒
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT —Save these instructions
for local inspector’s use.
•IMPORTANT —Observe all governing
codes and ordinances.
•Note to Installer – Be sure to leave these
instructions with the Consumer.
•Note to Consumer – Keep these instructions for
future reference.
•Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
•Completion time – 1 to 3 hours
•Proper installation is the responsibility of the
installer.
•Product failure due to improper installation is not
covered under the Warranty.
•This kit is UL listed for installation alone
or over any GE/GE Profile single electric wall oven.
•For easier installation and personal safety, we
recommend that two people install this microwave
oven.
•Unplug the microwave oven before attempting
installation of this kit.
•This kit is for use on models: PEB1590DMBB,
PEB1590DMWW and PEB1590SMSS.
•Do not alter or modify any part of this kit or the
oven.
WARNING —This oven must
be plugged into a properly grounded 3-hole, 120V
receptacle as required by the National Electrical Code.
FOR YOUR SAFETY:
WARNING —Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the
service disconnecting means cannot be locked,
securely fasten a prominent warning device,
such as a tag, to the service panel.
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
TOOLS YOU WILL NEED
2
Installation Instructions
❒ #2 Phillips Screwdriver
❒ Tape Measure
❒ Drill with 7/64″Bit or #35
❒ Scissors (Optional)
❒ Pencil
❒ Awl or Punch
❒
CUTOUT DIMENSIONS
WARNING — This trim kit uses air
flow from the top, bottom and sides of the
trim frame. Blocking the air flow can cause
the microwave to function improperly and
may cause damage to the microwave.
Allow a 1″clearance beyond the edge of the
trim frame to provide proper air flow.
1
Depth
Height
11⁄2″Overlap
Width
11⁄2″Overlap
1″Clearance
beyond trim frame
(on all sides)
3″Min.
27″Models: 1
1⁄2″overlap
30″Models: 3″overlap
❒
CUTOUT DIMENSIONS (CONT.)
On 27″models, allow 11⁄2″on all sides for
overlap of the trim frame over the edges of
the cutout.
On 30″models, allow 11⁄2″at the top and
bottom and 3″ on each side for overlap of
the trim frame over the edges of the cutout.
FOR INSTALLATION ABOVE A
BUILT-IN OVEN:
Microwave oven should be installed on a 3/8″
plywood base and supported by 2x4 or 1x2
equivalent runners on all sides. Base must be
capable of supporting a minimum of 100 lbs.
1
*Min. depth with 120V–60 Hertz grounded power
receptacle outside cabinet 211⁄2″
Min. depth with 120V–60 Hertz grounded power
receptacle inside cabinet 23″
Models 27″30″
Height 183⁄4″183⁄4″
Width 24″±1⁄ ±16″24″1⁄16″
Depth (min.)* 211⁄2″or 23″211⁄2″or 23″
❒
INSTALL THE ANTI-TIP BRACE
Draw a line on the cutout floor at the
center of the cutout, and extend the line
1/2″down the face of the cabinet.
Fold or cut the front edge of the template,
along the front guide line. Place the
template flush along the front edge of the
cutout floor, aligning the center line of
the template with the center line of the
cutout floor. Mark the centers of the two
screw holes with an awl or center punch
for the anti-tip brace location as shown.
Remove the
template and drill
two holes for the
anti-tip brace.
Install the anti-tip
brace onto the
cutout floor using
two round-head
screws.
D
C
B
A
2
Round-Head
Screws
Anti-Tip
Brace
Cutout
Floor
Center
Line
BA
C
DIMENSIONS:
A = 13⁄16″
B = 3″
C = 201⁄16″
❒ Level

Produkt Specifikationer

Mærke: GE
Kategori: Magnetron
Model: JX1530MWW

Har du brug for hjælp?

Hvis du har brug for hjælp til GE JX1530MWW stil et spørgsmål nedenfor, og andre brugere vil svare dig


Magnetron GE Manualer

GE

GE GCST09U1 Manual

9 Januar 2025
GE

GE UVM9125STSS Manual

30 December 2025
GE

GE PVM9215DFWW Manual

29 December 2024
GE

GE Profile PVM9195DFCC Manual

29 December 2024
GE

GE JVM6175SFSS Manual

29 December 2024
GE

GE JX9152ELDS Manual

27 December 2024
GE

GE JX827BMTS Manual

27 December 2024
GE

GE Café CSA1201RSS Manual

15 December 2024
GE

GE JX7227BLTS Manual

8 December 2024
GE

GE JX1530SMSS Manual

8 December 2024

Magnetron Manualer

Nyeste Magnetron Manualer

Creda

Creda 29032 Manual

4 April 2025
Smeg

Smeg FMIA120B3 Manual

1 April 2025
Candy

Candy CMGA 30DBST Manual

29 Marts 2025
Candy

Candy CAMW25X Manual

29 Marts 2025
Hisense

Hisense H25MOBS7HUK Manual

29 Marts 2025
Toshiba

Toshiba MWP-MM20P(WH) Manual

27 Marts 2025
Whirlpool

Whirlpool WMN461BXF Manual

4 Marts 2025
LG

LG MSER1130B Manual

3 Marts 2025
Hotpoint

Hotpoint HCW6O7HTS Manual

27 Februar 2025
Hotpoint

Hotpoint HCW607HT Manual

27 Februar 2025