GE JX2027DMBB Manual

GE Magnetron JX2027DMBB

Læs gratis den danske manual til GE JX2027DMBB (8 sider) i kategorien Magnetron. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 10 anmeldelser. Har du et spørgsmål om GE JX2027DMBB, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Built-In Trim Kits
Instructions JX2027 and JX2030
Read these instructions completely and carefully.
•IMPORTANT – Save these instructions for local inspector’s use.
•IMPORTANT – Observe all governing codes and ordinances.
•Note to Installer – Be sure to leave these instructions with the
Consumer.
•Note to Consumer – Keep these instructions for future reference.
•For easier installation and personal safety, we recommend that two people
install this microwave oven.
WARNING —This oven must be plugged into a properly
grounded 3-hole, 120V receptacle as required by the National Electrical Code
or the Canadian Electrical Code.
❒
BEFORE YOU BEGIN
• Do not alter or modify any part of this kit or the oven.
• Unplug the microwave oven before attempting installation of this kit.
• Skill level – Installation of this appliance requires basic mechanical and
electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
• This kit is UL/CSA listed for installation alone or over any GE/GE Profile
single electric wall oven. Not for use adjacent to (within 2 feet of) any gas
or electric range, cooktop or oven.
• This kit is for use on models: PEB2060DMBB, PEB2060DMWW,
PEB2060DMCC, PEB2060SMSS, JEB1860DMBB, JEB1860DMWW,
JEB1860DMCC, JEB1860SMSS, PEB206CDNBB, PEB206CSNSS,
PEB206CDNWW, JEB186CDNWW, JEB186CDNBB and JEB186CSNSS.
TOOLS YOU WILL NEED
❒ Phillips screwdriver
❒ Pencil
❒ Tape measure
❒ Awl or punch
❒ Drill with 7⁄64″bit or #35
FOR YOUR SAFETY:
WARNING – Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
❒ Level
❒ Scissors (optional)
1
PART QUANTITY
❒ Trim Frame 1
❒ Bottom Duct 1
❒ Side Duct 1
❒ 4 mm x 12 mm 23
Round-Head Screws (21 required
for installation)
❒ 4 mm x 14 mm 6
Flat-Head Screws
(4 required for
installation)
❒ Anti-Tip Brace 1
❒ Anti-Tip Bracket 1
❒ Upper Duct 1
❒ Top Bracket 1
❒ Bottom Bracket 1
❒ Templates 2
PARTS INCLUDED
NOTE: This kit has extra screws to prevent the technician from spending extra
time locating a replacement screw in case they lose one during installation.
Questions? In the U.S., call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com.
In Canada, call 1.800.561.3344 or Visit our Website at: GEAppliances.ca.
❒
CUTOUT DIMENSIONS
1
2
* Min. depth with receptacle outside cabinet 191⁄2″
Min. depth with receptacle inside cabinet 22″
120 volt-60 Hertz grounded power receptacle
Installation Instructions
Models 27″30″
Height 163⁄4″163⁄4″
Width 251⁄2″251⁄2″
Depth (min.)* 191⁄2″or 22″191⁄2″or 22″
WARNING — This trim kit uses air flow
from the top, bottom and sides of the trim frame.
Blocking the air flow can cause the microwave to
function improperly and may cause damage to
the microwave.
Allow a 1 clearance beyond the edge of the trim″
frame to provide proper air flow.
On 27″models, allow 11⁄8″at the top, 11⁄16″on the sides
and 11⁄4″at the bottom for overlap of the Trim Frame
over the edges of the cutout.
On 30″models, allow 11⁄8″at the top, 21⁄16″on the sides
and 11⁄4″at the bottom for overlap of the Trim Frame
over the edges of the cutout.
FOR INSTALLATION ABOVE A
BUILT-IN OVEN:
Microwave oven should be installed on a 3/8″plywood
base and supported by 2x4 or 1x2 equivalent runners
on all sides. Base must be capable of supporting a
minimum of 100 lbs (45.3 kg).
Draw a line on the cutout floor at the center of the
cutout, and extend the line 1/2 down the face of″
the cabinet.
Draw a line on the top front face of the cabinet
at the center of the cutout. The line should extend
1/2″up the face of the cabinet. This center line will
be used for mounting the top bracket (see step 7).
Fold or cut the front edge of the template, along the
front guide line. Place the template flush along the
front edge of the cutout floor, aligning the center line
of the template with the center line of the cutout
floor. Mark the center positions with an awl or center
punch for the anti-tip brace location as shown.
Drill two holes for the anti-tip brace.
Install the anti-tip brace onto the cutout floor using
two round-head screws.
B
C
D
E
D
D
Round-head
screws (2)
Anti-Tip Brace
❒
INSTALL THE ANTI-TIP BRACE
2
Depth
Height
11⁄4″Overlap
Width
11⁄8″Overlap
1″Clearance
beyond trim frame
(on all sides)
3″Min.
27″Models: 11⁄16″overlap
30″Models: 21
⁄16″overlap
A
DIMENSIONS:
A = 11⁄2″
B = 3″
C = 183⁄16″
D = 1/2″
Bottom of trim kit
must be minimum
of 36″from floor
1′= 0.3 m
1″= 2.5 cm

Produkt Specifikationer

Mærke: GE
Kategori: Magnetron
Model: JX2027DMBB

Har du brug for hjælp?

Hvis du har brug for hjælp til GE JX2027DMBB stil et spørgsmål nedenfor, og andre brugere vil svare dig


Magnetron GE Manualer

GE

GE GCST09U1 Manual

9 Januar 2025
GE

GE UVM9125STSS Manual

30 December 2025
GE

GE PVM9215DFWW Manual

29 December 2024
GE

GE Profile PVM9195DFCC Manual

29 December 2024
GE

GE JVM6175SFSS Manual

29 December 2024
GE

GE JX9152ELDS Manual

27 December 2024
GE

GE JX827BMTS Manual

27 December 2024
GE

GE Café CSA1201RSS Manual

15 December 2024
GE

GE JX7227BLTS Manual

8 December 2024
GE

GE JX1530SMSS Manual

8 December 2024

Magnetron Manualer

Nyeste Magnetron Manualer

Smeg

Smeg FMIA120B3 Manual

1 April 2025
Candy

Candy CMGA 30DBST Manual

29 Marts 2025
Candy

Candy CAMW25X Manual

29 Marts 2025
Hisense

Hisense H25MOBS7HUK Manual

29 Marts 2025
Toshiba

Toshiba MWP-MM20P(WH) Manual

27 Marts 2025
Whirlpool

Whirlpool WMN461BXF Manual

4 Marts 2025
LG

LG MSER1130B Manual

3 Marts 2025
Hotpoint

Hotpoint HCW6O7HTS Manual

27 Februar 2025
Hotpoint

Hotpoint HCW607HT Manual

27 Februar 2025
Hotpoint

Hotpoint HMD44MXUK Manual

27 Februar 2025