GE JXS77BB Manual

GE Ovn JXS77BB

Læs gratis den danske manual til GE JXS77BB (2 sider) i kategorien Ovn. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 6 anmeldelser. Har du et spørgsmål om GE JXS77BB, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Installation Instructions
Body Side Kit For End of the Counter Installation
Tools Required:
#2 Phillips screw driver
Installing the Kit
This Body Side Kit must be installed prior to installing the Range in position.
Locate the body side keyway holes over the heads of the panel supports.
A
A1 Place the three panel supports in the 3 square holes of the vertical side trim and rotate 45° as shown below.
( May require Pliers) See illustration on back page.
A3 Insert 1” screw through shoulder rivet. Place the 1/2” spacer over the end of the 1” screw. Place the spacer-
shoulder rivet-screw assembly through washer. Install assembly in place of the screw removed in A2. (See
illustration on back page.)
A4
Pub. No. 31-10451
229C4053P434
Push the body side forward locking the slots of the keyway holes on the side panel supports.
A5
Place the longest screw (1-1/2” ) through the top hole of the body side at the rear of the range. Slide the spacer
(1-1/4”) over the screw and attach the screw to the hole in the rear of the range above the louvers. Do not tighten.(If
a backsplash kit is used in conjunction with this kit, use the shorter spacer found in the backsplash kit.) See
illustration on back page.
A6
Lift the rear of the body side to close the gap between the cooktop glass and the body side. Tighten the screws
from steps A6 and A7.
A7
Place the short (3/8” long) hex head screw through the bottom hole in the rear of the body side and attach to the
lower section of the range. See illustration on back page, Do Not Tighten.
A8
To stabilize the bottom front corner of the body side-range assembly, place the clip over the inside flange of the
body side and the outside flange of the vertical side trim, as shown in illustration. Start by raising the front corner
of the range by turning the leveling leg downward, to provide more clearance for attaching clip. See illustration on
back page for details of attaching clip. (Hold the body side and the vertical side trim close for easier assembly
of the clip.) See Illustration on back page.
A9
Refer to the Installation Instructions included with the range to place the range into kitchen location.
A10
1/4” Nut Driver
Pliers
Parts Supplied:
3 Panel Supports
1 Body Side
1/2” Spacer
1-1/4” Spacer
Clip
Shoulder Rivet
Washer
#8-3/8” Long
Hex Screw
#8-1” Long Screw
#8-1-1/2” Long Screw
Use these instructions to mount the Body Side Kit on either side of the Slide-In Range.
Remove the hex head screw at the top end of the vertical side trim as shown in the illustration on back page.
A2
1
2
BASE
ASSY.
VERTICAL
SIDE TRIM
3/8" LONG
HEX HEAD
SCREW
BODY
SIDE
1-1/2" LONG
SCREW
UPPER REAR
CORNER
BODY SIDE
1 1/4" LONG
SPACER
PUSH
CLIP
CLIP JOINS BODY SIDE
CLIP JOINS BODY SIDE
CLIP JOINS BODY SIDE
CLIP JOINS BODY SIDE
TO RANGE SIDE TRIM
TO RANGE SIDE TRIM
TO RANGE SIDE TRIM
TO RANGE SIDE TRIM
CLIP JOINS BODY SIDE
TO VERTICAL SIDE TRIM
INNER FLANGE
INNER FLANGE
INNER FLANGE
INNER FLANGE
BODY SIDE
BODY SIDE
BODY SIDE
BODY SIDE
INNER FLANGE
BODY SIDE
TURN PANEL
SUPPORT 45˚
WASHER
1" LONG SCREW
1/2" SPACER
REMOVE THE (UPPER)
HEX HEAD SCREW
LOCATED INSIDE THE
BODYSIDE TRIM
OUTER FLANGE
OUTER FLANGE
OUTER FLANGE
OUTER FLANGE
VERTICAL SIDE TRIM
VERTICAL SIDE TRIM
VERTICAL SIDE TRIM
VERTICAL SIDE TRIM
OUTER FLANGE
VERTICAL SIDE TRIM
SHOULDER RIVET
PUSH CLIP HOLDS BO
PUSH CLIP HOLDS BO
PUSH CLIP HOLDS BO
PUSH CLIP HOLDS BOTH
TH
TH
TH
THE VERTICAL
THE VERTICAL
THE VERTICAL
THE VERTICAL SIDE TRIM
SIDE TRIM
SIDE TRIM
SIDE TRIM
AND
AND
AND
AND THE BOD
THE BOD
THE BOD
THE BODY SIDE A
Y SIDE A
Y SIDE A
Y SIDE AT
T
T
T
THE LO
THE LO
THE LO
THE LOWER FRONT CORNER
WER FRONT CORNER
WER FRONT CORNER
WER FRONT CORNER
PUSH CLIP HOLDS BOTH
THE VERTICAL SIDE TRIM
AND THE BODY SIDE AT
THE LOWER FRONT CORNER
BODY
SIDE
TRIM
BODY
SIDE
A2
A3
A9
A1
A7
A6
A4 A5

Produkt Specifikationer

Mærke: GE
Kategori: Ovn
Model: JXS77BB

Har du brug for hjælp?

Hvis du har brug for hjælp til GE JXS77BB stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ovn GE Manualer

GE

GE Profile P9SBCAS6WBB Manual

10 September 2025
GE

GE JKS5000DVBB Manual

7 August 2025
GE

GE JKS5000SVSS Manual

7 August 2025
GE

GE JTD5000DVBB Manual

7 August 2025
GE

GE JTD5000EVES Manual

7 August 2025
GE

GE JKD5000SVSS Manual

7 August 2025
GE

GE JTS5000EVES Manual

6 August 2025
GE

GE JTD5000SVSS Manual

6 August 2025
GE

GE JKD5000DVBB Manual

6 August 2025
GE

GE JTS5000SVSS Manual

6 August 2025

Ovn Manualer

Nyeste Ovn Manualer

AEG

AEG BBP6052B Manual

13 September 2025
Grunkel

Grunkel HR-23 Manual

13 September 2025
Signature

Signature FC46-BL Manual

13 September 2025
Brandt

Brandt FC55MUW Manual

12 September 2025
Brandt

Brandt BFP7554W Manual

12 September 2025
Brandt

Brandt FC609MUB Manual

12 September 2025
Schneider

Schneider SCEO2345CTB Manual

12 September 2025
Neff

Neff XED342 Manual

12 September 2025
Zanussi

Zanussi ZPCNA7XN Manual

12 September 2025
Whirlpool

Whirlpool AKP9 785 IX Manual

12 September 2025