GE ZV881WSS Manual

GE Emhætte ZV881WSS

Læs gratis den danske manual til GE ZV881WSS (16 sider) i kategorien Emhætte. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 13 anmeldelser. Har du et spørgsmål om GE ZV881WSS, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/16
Monogram.
We bring good things to life.
®
If you have questions, call 800-GE-CARES or visit our website at: www.monogram.com
Installation
Instructions
30", 36" and 48"
Proessional Vent Hoods
48" Wide Models:
ZV881, ZV891, ZV880, ZV890
36" Wide Models:
ZV671, ZV681, ZV670, ZV680
30" Wide Models:
ZV370, ZV371
Installation Preparation
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have any questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power off
at the service panel and lock service panel to prevent
power from being switched on accidentally. If the
service panel cannot be locked, fasten a tag or
prominent warning label to the panel.
For general ventilating use only. Do not use to
exhaust hazardous or explosive materials or vapors.
Structural framing, installation work and electrical
wiring must be done by qualified person(s).
In accordance with all applicable codes and standards
including fire-rated construction.
Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guideline and safety standards such as those pub-
lished by the National Fire Protection Association
(NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
Local codes vary. Installation electrical connections
and grounding must comply with applicable codes.
In the absence of local codes, the vent should be
installed in accordance with National Electrical Code
ANSI/NFPA 70-1990 or latest edition.
TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
2
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - Save these instructions for
local inspector’s use.
• IMPORTANT - Observe all governing
codes and ordinances.
• Note to Installer - Be sure to leave these instruc-
tions with the Consumer.
• Note to Consumer - Keep these instructions with
your Owner’s Manual for future reference.
• – Installation of this appliance requiresSkill Level
basic mechanical and electrical skills.
• Completion time – 1 to 3 hours.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
For Monogram local service in your area,
1-800-444-1845.
For Monogram service in Canada, call
1-888-880-3030.
For Monogram Parts and Accessories, call
1-800-626-2002.
CAUTION:
Due to the weight and size of these vent hoods and to
reduce the risk of personal injury or damage to the
product, TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
WARNING:
To reduce the risk of fire or electrical shock, do not
use this range hood with any external solid-state speed
control device. Any such alteration from original
factory wiring could result in damage to the unit and/
or create an electrical safety hazard.
CONTENTS
Installation Preparation
Models, Duct Covers, Ductwork Accessories................... 3
Product Dimensions, Product Clearances ...................... 4
Advance Planning ............................................................. 5
Power Supply ................................................................... 5
Duct Fittings ...................................................................... 6
Installation Instructions
Tools and Materials Required .......................................... 7
Step 1, Remove Packaging ............................................... 7
Step 2, Check Installation Hardware............................... 7
Step 3, Determine Accessories, Ductwork and Wiring
Locations .............................................................. 8
Step 4, Recommended Wall Mounting Method
Wall Framing For Hood Support ........................ 9
Step 5, Install Hood Onto Wall...................................... 10
Step 6, Alternate Soffit Mounting Method
Soffit Framing .................................................. 11
Step 7, Connect Electrical .............................................. 12
Step 8, Connect Ductwork ............................................. 12
Step 9, Reassemble Hood............................................... 12
Step 10, Install Duct Cover ............................................ 13
Step 11, Install Filters ..................................................... 13

Produkt Specifikationer

Mærke: GE
Kategori: Emhætte
Model: ZV881WSS

Har du brug for hjælp?

Hvis du har brug for hjælp til GE ZV881WSS stil et spørgsmål nedenfor, og andre brugere vil svare dig


Emhætte GE Manualer

GE

GE JV565HBB Profile Manual

31 Maj 2025
GE

GE JV665HWW Profile Manual

31 Maj 2025
GE

GE JV666HSS Profile Manual

31 Maj 2025
GE

GE JV635HWW Profile Manual

29 Maj 2025
GE

GE UVC9480SLSS Manual

30 December 2025
GE

GE JV665HBB Profile Manual

15 December 2024
GE

GE UVC9420SLSS Manual

7 December 2024
GE

GE JV337XAD Manual

19 September 2024
GE

GE UVD6301DPBB Manual

1 September 2024
GE

GE UVD6361DPBB Manual

1 September 2024

Emhætte Manualer

Nyeste Emhætte Manualer

Comfee

Comfee CHW 7.6M77A3 Manual

17 Juni 2025
Smeg

Smeg KPRU24X Manual

17 Juni 2025
Smeg

Smeg KBTU48X Manual

17 Juni 2025
Smeg

Smeg KPRU36X Manual

17 Juni 2025
AEG

AEG NDE562DB Manual

17 Juni 2025
ElectriQ

ElectriQ eiQTMVISOR Manual

17 Juni 2025
Comfee

Comfee CHT 3.6B Manual

17 Juni 2025
ElectriQ

ElectriQ eiQ90CANGBL Manual

17 Juni 2025
Comfee

Comfee CHK 3.6.6J64A1B Manual

17 Juni 2025
ElectriQ

ElectriQ eiQ52CANGBL Manual

17 Juni 2025