Genelec 8030 CP Manual


Læs gratis den danske manual til Genelec 8030 CP (32 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Genelec 8030 CP, eller vil du spørge andre brugere om produktet?

Side 1/32
8030B
Operating Manual 2-7
Betriebsanleitung 8-13
Manuel d’utilisation 14-19
yttöohje 20-25
Bruksanvisning 26-31
2 English
General description
The bi-amplified GENELEC 8030B is a two way
active monitoring loudspeaker designed to be small
but still have high output, low coloration, and broad
bandwidth.
The 8030B is ideal for near field monitoring,
mobile vans, broadcast and TV control rooms, sur-
round sound systems, home studios, multimedia
applications and also for use with computer sound-
cards. As an active loudspeaker, it contains driv-
ers, power amplifiers, active crossover filters and
protection circuitry. The MDE™ (Minimum Diffrac-
tion Enclosure™) loudspeaker enclosure is made
of die-cast aluminium and shaped to reduce edge
diffraction. Combined with the advanced Direc-
tivity Control WaveguideTM (DCWTM), this design
provides excellent frequency balance in difcult
acoustic environments. If necessary, the bass
response of the 8030Bs can be extended with a
suitable Genelec subwoofer.
Positioning the loudspeaker
Each 8030B monitor is supplied with an inte-
grated amplifier unit, mains cable and an operating
manual. After unpacking, place the loudspeaker in
its required listening position, taking note of the line
of the acoustic axis. The axes of all loudspeakers
should converge at ear height at the listening position
(see Figure 1).
Connections
Before connecting up, ensure that the mains
switch is off and the volume control fully counter-
clockwise. These controls are located on the front
panel of the loudspeaker. Do not connect the loud-
speaker to an unearthed mains supply or using an
unearthed mains cable.
Audio input is via a 10 kOhm balanced female
XLR connector labelled “INPUT. An unbalanced
source may be used as long as pin 3 is grounded
to pin 1 at the unbalanced source connector (see
Figure 2).
The male XLR “OUTPUT connector can be
used for daisy-chaining up to six 8030B’s together
or for connecting a Genelec 7050B subwoofer. The
volume control attenuates the signal on this output,
so the first “master” loudspeaker on a daisy-chain
can be used to adjust the level on the whole chain.
The volume controls on the “slave” loudspeakers
should be set fully clockwise.
Once the connections have been made, the
loudspeakers are ready to be switched on.
ISSTM autostart function
When the power switch on the front panel of the
loudspeaker is set to ON”, the Intelligent Signal
SensingTM
(ISSTM) autostart function of the 8030B is
active. Automatic powering down to standby mode
happens after a certain time when playback has
ended. The power consumption in standby mode is
typically less than 0.5 watts. The playback will auto-
matically resume once an input signal is detected
from the source.
There is a slight delay in the automatic power-
ing up. If this is undesirable, the ISS
TM function can
be disabled by setting the “ISS DISABLE” switch
8030B
Active Monitoring System


Produkt Specifikationer

Mærke: Genelec
Kategori: Højttaler
Model: 8030 CP

Har du brug for hjælp?

Hvis du har brug for hjælp til Genelec 8030 CP stil et spørgsmål nedenfor, og andre brugere vil svare dig




Højttaler Genelec Manualer

Genelec

Genelec 8381A Manual

15 November 2024
Genelec

Genelec 8010 APM Manual

30 September 2024
Genelec

Genelec 8020D Manual

27 September 2024
Genelec

Genelec 8020B Manual

9 September 2024
Genelec

Genelec 3440A Manual

5 September 2024
Genelec

Genelec 8010 AW Manual

10 August 2024
Genelec

Genelec 8040A Manual

9 August 2024
Genelec

Genelec 8050B Manual

8 August 2024
Genelec

Genelec 8050A Manual

4 August 2024
Genelec

Genelec 8320AWM Manual

4 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer