Grundfos KPL.1800.700.16.T.50.17.L.40 Manual

Grundfos Vandpumpe KPL.1800.700.16.T.50.17.L.40

Læs gratis den danske manual til Grundfos KPL.1800.700.16.T.50.17.L.40 (8 sider) i kategorien Vandpumpe. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Grundfos KPL.1800.700.16.T.50.17.L.40, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
r e v i s i o n 0.0
GU02 Manual
750-18, Jangnok-Dong, Gwangsan-Gu
Gwangju, Korea
Tel: 82-62-602-8400 (Rep.)
Monitoring Unit – GU02
Prepared by.
Rev. No. Rev1.0
Date. 12-Nov-13
Page. 2 / 7
1. General
GU02 is complete monitoring unit, it can monitor the pump status by detecting motor overheating, high bearing
temperature, seal leakage and moisture in junction box and if there is any problem you can recognize it by alarm
sound.
GU02 can detect
1) Moisture incursion into the junction box
2) Overheat of stator windings (U,V,W)
3) High temperature of bearing (Upper and Lower)
4) Seal leakage
GU02 can be mounted in MCC (motor control center) without the need for a power transformer since it has an
inbuilt voltage regulating device.
2. Sensors inside the Motor
The installed sensors are as following;
1) Thermal Protectors in Stator Windings
- For 90 kW(120 Hp) and above, three PT 100 ohm type thermal protection sensors are embedded in each
phase of stator windings to monitor the stator winding temperature.
- The three thermal protect devices can be connected in parallel (6 wires to connect to GU02) or in series (2
wires to connect).
- The setting temperature of GU02 can be adjusted easily without service technician; the recommended
temperature setting is 125 degrees C.
- For the 75kW (100Hp) and below motors, one bimetal type thermal protection sensor is installed in stator
winding and the inherent setting temperature of the bimetal is 125degree C.
- If three bimetal type sensors are required these can be installed as an option. It will be connected in series
so 2 wires will be connected to the GU02.
2) Leakage Sensor
- One electrode type seal leakage sensor is installed on the seal chamber.
- If the primary seal leaks and water penetrates into the oil chamber, the resistance of the
electrode changes to below 5 Kilo ohm.
- Under normal conditions, the resistance value of the electrode sensor is greater than
10 mega ohm.

Produkt Specifikationer

Mærke: Grundfos
Kategori: Vandpumpe
Model: KPL.1800.700.16.T.50.17.L.40

Har du brug for hjælp?

Hvis du har brug for hjælp til Grundfos KPL.1800.700.16.T.50.17.L.40 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Vandpumpe Grundfos Manualer

Grundfos

Grundfos KPL.1800.700.16.T.50.19.L.38 Manual

20 Juni 2025
Grundfos

Grundfos APG.50.65.3 Manual

20 Juni 2025
Grundfos

Grundfos KWM.1600.650.14.T.50.1135.M.38 Manual

20 Juni 2025
Grundfos

Grundfos KPL.1800.700.16.T.50.17.L.40 Manual

20 Juni 2025

Vandpumpe Manualer

Nyeste Vandpumpe Manualer

Davey

Davey SpaPower Spa Control SP601 Manual

17 Juni 2025
Little Giant

Little Giant 16EH-514540 Manual

17 Juni 2025
Little Giant

Little Giant 10SC-CIA-SFS Manual

17 Juni 2025
Zodiac

Zodiac EXO IQ Mid Manual

17 Juni 2025
Little Giant

Little Giant 9EN-CIM Manual

17 Juni 2025
Little Giant

Little Giant Pit+Plus Jr Manual

17 Juni 2025
Little Giant

Little Giant HT-6E-CIA-FS Manual

17 Juni 2025
Little Giant

Little Giant 20E-CIM Manual

16 Juni 2025
Milwaukee

Milwaukee M18 BLSWP Manual

16 Juni 2025
Little Giant

Little Giant 5-MSP Manual

16 Juni 2025