Setting the shutter position for scenes
If the radio shutter button is assigned to a scene
as a receiver, then the shutter position can be set
for this scene.
Move the shutter to the top nal position and
wait for two minutes.
Move the shutter downwards to the desired
position.
Set the desired slat position by pressing the
button briey several times (max. 30 UP steps).
Keep transmitter button belonging to the con-
gured scene command pressed for more than
5 seconds.
The shutter moves up for a second and then
down for a second. The scene position has
been saved.
Locking/unlocking scene changes
To prevent unwanted changes to a scene, the
changing of the scene can be locked.
Start conguration.
Select transmitter button: Select the button for
the scene command.
Select function on receiver: When the function
Scene 1 Scene 2 fct or is indicated by the LED
blinking in green colour, keep the button on fct
the receiver pressed for more than 5 seconds
until the cfg LED blinks briey.
Then the -fct LED indicates the currently con
gured status:
1 x blinking: Possible to change and save
scene.
2 x blinking: Changing the scene is locked.
Press button and select the desired setting.fct
The setting changes each time the button is
pressed.
To accept the selected setting time, keep the
fct button pressed for more than 2 seconds.
Finish conguration: Short press on button cfg
on the transmitter.
Radio conguration - quicklink
The radio con guration sets the functional con-
nection between commanding (transmitters) and
function-executing (receivers) radio components.
Thus wireless e.g. central unit, group unit, extensi-
on unit and time controls can be realised.
The following can be congured:
- The local operation of the load connected to
the insert
- Radio commands to control other receivers
- Functions that are executed when radio com-
mands are received
Local operation is a function that is pre-con
gured at the factory and can be changed.
As an example, the con guration of a wall
transmitter and the radio shutter push-button as
receiver is described below.
The design cover of the radio shutter push-button
is not attached.
Conguration of radio shutter push-button as
a transmitter
If the radio shutter push-button is operated as a
transmitter, it can support the followingfunctions
for the receivers:
UP/DOWN (switch)
As an example, the con guration of the radio
shutter push-button with receivers for whichthe
supported displays occur through the cfg LED and
fct LED is described here. Different conguration
displays, such as for receivers with display, are to
be taken from the receiver operating instructions.
Deleting a conguration
To delete a congured receiver or the local opera-
tion, execute the con guration again.
Start conguration (see conguration of radio
button as a receiver).
If necessary Select transmitter button.
Select function on receiver: Select the function
Delete on the receiver and conrm function on
the receiver.
Finish conguration: Short press on cfg button
on the transmitter.
Conguring group functions
By means of a group function, one transmitter
controls several receivers. To do so, the same
function must be congured on all receivers.
Start conguration (see conguration of radio
button as a receiver).
If necessary . Select transmitter button
Select function on receiver: Select the group
function as described above on each receiver
to be integrated and conrm function on the
receiver.
Finish conguration: Short press on button cfg
on the transmitter.
Conguration of scenes
Individual settings for lighting and the position
of shutters can be combined into scenes. Two
different scenes can be created via quicklink and
called up by pressing a button on the transmitter. A
scene is created by conguring a push-button ope-
ration area of a transmitter (radio command) in the
corresponding receivers with the scene function
(see Table 5: Congure the function for the radio
blind button).
Start conguration
Select transmitter button: Select the button for
the scene command.
Select function on receiver: Select the scene
function as described above on each receiver
to be integrated and conrm function on the
receiver.
Finish conguration: Short press on button cfg
on the transmitter.
Changing/saving scenes
Switching, dimming and blind statuses of the
receivers in a scene can be changed and saved.
The load status can be congured locally or by
remote control on the receivers integrated into
the scene, e.g. light 1 = 60 % brightness level,
light 2 = 40 % brightness level, blind down.
Keep transmitter button belonging to the con-
gured scene command pressed for more than5
seconds.
A brief status changeover of the receiver si-
gnals the successful saving of the scene.
Step Result
Start conguration
Short press on button on the wall trans-cfg
mitter.
If there is no further activation, the congura-
tion is automatically ended after 10 minutes.
The LEDs on the wall transmitter and the radio cfg
button light up in red colour.
All receivers within radio range also indicate the
conguration mode. .
Select transmitter button
Short press on press-activation point on the
wall transmitter which should activate the Up
function.
The LED on the wall transmitter blinks for 1 se-cfg
cond.
If it has already been congured, the fct LED of the
radio blind button indicates the currently con gured
function.
Select function on receiver
Repeated short press on button on the ra-fct
dio blind button until the desired UP-function
is displayed (Table 4).
After each activation, the LED indicates the func-fct
tion.
If the transmitter button has already been con gu-
red with a function in a different receiver and/or the
con gured function is part of a group control, only
this function can be con gured. To change a func-
tion, the existing con guration must be deleted
and the new one needs to be con gured.
Conrming function on receiver
To conrm, keep the fct button pressed for
more than than 2 seconds.
> 2 s
The LED blinks during the saving process (approx. cfg
5 s). The fct LED con rms the function selection by
displaying the corresponding colour.
Rapid blinking of the LED indicates an impos-cfg
sible combination or an error.
Finish conguration
Short press on button on the wall trans-cfg
mitter again.
The LEDs on the wall transmitter, the radio blindcfg
button and all receivers within radio range go out. The
function is congured.
If required, con gure the Down function in the
same way.
Table 5: Conguration of the function for the radio shutter push-button
fct LED
display
Congurable
function
Function resulting from transmitter operation,
notes
Move UP,
stop
Short press on button: adjustment of the slat position / stop
Long press on button: lock, shutter moves to top nal position.
DOWN,
stop
Short press on button: adjustment of the slat position / stop
Long press on button: lock, shutter moves to bottom nal position.
1 Scene 1 Receiver is allocated to a scene due to the con guration of the
function.
Short press on push-button: calling up the saved state of the con-
nected load for the scene
2 Scene 2
Shutter switch Radio shutter switch is assigned to a compatible transmitter. Up/
down function is assigned to one con guration operation.
UP forced
mode Moves the shutter to the appropriate nal position with higher-level
priority. The execution of other commands is only possible when
forced operation is reset.
DOWN forced
mode
Memory
function
Activates/deactivates execution of the memory function (see Memory
function). Recording cannot be activated by radio command.
Delete. No function
Assignment to transmitter is deleted
Table 4: Congurable receiver functions
Resetting to factory settings
By factory default, the button is precongured for
the operation of a shutter insert (see Operation).
Press the button for more than 10 seconds.cfg
The LED blinks red. If the system is reset cfg
to the factory setting, the LED goes out again.
Reconguration can only commence 15 se-
conds after the device is reset or switched on.
Appendix
Technical data
Radio frequency 868 MHz
Radio protocol KNX radio
Connection Mounting on suitable inserts (see
Accessories)
Power supply via insert
quicklink logic functions max. 20 transmitters/
receivers
Receiver category 2
Transmitter duty cycle < 1%
Change-over time min. 600 ms
Blind operating time 2 min
Jog mode/slat adjustment time 250 ms
Relative humidity 0 ... 65 % (no condensation)
Ambient temperature -5 … +45 °C
Storage/transport temperature -25 … +70 °C
Accessories
Shutter insert Comfort 8522 11 0..
Power supply
for radio application module 8502 01 0..
Radio brightness sensor 8580 11 00
Warranty
We reserve the right to make technical and formal
changes to the product in the interest of technical
progress.
Our products are under guarantee within the
scope of the statutory provisions.
If you have a warranty claim, please contact the
point of sale or ship the device postage free with a
description of the fault to the appropriate regional
representative.
Step Result
Start conguration
Short press on button on the radio shutter but-cfg
ton.
If there is no operation, conguration is automati-
cally ended after 10 minutes.
The LEDs on the radio shutter button and cfg
the receivers within radio range light up in red
colour. On the LED of the radio shuter button, fct
the current local operation is also shown (factory
setting Up/Down switch, LED red/green).fct
5 78321 4 6
L N
S1
fct
cfg
