Hager 85346131 Manual

Hager Ikke kategoriseret 85346131

Læs gratis den danske manual til Hager 85346131 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Hager 85346131, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

KNX radio motion detector comfort

1.1 m quicklink

Order no. 8534 51 ..

KNX radio motion detector comfort

2.2 m quicklink

Order no. 8534 61 ..

Configuration instructions

Berker GmbH & Co. KG

Zum Gunterstal

66440 Blieskastel, Germany

Tel.: + 49 6842 945 0

Fax: + 49 6842 945 4625

e-mail: info@berker.de

www.berker.com

04/2022

6LE007947A

KNX radio conﬁ guration

quicklink

The radio conﬁ guration sets up the functional

connection between commanding (transmitters)

and function-executing (receivers) radio compo-

nents. Thus, central, group, extension unit and

time controls, for example, can be implemented in

a wireless manner.

The following can be conﬁ gured:

-The local operation of the load connected to the

insert

- Radio commands to control other receivers

- Functions which are executed when the radio

commands are received

►See Table 5

For conﬁ guration by means of Hager connec-

tion device TX100 or ETS, additional functions

are available (see operating instructions for

TX100 or application description for ETS).

Conﬁ guration to control the load connected to the

insert via reception of a radio command.

As an example, the conﬁ guration of a wall-trans-

mitter and a radio motion detector as receiver is

described (Table 6).

fct LED

display

Conﬁ gurable

functions

Function resulting from transmitter operation,

notes

On switch insert

On dimmer insert

ON/OFF 1)

ON/OFF,

dim UP/

DOWN

Short button-press: Switch ON/OFF

Long button-press: Dimming, reverse dimming direc-

tion per actuation

ON,

dim UP

Short button-press: Switch ON

Long button-press: Dim UP to maximum brightness

OFF

OFF,

dim

DOWN

Short button-press: Switch OFF

Long button-press: Dim DOWN to minimum bright-

ness

Scene 1

Receiver is allocated to a scene due to the conﬁ gura-

tion of the function.

Short button-press: Short button-press: Recall the

saved state of the connected load for the scene

Scene 2

Timer

Switch ON for the set switch-on time

Factory setting = 3 min

ON/OFF

(switch/push-button)

Closing of the activating contact switches the load

ON, opening of the contact switches the load OFF.

Forced mode ON

Switches the load with higher priority to the appropri-

ate state. Execution of other commands is only possi-

ble after resetting the forced command.

Forced mode OFF

Presence

simulation 1)

Activates/deactivates execution of presence simula-

tion (See Activating/deactivating presence simulation).

Master-Slave

Is used to extend the detection area. Receives

switch-on commands in case of motion detection in

the detection area of the transmitter (Slave). Switches

the lighting ON for the set delay time.

The brightness evaluation only takes place on the

master, the slave only detects motion.

Can only be conﬁ gured between radio motion

detectors.

Cancel

No function

Assignment to transmitter is deleted

Execution of the receiver function and local motion detector function have the same priority:

–If the transmitter was ﬁ rst switched on/oﬀ and then motion was detected afterwards, then the motion detector will

override the transmitter command

–If motion was detected and thereafter, during the delay time, the system is switched on/oﬀ via the transmitter, then

the transmitter will override the motion detector

Only with KNX radio motion detector on power supply for KNX radio application module as transmitter

Table 5: Conﬁ gurable functions

Operation

Result

Start conﬁ guration



Press the button on the wall-transmitter cfg

brieﬂ y.

If there is no further activation, the

conﬁ guration is automatically ended after 10

minutes.

The LEDs on the wall-transmitter and the radio cfg

motion detector light up in red colour.

150

90°

...

45° 45°

...

90°

fct

cfg

All the receivers within radio range also display the

conﬁ guration mode.

Select transmitter button



Brieﬂ y press the press-activation point on the

wall-transmitter, which should activate the

function.

The cfg LED on the wall-transmitter ﬂ ashes for 1

second.

If conﬁ gured already fct LED of the motion detector

indicates the currently conﬁ gured function.

Select function on receiver



Repeatedly apply short presses to the fct

button on the motion detector until the desired

function is displayed (Table 5).

150

90° 45° 90° ...

fct

cfg

After each operation, the fct LED indicates the

function.

If the transmitter button has already been

conﬁ gured with a function in a diﬀ erent receiver

and/or the conﬁ gured function is part of a group

control, only this function can be conﬁ gured.

To change a function, the existing conﬁ guration

must be deleted and the new one needs to be

conﬁ gured.

Conﬁ rm function on receiver



To conﬁ rm, keep the button pressed for fct

more than 2 seconds.

150

90° 45° 90° ...

fct

cfg

> 2 s

The cfg LED ﬂ ashes during the saving process

(approx. 5 s). The LED conﬁ rms the function fct

selection by displaying the corresponding colour.

150

90° 45° 45° 90° ... ...

fct

cfg

Rapid ﬂ ashing of the cfg LED indicates a

combination that is not possible or an error.

Completing the conﬁ guration



Brieﬂ y press the cfg button on the wall-

transmitter again.

The LEDs on the wall-transmitter, on the motion cfg

detector and on all receivers within radio range go

out. The function is conﬁ gured.

Table 6: Conﬁ guration of the function for the KNX radio motion detector

Conﬁ guration of KNX radio motion detector as a receiver

Produkt Specifikationer

Mærke:	Hager
Kategori:	Ikke kategoriseret
Model:	85346131

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager 85346131 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Hager Manualer

Hager WXF228 Manual

10 August 2025

Hager UKM340480 Manual

10 August 2025

Hager TRC301B Manual

10 August 2025

Hager GS20109011 Manual

10 August 2025

Hager AKB42000402 Manual

10 August 2025

Hager WXT312 Manual

10 August 2025

Hager BKSAN065110 Manual

10 August 2025

Hager VR10127011 Manual

10 August 2025

Hager UKM240280 Manual

10 August 2025

Hager ESR3336029 Manual

10 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Dahua Technology DHL32-F600 Manual

28 Oktober 2025

Dahua Technology VTS5240B Manual

28 Oktober 2025

Dahua Technology HAC-HFW1230S-POC Manual

28 Oktober 2025

Dahua Technology HAC-HDW1400TLMQ-A Manual

28 Oktober 2025

Dahua Technology EVS7124D Manual

27 Oktober 2025

Dahua Technology XVR7816S-4KL-X-LP Manual

27 Oktober 2025

Dahua Technology HAC-HDW1220EM Manual

27 Oktober 2025

Dahua Technology ISC-M6550 Manual

27 Oktober 2025

Dahua Technology EVS7148D Manual

27 Oktober 2025

Dahua Technology HAC-HFW2249E-A Manual

27 Oktober 2025