Hager 85745139 Manual

Hager Ikke kategoriseret 85745139

Læs nedenfor 📖 manual på dansk for Hager 85745139 (3 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 12 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/3

KNX Radio shutter timer quicklink

Safety instructions

Electrical equipment must only be installed

and assembled by a qualied electrician in ac-

cordance with the relevant installation stan-

dards, regulations, directives and safety and

accident prevention directives of the country.

Failure to comply with these installation in-

structions may result in damage to the device,

re or other hazards.

The radio transmission is not suitable for safe-

ty or alarm applications.

These instructions are an integral component

of the product, and must be retained by the

end user.

Design of the device

(3)

(5)

(6) (7)

(4)

(2)

(1)

Figure 1: Design of the device

(1) Insert (see „Accessories“, not in scope of

delivery)

(2) Frame (not in scope of delivery)

(3) Application module

(4) Display

(5) Design cover

(6) Screw for dismantling protection (not for

design lines R.1/R.3)

(7) Operation buttons

Function

This device is a product of the quicklink system, in

which installation devices communicate via radio

signals.

quicklink stands for a conguration mode in which

the function-related connection between trans-

mitters and receivers is set on the device through

push-buttons and displays without further tools.

All devices congurable by quicklink can be opera-

ted together in one system.

This device is compliant to the R&TTE-Directive

1999/5/EG. The Declaration of Conformity and

further system information can be found on our

homepage www.berker.de.

The device may be used in all EU and EFTA

countries.

Correct use

- Application module for shutter inserts or power

supply for radio application modules

- Manual, time-controlled and automatic operati-

on of blind/shutter motors connected to insert

- Transmission and reception of manual, time-

controlled and automatic operation commands

via quicklink

- Unsuitable for lighting control

- Only suitable for use in indoor areas, no drip or

spray water

The quicklink conguration of the devices must

only be carried out by qualied electricians.

Product characteristics

- quicklink functions for integration into the remo-

te and group control of blinds/shutters

- Integration into scenes

- Two preset standard time programmes, indivi-

dually adjustable

- Astro programme for automatic operation at

dawn/dusk

- Astro time shift to adjust the operation times

- Holiday programme for random operation times

in automatic mode

- Party programme to prevent unintentional ope-

ration of the shutters by automated operation

commands as well as radio/extension unit com-

mands

- Keylock

- Automatic switching to standard/daylight saving

time

- Brightness-dependent operation when using a

radio sun sensor

Performance after mains breakdown/return of

mains supply

- Mains breakdown:

Saving of the current conguration and pro-

gramming in the non-volatile memory. The de-

vice then switches to economy mode. Only the

internal clock continues to run to keep the time

up-to-date. The use of a bu󰀨er memory en-

sures that the time stays up-to-date for up to 24

hours.

- Return of mains supply:

The application module executes an initialisati-

on operation1), the basic display is restored.

The stored conguration and programming is

loaded from the memory. Any operations pen-

ding when the power supply broke down will

not be executed after return of mains supply.

1) If the bu󰀨er memory is full, date and time must be

entered again.

Operation

Operating concept and display elements

When controlling the shutter, the buttons (Fig. 2)

distinguish between a short press and a long press

of > 0.5 seconds on the button.

Pressing the button for > 2 seconds can trigger

various functions within the menu operation.

The current clock status is shown in the display.

Active functions are displayed by using symbols

(Table 1). Display illumination is activated for as

soon as a button is pressed.







07 3:0

Wednesday

12 4:1

21 2:0

(8) (9) (11)(10)

(12)

(13)

(14)

Figure 2: Display and operating elements

(8) UP button p

(9) Back button á

(10) OK button

(11) DOWN button q

(12) Display area for weekday and time

(13) Display area for active functions/programming

(14) Display area for the next operation times

Symbol Function

Keylock active

Manual operation,

no automatic operation times

Preset programme (week programP1 -

me) or (week/weekend program-P2

me) is active

Astro programme is active,

UP and DOWN operation times are

controlled depending on dawn/dusk

times

Party programme is active,

manual operation only. Programmes,

extension units and radio commands

are not executed

Normal radio operation is active,

radio commands for master or group

controls can be transmitted and re-

ceived

Standalone programme,

Device has temporarily been removed

from higher-level master controls, but

can still be active in a group control

Holiday programme,

Random variation of operation times,

only possible in combination with

, ,

Device is in radio conguration mode

Table 1: Symbols in the function/programme line

(13) of the display

Operate shutter - operation from the basic

display

Manual shutter operation is possible at any time

from the basic display, even if automatic pro-

grammes are active. Operation may however be

locked (see locking/unlocking operation).

Press the or button.p q

Short press on button: Adjustment of the slat

position.

Long press on button (> 0.5 s): Lock, shutter

moves to nal position.

The max. operation time upon a long press on

the button is 2 minutes.

Short press on or button during the shut-p q

ter movement.

The shutter stops at the position reached.



If a protection signal (wind, rain) is present, no

move commands are executed (see Setting

Operating Mode).

Locking/unlocking operation

The operation buttons of the shutter timer can be

locked, in order to prevent unintentional operation,

e.g. by children.

The shutter timer shows the basic display.

Press the button for more than 5 seconds.á

is shown in the display. The operation but-

tons are locked.

Press the button again for more than 5 á

seconds.

disappears in the display. The operation

buttons are enabled.

Opening the menu and navigating

The shutter timer is set and programmed via the

menu.

o p e r a ti n g

m o d e

h o l i d a y

mode

(17)

(15)

(16)

Fig. 3: Main menu

(15) Selected menu item

(16) Position display of the selected menu item in

the list of options

(17) Next option in the list

Short press on any button.

Operation is activated. The display is illuminated.

Press the button for more than 2 seconds.OK

The main menu is displayed. The rst menu

item (Fig. 3, 15) is highlighted operating mode

dark.

Press the or button to navigate through p q

the menu.

The selected menu item is highlighted dark.

Conrm the selected option by pressing OK.

The submenu opens.

Navigation through the menus can continue as

described above.

Press the button.á

The display switches to the previous contents.

To return to the basic display, press the á

button multiple times as necessary.

manual operation

P1: 7 - 21h

P2: 7 - 21h + 8 - 22h

(astro mode)

party mode

(activation)

(deactivation)

Deutsch

English

Francais

country-city selection

coordinates

>2 s

language

time settings

astro settings

factory settings

summer/winter time

operating

mode

holiday

mode

program

settings

time / date



modify

(restore defaults) 



advanced

settings



standalone

mode

(activation)

(deactivation) 

configuration

select quicklink

function

quicklink settings 

0 7 3: 0

Wednes d ay

1 2 4: 1

2 1 2: 0











































display settings

Displayed in

selected language

(e.g.: English)

(18) (19)

(20)

(21)

(22)

(23)

(26)

(27)

(25)

Figure 4: Menu overview

If no button is pressed for a period of two mi-

nutes, the display returns to the basic display.

Figure 4 shows an overview of the functions in the

menus/submenus: for the user and for the A.. E..

electrician refer to sections for additional informa-

tion Menu items in brackets are visible depending .

on the timer programming status.

Setting the values

Values, such as time or date, have to be set rst

for the programming of some functions.

The value to be set is selected and is highlighted

dark.

Press the or button.p q

Short press on button: Change the value by

one step.

Keep button pressed: Scroll through values.

Scrolling stops when the button is released.

M o n d a y - S u n d a y

0 6 : 00

(28)

If operation times are set, then a symbol (28)

shows whether it is an UP or DOWN operation

time.

Press the button.OK

The set value is applied.

Press the button.á

The display switches to the previous value. The

setting is not applied.

Submenu A1 - Select programme

One can choose between the following pro-

grammes:

- : manual operation

Operation takes place solely using the buttons

(see Operate shutter - operation from the basic

display).

- Time programmes and P1: 7 - 21 h P2: 7 - 21

h + 8 - 22 h :

These programmes are factory preset but can

be changed individually.

P1 is a week programme with identical operati-

on times for each day, is a week/weekend P2

programme with di󰀨erent operation times for

Mon. - Fri. and Sat. - Sun.

- astro mode:

Programme for dawn/dusk-dependent control

of the shutters (see submenu A7 - Setup Astro

programme).

The astro mode is only displayed if it has been

set up.

- : party mode

The Party programme prevents unintentional

operation of the controlled blinds/shutters by

programmed operation time or extension unit

operation, e.g. to prevent people from being

shut out by the shutter going down.

When the Party programme is active, a blind/

shutter can only be operated manually using

the buttons on the timer. Control of the shutter

via high-level control-sections and sensors as

well as by extension units, radio and forced

control commands is deactivated.ontrol of the

shutter by higher-level control-sections and

sensors as well as by extension units, radio

and forced control commands is deactivated.

If the blind/shutter was moved to a dened po-

sition in (see Table 4) and this forced mode

forced mode is active, then the Party pro-

gramme cannot be selected.

The shutter timer shows the Programme selection

submenu (Fig. 4, 19). The most recently selected

programme is highlighted dark.

ma n u a l o p e ra t i o n

P 1 : h 7 - 2 1

P 2 : h + h 7 - 2 1 8 - 2 2

Press the or button to select the desired p q

programme.

Press the button.OK

The screen switches to the basic display. The

selected programme is run, the corresponding

symbol (Table 1) is shown in the display (Fig.

2, 13).

Submenu A2 - Change, delete or add to

programmes

The options and (Figure modify restore defaults

4, 22) can be used for the preset factory pro-

grammes:

- to adapt, add to or delete operation modify

times. A maximum of 20 operation times per

day are possible.

- -restore defaults to reset a modied pro

gramme to the factory default programming.

Switching times can only be edited individually

under . It is not possible to edit pro-modify

gramme blocks (e.g. Mon. - Fri.).

Press the or button to select options or to p q

change the values.

Press the button.OK

Short press on button: Conrmation of the

current selection or the set value.

Long press on button (> 2 s) in programme edi-

ting: Adding an extra switching time or deletion

of an existing switching time.

a dd s t ep

de le te

Press the button.á

Short press on button: The display switches to

the last content.

Long press on button (> 2 s): Programming is

completed, the switching times are skipped.

Changes can be saved or rejected.

save

m o d i f i c a t i o n s ?

Y e s N o

Should no DOWN operation time follow an UP

operation time, or vice-versa, then the user is

informed on the display before saving, that

switching times are missing. Saving is never-

theless possible.

attention

i n co m p le t e s eq u e nc e

Submenu A3 - Activating/deactivating Holiday

programme

The Holiday programme is a simple form of the

presence simulation. The operation times of an

existing programme (P1, P2, Astro) are varied,

randomly, by ± 15 minutes. If operation times are

too close together (di󰀨erence < 15 minutes), then

they are not varied.

The shutter timer can be found in the submenu

holiday mode (Fig. 4, 20).

Conrm activation with .OK

The screen switches to the basic display and

the symbol for is displayed holiday mode

(Fig. 2, 13).

or:

Conrm deactivation with .OK

The screen switches to the basic display and

the symbol for is hidden in holiday mode

the display.

Submenu A4 - Activating/deactivating Stand-

alone programme

The Stand-alone programme can be used for

radio installations, in which the shutter timer was

assigned to a master shutter control as a subordi-

nate control. In Stand-alone operation the device

ignores the radio commands of higher-level master

controls and forced control commands, as well as

extension unit signals, i.e. operation commands

concerning the local blind/shutter are not execut-

ed.

If the blind/shutter was moved to a dened po-

sition in (see Table 4) and if this forced mode

forced mode is active, then the Stand-alone

programme cannot be selected.

The shutter timer can be found in the submenu

standalone mode (Fig. 4, 21).

Conrm activation OK with .

The screen switches to the basic display and

the symbol for is displa-standalone mode

yed (Fig. 2, 13).

or:

Conrm deactivation OK with .

The screen switches to the basic display and

the symbol for normal radio operation

is displayed (Fig. 2, 13).

Submenu A5 - Set time/date

In the main menu (Fig. 4, 18), is high-time/date

lighted dark.

Short press on button.OK

The hour display as an active element is high-

lighted dark.

Set the date and time (see Setting values).

When all the setting options have been run

through, the screen returns to the basic display.

Submenu A6 - Set time options

The automatic switching to standard/daylight

saving time can be activated or deactivated for the

shutter timer.

The submenu is displayed (Fig. 4, time settings

25).

Conrm the summer/winter time option by

pressing .OK

a u t o

m a n u a l

Press the buttons or to select the required p q

setting and conrm by pressing OK.

The device applies the setting and returns to

the submenu .time settings

Submenu A7 - Setup Astro programme

The Astro programme leads to a dusk/dawn depen-

dent control of shutters, meaning that automatic

operation time adjustment occurs according to the

season. As these operation times can be very early

or very late, the Astro programme o󰀨ers enhanced

options in order to adapt the operation time.

- Deviation from dawn time by ± 120 minutes

- Deviation from dusk time by ± 120 minutes

- Earliest UP operation time ( ) earliest up time

No operation times are executed before the

earliest UP time, as dened by dawn. The blind

moves UP at the time set here.

Astro operation times after the set time are

executed normally.

Example:

Set time

earliest up time

Sunrise Executed

operation time

06:15 07:32 07:32

05:23 06:15

- Latest DOWN operation time (latest down ti-

me)

No operation times are executed after the latest

DOWN operation time, as dened by dusk. The

shutter moves DOWN at the time set here.

Astro operation times before the set time are

executed normally.

Example:

Set time

latest down time

Sundown Executed

operation time

20:00 17:42 17:42

21:12 20:00

The installation location must be set to determine

the correct Astro operation times.

- Country/city selection:

Simple setting option by selecting a country

and a city near the location from a comprehen-

sive list of European cities.

- The setting is made by entering the geographic

co-ordinates and time zone of the location.

If the location is outside Europe or a high level

of accuracy is required for the Astro operation

times, then the setting should be made using

the co-ordinates.

The submenu is displayed astro settings

(Fig. 4, 26).

Press the buttons or to select the setting p q

type and conrm by pressing OK.

The country/city selection and the co-ordinate

settings are displayed.

Operation and

installation instructions

Berker GmbH & Co. KG

Zum Gunterstal

66440 Blieskastel/Germany

Tel.: + 49 6842 945 0

Fax: + 49 6842 945 4625

E-Mail: info@berker.de

www.berker.com

05/2022

6LE008041A

KNX radio shutter timer quicklink

Order-No. 8574 51 ..

Produkt Specifikationer

Mærke:	Hager
Kategori:	Ikke kategoriseret
Model:	85745139
Kode for international beskyttelse (IP):	IP20
Antal pr. pakke:	1 stk
Driftstemperatur (T-T):	-5 - 45 °C
Antal produkter inkluderet:	1 stk