Hager REQ004X Manual

Hager Ikke kategoriseret REQ004X

Læs gratis den danske manual til Hager REQ004X (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om Hager REQ004X, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

6LE000691A

REQ0..X, REQ1..X

Door station AUDIO 2wire

Safety instructions

Electrical equipment may only be installed and

assembled by a qualiﬁ ed electrician in accord-

ance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

When installing and laying cables, always com-

ply with the applicable regulations and stand-

ards for SELV electrical circuits.

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

(5)

(4)

(1)

(2)

(3)

(6)

Figure 1: Design and layout of the device front

(1) Front plate stainless steel

(2) Microphone

(3) Door loudspeaker

(4) Twilight sensor for call button

(5) Button panel with call push-buttons

(6) Cover strip for dismantling protection

(10)

(7)

(8)

(9)

TOP

(11)

(12)

Figure 2: Design and layout of the device back

(7) Adjustment button Upwards

(8) 7-segment display

(9) Selection button

(10) Adjustment button downwards

(11) Module bus connector

(12) Connection terminal block

Function

The audio door station works in the 2wire bus sys-

tem and enables communication via sound.

Correct use

- for surface- or  ush-mounted installation

- not compatible with intercom systems of other

manufacturers

- suitable for use exterior applications

Product characteristics

- completely pre-assembled

- protected against vandalism

- with brushed 2 mm stainless steel front plate

- Name plate can be changed from the front with-

out any special tools

- One-man commissioning

- call button with acknowledge tone (can be

switched off) and tactile feedback

- call button, light release or door release can be

adjusted even without any function

- durable, homogeneous, white LED call

push-button backlighting

- Twilight controlled call push-button backlighting

with adjustable switch-on brightness level

- Opening of door station only with enclosed

opening tool

- break-proof  ush-mounted call buttons

- Loudspeaker and microphone protected against

sabotage

- Volume and microphone sensitivity settable

- Door release contact on 1 ... 10 s adjustable

- Door release without previous call adjustable in

single door systems

- Safety rope as installation aid

Operation

Establish call (ringing)

zPress the call push-button assigned to the

desired subscriber.

If con gured, the call push-button activation is

con rmed by an acknowledge tone. Addressed

indoor stations are called.

Switch-on lights

A call push-button is con gured and labelled for

lighting control (light insert supplied).

zPress the call push-button for lighting.

zIf con gured, the call push-button activation is

con rmed by an acknowledge tone. The light

contact of a line power supply is closed for the

set time.

Label call push-button

zKeep call push-button pressed on one side.

On the opposite side, the lever opening (14) is

accessible for a screwdriver.

zPosition the screwdriver in the lever opening

(13) and release the interlock (Figure 3).

zRemove cover with name plate insert.

(13)

Figure 3: name plate change

(13) Lever opening

zLabel name plate insert if required.

zInsert name plate insert, prepared foil or pre-

pared labelling strip into the cover and press on

cover.

Do not use any paper for the name plate insert,

since moisture and UV light will damage the

paper and labelling.

UV-resistant foil with laser printing is suitable

for labelling as well as labelling devices for

labelling strip:

- small buttons - 12 mm

- medium buttons - 30 mm

Door stations with status indication

Dis-

play

Cause Function/Lighting

duration

A subscriber is

called.

After 90 s without call

acceptance or an opera-

tion on the door station,

goes out.

A subscriber

accepts the

door call.

goes out, lights up

as long as the intercom

connection is pressed

down, max. 3 min.

The door is

unlocked.

Call not accepted:

Symbol goes out and

lights up for the un-

locking time set on the

door station.

Call accepted:

In addition to the

the

lights up for the un-

locking time set on the

door station. goes out

approx. 5 sec after the

symbol.

Table 1: Status indications of door station

Cleaning and care

Commercially available products for stainless

steel and car paintwork care containing a wax

component for conservation are recommended for

cleaning and care.

Do not use wire wool, wire brushes or any

similar products for cleaning. This will prevent

damage to the surface and accumulation of

 ash rust.

Information for electricians

Installation and electrical connection

DANGER!

Touching live parts in the installation

environment can result in an electric

shock!

An electric shock can be lethal!

Before working on the device or load,

disconnect all associated circuit brea-

kers. Cover all live parts in the area!

When installing door communication systems,

comply with the general safety regulations for tele-

communications systems according to VDE 0800:

- Separate routing of power and door communi-

cation cables with a minimum spacing of 10 cm

- Partitions between power and door communica-

tion cables in shared trunkings

- Use of standard telecommunications' cables, e.

g. J-Y (St) Y with 0.8 mm diameter

Bus cables

- J-Y(ST)Y or A-2Y(L)2Y

Use wrapped wire pair.

Recommendation: white/yellow

- CAT

Use wrapped wire pair.

Recommendation: orange/white

- YR

Use adjacent wires.

Mounting door station

Surface-mounted or  ush-mounted housing is

installed (see Assembly instruction housing).

The connection cables and indoor stations are

connected to the line power supply while taking

the maximum cable lengths and attenuations into

account (see operating instructions of the line power

supply).

zThe fastening elements supplied with the

 ush-mounted housing must be assembled with

the nuts on the top and bottom on the threaded

bolts. The support bracket (14) of the fastening

elements must be located on the wall surface.

(14)

Figure 4: Support bracket of the fastening elements

(14) Support bracket of the fastening elements

zInsert opening tool (15) into the mounting de-

vice of the lower fastening element (16) on the

housing (Figure 5).

(15)

(16)

Figure 5: Inserted opening tool

(15) Opening tool

(16) Fixing element

zAttach the loops of the safety rope (17) to the

upper left suspension of the door station and to

the upper fastening element (18) in the housing.

Place the door station for installation onto the

opening tool (Figure 5).

(18)

(17)

Figure 6: installation position of door station

Individual call push-

button address/function

Automatic call push-

button addressing

Door speaker

volume

Microphone sensiti-

vity

Operating sig-

nal sound volume

Door release

unlocking time

Door release

function

set

door address

Camera present

Call push-button

Backlighting

settings

(switch-on bright-

ness level)

Display error

codes (max. 5 can

be saved)

Reset error codes

factory setting

Conﬁ rm the call

push-button to be set

= Cancel

= Start addressing

...

Default setting

...

Default setting

...

= Acoustic signal off

Default setting

... Seconds

Default setting seconds

= only with door call

= also without door call 1)

Default setting

x ... x

x = received line

address

Default setting

= No camera

= with camera

Default setting: Audio

Video

...

= Off

= lowest value

= highest value

= always on

Default setting

... Error codes

= module communication

= sticking call button

= module address

= no error present

= Cancel

= Reset

= Cancel

= Reset

1) Door release functions without door call only possible

Figure 7: Overview

Produkt Specifikationer

Mærke:	Hager
Kategori:	Ikke kategoriseret
Model:	REQ004X

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager REQ004X stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Hager Manualer

10 Juni 2025

10 Juni 2025

10 Juni 2025

12 Januar 2025

Hager Vision VKG004A-T Manual

11 Januar 2025

Hager GS11019016 Manual

30 December 2025

30 December 2025

30 December 2025

30 December 2025

30 December 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Simrad Active Imaging HD (Thru-Hull) Manual

14 Juni 2025

Garritan Harps Manual

14 Juni 2025

Marshall CV-H20-HF Manual

14 Juni 2025

Aiphone IXW-MAA Manual

14 Juni 2025

Rival HM-743 Manual

14 Juni 2025

Lutec Avony Manual

14 Juni 2025

Giordani G-SAFE & PLAY Manual

14 Juni 2025

Gourmia GAF799 Manual

14 Juni 2025

Arendo 307503 Manual

14 Juni 2025

Hughes & Kettner Tube 100 Manual

14 Juni 2025