Hager REQ524X Manual

Hager Ikke kategoriseret REQ524X

Læs gratis den danske manual til Hager REQ524X (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 52 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 26.5 anmeldelser. Har du et spørgsmål om Hager REQ524X, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

6LE000719A

REQ5..X, REQ6..X

Door station VIDEO 2-wire

Safety instructions

Electrical equipment may only be installed and

assembled by a qualiﬁ ed electrician in accor-

dance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

When installing and laying cables, always com-

ply with the applicable regulations and stan-

dards for SELV electrical circuits.

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

(7)

(3)

(6)

(4)

(5)

(2)

(1)

Figure 1: Front

(1) Front plate stainless steel

(2) Microphone

(3) Camera

(4) Locating screw for camera

(Allen key supplied)

(5) Twilight sensor for call button/loudspeaker

(6) Button panel with call push-buttons

(7) Cover strip for dismantling protection

(11)

(8)

(9)

(10)

(12)

(13)

Figure 2: Back

(8) Adjustment button Upwards

(9) 7-segment display

(10) Selection button

(11) Adjustment button downwards

(12) Module connecting cable

(13) Connection terminal block

Function

The door station video works in the 2-wire bus

system and enables communication via sound and

image.

Correct use

- for surface- or ﬂ ush-mounted installation in spe-

cial housings (see Accessories)

- Not compatible with intercom systems of other

manufacturers

- suitable for use exterior applications

Product characteristics

- completely pre-assembled

- protected against vandalism

- with brushed 2 mm stainless steel front plate

- Name plate can be changed from the front wit-

hout any special tools

- One-man commissioning

- Call push-button with acknowledge tone (can

be switched off) and tactile feedback

- Call button, light release or door release can be

adjusted even without any function

- durable, homogeneous, white LED call push-

button backlighting

- Twilight controlled call push-button backlighting

with adjustable switch-on brightness level

- Opening of door station only with enclosed ope-

ning tool

- break-proof ﬂ ush-mounted call buttons

- Colour camera

- invisible, glare-free IR LED night lighting

- temperature controlled camera heating for clear

view

- scratch-proof camera cover

- Loudspeaker and microphone protected against

sabotage

- Volume and microphone sensitivity settable

- Door release contact on 1 ... 10 s adjustable

- Door release without previous call adjustable in

single door systems

- Safety rope as installation aid

Operation

Establish call (ringing)

Press the call push-button assigned to the

desired subscriber.

If conﬁ gured, the call push-button activation is

conﬁ rmed by an acknowledge tone. Addressed

indoor stations are called.

Switch-on lights

A call push-button is conﬁ gured and labelled for

lighting control (light insert supplied).

Press the call push-button for lighting.

If conﬁ gured, the call push-button activation is

conﬁ rmed by an acknowledge tone. The light

contact of a line power supply is closed for the

set time.

Label call push-button

Keep call push-button pressed on one side.

On the opposite side, the lever opening (14) is

accessible for a screwdriver.

Position the screwdriver in the lever opening

(14) and release the interlock (Figure 3).

Remove cover with name plate insert.

(14)

Figure 3: Removing name plate cover

(14) Lever opening

Label name plate insert if required.

Insert name plate insert, prepared foil or prepa-

red labelling strip into the cover and press on

cover.

Do not use any paper for the name plate insert,

since moisture and UV light will damage the

paper and labelling.

UV-resistant foil with laser printing is suitable

for labelling as well as labelling devices for

labelling strip:

- small buttons - 12 mm

- medium buttons - 30 mm

Door stations with status indication

Dis-

play

Cause Function/Lighting

duration

A subscriber is

called.

After 90 s without call

acceptance or an operati-

on on the door station,

goes out.

A subscriber

accepts the

door call.

goes out, lights up

as long as the intercom

connection is pressed

down, max. 3 min.

The door is

unlocked.

Call not accepted:

Symbol goes out and

lights up for the unlok-

king time set on the door

station.

Call accepted:

In addition to the

the

lights up for the un-

locking time set on the

door station. goes out

approx. 5 sec after the

symbol.

Table 1: Status indications of door station

Cleaning and care

Commercially available products for stainless

steel and car paintwork care containing a wax

component for conservation are recommended for

cleaning and care.

Do not use wire wool, wire brushes or any

similar products for cleaning. This will prevent

damage to the surface and accumulation of

ﬂ ash rust.

Information for electricians

Installation and electrical connection

DANGER!

Touching live parts in the installation

environment can result in an electric

shock!

An electric shock can be lethal!

Before working on the device or load,

disconnect all associated circuit brea-

kers. Cover all live parts in the area!

When installing door communication systems,

comply with the general safety regulations for tele-

communications systems according to VDE 0800:

- Separate routing of power and door communi-

cation cables with a minimum spacing of 10 cm

- Partitions between power and door communica-

tion cables in shared trunkings

- Use of standard telecommunications' cables, e.

g. J-Y (St) Y with 0.8 mm diameter

Bus cables

- J-Y(ST)Y or A-2Y(L)2Y

Use wrapped wire pair.

Recommendation white/yellow

- CAT

Use wrapped wire pair

Recommendation orange/white

- YR

Use adjacent wires

Mounting door station

Surface-mounted or ﬂ ush-mounted housing is

installed (see Assembly instruction housing).

The connection cables and indoor stations are

connected to the line power supply while taking

the maximum cable lengths and attenuations into

account (see operating instructions of the line power

supply).

The fastening elements supplied with the ﬂ ush-

mounted housing must be assembled. To do

this, loosen the nuts on the threaded bolts, slide

the elements onto the bolts over the 2 nuts and

then tighten.

The support bracket (15) of the fastening

elements must be located on the wall surface

(Figure 4).

(15)

Figure 4: Installation position of fastening elements

(15) Support bracket of the fastening elements

Insert opening tool (16) into the mounting de-

vice of the lower fastening element (17) on the

housing (Figure 5).

(16)

(17)

Figure 5: Inserted opening tool

(16) Opening tool

(17) Fixing element

Attach the loops of the safety rope (17) to the

upper left suspension of the door station and to

the upper fastening element (16) in the housing.

Place the door station for installation onto the

opening tool (Figure 5).

(18)

(17)

Figure 6: installation position of door station

(18) Safety rope

Connect door station

Shorten connection cable of the door station

and strip the required wires.

Pull off connection terminal block (13) from the

video insert.

Connect the wire pair of the 2-wire bus cable

to the terminals of the connection terminal XX

block (Figure 7).

Connect door release to the terminals of TT

the connection terminal block (ﬁ gure 7 and 8) if

required.

or:

For manipulation-protected installation, connect

the door release to the contact of the line

power supply (Figure 9).

The door release lead must not be inserted

through the door station in order to protect

against manipulation.

For call push-button backlighting and camera

heating connect 12 V~ lead from the power

transformer to the terminals of the connec-~~

tion terminal block (Figure 7).

(13)

Figure 7: Wired connection terminal block

Information on the connection as a ﬂ oor door

station can be found in the operating instruc-

tions of the line power supply.

Attach connection terminal block to video insert.

Produkt Specifikationer

Mærke:	Hager
Kategori:	Ikke kategoriseret
Model:	REQ524X

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager REQ524X stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Hager Manualer

22 Juli 2025

22 Juli 2025

22 Juli 2025

21 Juli 2025

21 Juli 2025

21 Juli 2025

21 Juli 2025

Hager EC12125CT Manual

21 Juli 2025

Hager RED361X Manual

21 Juli 2025

Hager REE500X Manual

21 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Advantech AIR-020 Manual

29 Juli 2025

Tefal Optiss BC5109 Manual

29 Juli 2025

Teslong MS100-C Manual

29 Juli 2025

Advantech TPC-651T Manual

29 Juli 2025

Advantech TPC-B510 Manual

29 Juli 2025

Advantech ARK-1220L Manual

29 Juli 2025

Gravity MS 0200 SET1 Manual

29 Juli 2025

Advantech FWA-5072 Manual

29 Juli 2025

Moulinex Oveo DD3001 Manual

29 Juli 2025

Silvergear E-reader Manual

29 Juli 2025