Hager TG053A Manual

Hager Ikke kategoriseret TG053A

Læs gratis den danske manual til Hager TG053A (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Hager TG053A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

User instructions

Presentation

The weather station GPS-KNX TG053A measures

the outdoor temperature, the wind speed and the

brightness.

It detects rain and daylight fall.

The weather station gets date/time and site loca-

tion data from GPS signals. It calculates also the

exact position of the sun (Azimuth and Altitude)

based on site co-ordinates and date/time data.

This information (brightness level and sun posi-

tion) is used to control blinds with slats based on

sun tracking for up to 6 building frontages.

TG053A compact case houses all sensors, elec-

tronic data processing gear, GPS antenna and

KNX bus connection.

The values measured are sent to the KNX bus as

physical values (2x8 bits ou 1 bit).

Each output has communication objects indica-

ting the measured and calculated values.

The state of outputs depends on one or more

levels.

Thresholds can be defined by settings or the

communication objects.

The weather station TG053A includes an annual

clock and a weekly clock. The clock channels can

switch the outputs using the communication

objects.

The weekly clock controls up to four different time

settings for each day of the week.

The annual clock can be used to define up to

three periods in the year with two daily ON/OFF

commands for each of them.

The switching times can be defined by settings or

the communication objects.

The weather station also has 8 logical AND gates

and 8 logical OR gates, each with four inputs.

All control events, time programs, and the 8 logi-

cal inputs (such as communication objects) can

be used as inputs of logical gates.

GPS, site location, date and time

The exact site location co-ordinates are received

from GPS signals. This information is required to

manage summer/winter time changes automati-

cally. On its first startup, the weather station uses

site location and date/time data provided by ETS

software until the first GPS signal is received.

Depending on ETS settings, the weather station

can process date/time information received from

GPS or KNX bus.

Installation and startup

Only qualified technicians must install, check,

start up and repair the appliance. Make a note of

all the lines to be installed with the appliance swit-

ched off and protect them against risks of being

powered up.

The weather station is designed only for the uses

described in this user manual. Any non-compliant

changes or breaches of the specifications in this

user manual will render the warranty null and void.

Check that the appliance is complete and in per-

fect condition (no mechanical damage) immedia-

tely after unpacking it.

If damage has occurred during transportation,

inform the supplier immediately.

If use without danger is not possible, switch off

the system and protect it against an accidental

restart.

The weather station must be used as a fixed sys-

tem. It must only be started after all the installa-

tion works have been completed and in an envi-

ronment designed for this purpose.

Hager refuses any liability for possible changes to

standards that may be made after the publication

of these instructions.

Location

Legend :

1. Spring-force auxiliary voltage terminal, suitable

for solid conductor up to 1.5 mm² or fine wire

conductor. Terminal assignment independent

of polarity (+/- or -/+).

2. Rain detector wiring connector included in box

cover

3. GPS antenna

4. GPS Signal LED

5. Connector KNX (+/-)

6. Physical addressing button

7. Physical addressing LED.

Technical characteristics

The output of each gate can be configured in

1-bit or 2 x 8-bit format.

ETS software performs KNX configuration.

ETS : application software (database and

Installation Guide with descriptions available from

the Manufacturer).

Never start up a weather station that shows

signs of damage.

Select a clear site that allows for correct

measurements by the wind, rain and sun sensors.

South direction is advised for correct measurement

of brightness level.

The weather station must never be installed

beneath structures from which water may fall onto

the rain sensor after the end of the precipitations

(rain or snow).

The weather station must never be placed in the

shadow of a building or trees.

Arrange a space of at least 60 cm under the

weather station to allow for correct wind

measurements and to prevent snow from covering

the sensor.

Other factors may also interfere with or affect the

reception of the GPS signal, such as magnetic

ﬁ elds, transmitters or radioelectrical interference

from ﬂ uorescent light tubes, neon signs, switch

mode power supplies, etc.

RF 24 V

TP Bus

30 V

Frequency range 1 559 -1 610 MHz

KNX Medium TP 1

Configuration mode S-Mode

KNX default address 15.15.255

(changable in ETS)

Rated voltage KNX 30 V SELVs

Current consumption KNX max. 8 mA

Auxiliary voltage 12 … 40 V SELVs

v 12 … 28 V SELV

Auxiliary current max. 185 mA at 12 V s

max. 81 mA at 24 V s

Operating temperature -30 … + 50 °C

Operating altitude max. 2000 m

Storage/transport temperature -30 … +70 °C

Dimensions (W x H x D) ca. 96 x 77 x 118 mm

Weight 170 g

Degree of protection IP44

Surge voltage 1500 V

Overvoltage category III

Degree of contamination 2

Software class A

Action type type 2

Precipitation sensor:

Measurement precipitation Yes/No (1 bit)

Heating approx. 1.2 W

Temperature sensor:

Measuring range -30 … +80°C

Resolution 0.1 °C

Measuring accuracy ±1°C at -10…+85°C,

±1,5°C at -25…+150°C

Wind sensor:

- Measuring range 0 … 35 m/s

- Resolution 0.1 m/s

- Measuring accuracy ± 15% of measured value

Brightness/twilight sensor

- Measuring range 0 lx … 150 klx

- Measuring accuracy ± 15 % at 10 … 150 klx

1 6LE002905C

6LE002905C

TG053A

zWeather station GPS-KNX

oVærstasjonen GPS-KNX

Produkt Specifikationer

Mærke:	Hager
Kategori:	Ikke kategoriseret
Model:	TG053A

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager TG053A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Hager Manualer

Hager WXF228 Manual

10 August 2025

Hager UKM340480 Manual

10 August 2025

Hager TRC301B Manual

10 August 2025

Hager GS20109011 Manual

10 August 2025

Hager AKB42000402 Manual

10 August 2025

Hager WXT312 Manual

10 August 2025

Hager BKSAN065110 Manual

10 August 2025

Hager VR10127011 Manual

10 August 2025

Hager UKM240280 Manual

10 August 2025

Hager ESR3336029 Manual

10 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025