Hager TXA664D Manual

Hager Skifte TXA664D

Læs gratis den danske manual til Hager TXA664D (2 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Hager TXA664D, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Safety instructions

Electrical devices must only be installed and

assembled by a qualied electrician. The

accident prevention recommendations

applicable in the country must be followed.

Failure to follow the installation instructions

may result in damage to the device, re or

other dangers. Please follow the

recommendations and standards applicable for

SELV electrical circuits during installation and

when laying cables. Before any work on the

device or the load, switch off the power to the

installation. Do not forget all the circuit

breakers that deliver voltages which are

potentially dangerous to the device or the load.

Risk of electric shock. The device is not

suitable for disconnection/sectioning. These

instructions are an integral part of the product

and must be kept by the end user.

How to dispose of this product (electrical

and electronic equipment waste). (Applicable

in European Union countries and other

European countries with selective waste

collection systems). This symbol on the product

or its documentation indicates that it must not be

disposed of with other household waste at the end of its

life cycle. As disposing of waste inappropriately may harm

the environment or human health, please separate it from

other types of waste and recycle it responsibly. In this

way you will contribute to the sustainable re-use of

material resources.

Individuals should contact the retailer who sold them the

product or contact their local council to nd out where

and how they can dispose of this product for recycling in

an environmentally friendly manner. Companies should

contact their suppliers and read the terms of their sales

contract. This product must not be disposed of with the

other commercial waste.

6LE005516A

TXA664D

DALI broadcast

4 output module

Presentation of the device

N L

da da da da da da da da+ - + - + - + -

C1 C2 C3 C4

C2 C3 C4

TXA664D 4X DALI broadcast

I> 185mA

Hager Controls BP10140 67703 SAVERNE CEDEX FRANCE

TP / S

Image 1: presentation of the device

1 Connection to the power supply (N, L)

2 Connections to the DALI ballasts (da+, da-)

3 Auto/Manu switch ( )

4 Status LED

5 Local command buttons

6 Illuminated physical addressing button

7 Label holder

8 KNX bus connection terminals (-, +)

9 Overload fault LED

Function

System information

This device is a product of KNX system and

complies with KNX guidelines. Detailed,

specialised knowledge obtained through specic

KNX training courses is required for full

understanding of the system. The device is

programmed, installed and started up with

certied KNX software.

ETS start-up

The functions of this device are software- and

conguration-dependent. The application software

is available in the product database. The product

database, technical descriptions and conversion

programmes as well a other up-to-date assistance

software are available on our website.

Easy start-up

The functions of this device are software- and

conguration-dependent. It can also be congured

a tool specically developed for easy set-up and

start-up.

This conguration method is only possible with

devices which are compatible with the Easy

system. The Easy conguration method allows for

simple set-up through a graphic interface.

Precongured standard functions are assigned to

the in/outputs by means of the conguration tool.

Functional description

The TXA664D 4-output module is used to control

DALI ballasts over the KNX bus in single master

broadcast mode.

This product is DALI2 certied.

Typical scenario

Integration in the electrical box and rail mounting

in accordance with DIN EN 60715.

Product features

• ON/OFF and dimmer control.

• Adjustable colour temperature (warm white/cool

white) with the DT8 ballast.

• Adjustable RGB/RGBW colour with the DT8

ballast.

• Compatible with DALI ballasts (see chapter:

Compatible ballast types).

• Possibility of manually controlling outputs on the

device, site mode.

• Product secured against overloading and

short-circuits (see chapter: Meaning of LEDs).

• Bus connection with the KNX connection

terminals.

Short-circuit protection

To protect the device and the connected ballasts

in case of short-circuit, the device determines the

output concerned. During this search cycle, the

product disables the output group (C1 + C2 + C3

+ C4) according to the faulty outputs. Once

identied, the latter remain disabled, and the

others return to automatic mode.

This behaviour complies with the short-circuit

behaviour set out in the IEC 62386-101 standard.

Protection against overloading

In case of overload, the device deactivates all the

outputs and warns of an overload fault by

illuminating the LED.

Test and start-up

Auto/Manu switch and local command buttons 3

• Switch 3 set to Manu(al) ( ).

Short presses on the push buttons turn the 5

output on and off.

Long presses alter the brightness.

• Use the Switch Auto position in operating 3

mode or to congure the product.

In switch Auto position , the buttons are 3 5

inactive and the outputs respond to orders from

the KNX bus.

Meaning of LEDs 4

Illuminated physical addressing button 6

Press the illuminated button to physically 6

address the product or check the presence of the

bus (LED lit = bus presence and product physically

addressed).

Assembling the device

Irrespective of the assembly used (in an electrical

box on DIN rail or in a wall mounted box), you

must ensure the device is at the right temperature

with sufcient cooling. For wall mounting in a box

outside the electrical cabinet, Hager recommends

the item TGC600.

Compatible ballast types

In accordance with IEC 62386, ballasts are

categorised according to Device Type (DT).

DTs that are compatible with the product are listed

below:

DT0 = uorescent lamps

DT2 = discharge lamps

DT3 = low voltage halogen lamps

DT4 = incandescent lamp dimmers

DT5 = digital signal to DC voltage converters

DT6 = LED modules

DT7 = switching (ON/OFF only) control gear

DT8 = colour and colour temperature control gear

The emergency lighting (DT1) ballasts are

not compatible with the product.

Number of ballasts to connect

When designing an installation, ensure that the

total consumption of the ballasts for the product

as a whole does not exceed 185 mA. There are no

restrictions on product channel distribution.

You must refer to the ballast technical sheets

when designing your installation

and base your calculations on the worst-case

scenario.

LED LED/Operation status

output active

output inactive

short-circuit detected, ashes

every 0.5 s

no ballast or lamp fault, ashes

every 0.5 s for 5 s

Image 2: LED operation and status

230V~

Hager Controls S.A.S., 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France - www.hager.com

red

Start-up

ETS

Loading the physical and application software

address:

• switch on the bus voltage,

• press the programming key,

• load the physical address in the device,

• download the application software to the device,

• note the physical address on the device label,

• stick the label to the device.

If an incorrect ETS application is loaded,

LEDs C1 to C4 will ash red.

Easy

Refer to the detailed description of the easy link

service module for more information on the

conguration of the installation.

Technical features

Conguration mode .......................... ETS and Easy

KNX communication media TP1 ..............................

Mains supply

Product power supply voltage:

- 230 V~ +10/-15 % .................................................

- 240 V~ +/-6 % .......................................................

Network frequency 50 / 60 Hz .................................

Typical consumption 900 mW .................................

KNX

KNX power supply voltage 20...30 V SELV ........... ⎓

Consumption on the KNX bus:

- typical 2.35 mA ......................................................

- in standby 1.7 mA .................................................

DALI

DALI power supply voltage . 16 V FELV ................ ⎓

Guaranteed current 185 mA ....................................

Maximum current . 250 mA ......................................

Start up time < 500 ms ............................................

Ambient conditions

Operating temperature . -5 °C…+45 °C ...................

Storage / transport

temperature -20 °C … +70 °C .................................

Relative humidity 95% @ 20°C ................................

Pollution level 2 .......................................................

Box protection rating: IP 20 ....................................

Protection rating box under faceplate: IP30 .............

Impact resistance IK04 ............................................

Maximum operating altitude 2,000 m ......................

Surge voltage 4 kV ..................................................

Circuit breaker protection 10 A ................................

Box

Footprint 108 mm / 6 modules ................................

Installation method DIN rail in accordance with EN

60715

Output connection

Type of KNX connection KNX terminals ..................

Type of connection quick connect terminal .............

- rigid / exible ................................. 0.75...2.5 mm²

DALI cable length:

- Ø 1.5 mm² 300 m max. .........................................

- Ø 1.0 mm² 224 m max. .........................................

- Ø 0.75 mm² 168 m max. .......................................

The continuous overload detection

function built into the product can detect

whether too many ballasts are connected

to the product as a whole. If there are too

many, the overload fault LED shows red

(see § Protection against overloading).

Additional DALI power supplies must not

be added.

Connection diagram

• Device must only be installed by an

electrician.

• Follow the SELV installation rules.

• DALI control voltage is FELV -

Functional Extra-Low Voltage.

• Make sure you separate the KNX and

DALI circuits properly during

installation.

Image 3: 2 DALI ballasts wired up for single or

dual channel operation.

Hager 12.18 - 6LE005516A

N L

da da da da da da da da+ - + - + - + -

C1 C2 C3 C4

C2 C3 C4

TXA664D 4X DALI broadcast

I> 185mA

Hager Controls BP10140 67703 SAVERNE CEDEX FRANCE

TP / S

Ballast

N L

da da da da da da da da+ - + - + - + -

C1 C2 C3 C4

C2 C3 C4

TXA664D 4X DALI broadcast

I> 185mA

Hager Controls BP10140 67703 SAVERNE CEDEX FRANCE

TP / S

Ballast Ballast

Produkt Specifikationer

Mærke:	Hager
Kategori:	Skifte
Model:	TXA664D

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager TXA664D stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte Hager Manualer

3 April 2025

3 April 2025

31 Marts 2025

31 Marts 2025

31 Marts 2025

31 Marts 2025

31 Marts 2025

6 Februar 2025

6 Februar 2025

1 Januar 2025

Skifte Manualer

Nyeste Skifte Manualer

Lancom GS-2412 Manual

4 April 2025

Lancom GS-2412P Manual

4 April 2025

Lancom GS-2426 Manual

4 April 2025

Roline 14.01.3579 Manual

2 April 2025

Fantini Cosmi B12BN Manual

1 April 2025

Fantini Cosmi B12DN Manual

1 April 2025

Fantini Cosmi B12GN Manual

1 April 2025

Fantini Cosmi B12HN Manual

1 April 2025

Crestron CLW-LSWEX-2GD Manual

1 April 2025

Vimar 30181.120 Manual

1 April 2025