Hager TXM616D Manual

Hager Skifte TXM616D

Læs gratis den danske manual til Hager TXM616D (4 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Hager TXM616D, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

6LE002518A

TYM6..

Output 16A C-Load adapted /

shutter/blind

TXM6..

Output 16A C-Load adapted /

shutter/blind

Safety instructions

Electrical equipment may only be installed and

-

ance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

Failure to comply with these installation

instructions may result in damage to the



-



-

ous voltages to the device or load.



suited for safe disconnection of the mains

supply.







Connect one motor per output only.





switches for correct adjustment. Observe



get damaged.



device could get damaged.

Observe the motor manufacturer's data regard-

ing change-over time and max. switch-on time





of the product and must be retained by the end

user.



auto 1

auto 2

C1/C9 C3/C11 C5 /C13 C7/C15

C2/C10 C4 /C12 C6/C1 4 C8/C16

(1)

(2) (3)

(3)

(4)

(5)

(6)

Fig. 1: Example device variant 16/8gang

(1) Slide switch / 1/ 2

(2) KNX bus connection terminal

(3) Connections of loads

(4) Labelling eld

(5) Illuminated programming button

(6) Operation button for manual operation for

each pair of outputs with status LED

With variants 20/10gang the basic design corre-

sponds to the 16/8gang device variant.

Function

System information

This device is a product of KNX system and corre-

sponds to the KNX guidelines. Detailed specialised

knowledge obtained from KNX training courses

is required for understanding. The planning,

installation and commissioning of the device is

carried out with the help of KNX-certied software.



The function of the device is software-depend-

ent. The software is to be taken from the product

database. You can nd the latest version of the

product database, technical descriptions as well as

conversion and additional support programmes on

our website.



The function of the device is conguration-de-

pendent. The conguration can also be done using

devices developed specially for simple setting and

start-up.

This type of conguration is only possible with

devices of the easylink system. Easylink stands for

easy, visually supported start-up. Precongured

standard functions are assigned to the in/outputs

by means of a service module.

Functional description

The device receives telegrams from sensors or

other controllers via the KNX installation bus and

switches electrical loads with its independent relay

contacts. The devices are particularly suitable for

capacitive loads and are designed for high making

currents.

Correct use

- Switch electrical loads of 230 V AC with poten-

tial-free contacts.

- Switching electrically operated motors of 230 V

AC for blinds, shutters, awnings and similar

hangings.

- Mounting on DIN rail according to DIN EN

60715 in the distribution box.



- manual activation of the outputs on the device

possible, building site operation

- Status display of the outputs on the device

- Scene function

- Forced position by higher-level controller

- Connection of various external conductors

possible.

Functions in switch operation:

- Time switching functions

Functions in roller shutter/blind operation:

- Position can be started directly

- Slat position directly controllable

- Feedback of operating state, shutter position

and slat adjustment

- 3 Alarms

Operation



Bus voltage supply is present.

zPush switch (1) to position 1/ 2.

Manual operation is switched on, the outputs

can be controlled using the operation buttons

(6) independently of each other.

1 activates the control of the outputs

C1 C8 C1 C10 .. (16gang) resp. .. (20gang).

 activates the control of the outputs

C9 C16 .. (16gang) resp. C11 ..  (20gang).

During manual operation, the controller is deac-

tivated via the KNX bus.

Systemlink commissioning:

Depending on the programming, the manual

operation is activated permanently or for a time

period congured via the application software.

If the manual operation is blocked via the appli-

cation software, no activation takes place.

Or:

zMove switch (1) to position .

The manual operation is switched off. Operation

takes place solely via the KNX bus. The output

Bn,.:

adopts the position predened by the bus con-

troller. The switching status is displayed via the

status LED of the operation button (6).

auto 1 C1 displays the status of the outputs ..

C8 C1 C10 auto (16gang) resp. .. (20gang).

 displays the status of the outputs .. C9 C16

(16gang) resp. .. (20gang).C11 

Operating outputs in manual operation

Operation takes place per output by briey press-

ing the operation button repeatedly (table1).



-





when the motor is in unprogrammed



Motors, hangings and the device may



Always only press one button in man-

ual operation for unprogrammed

devices.

Status Behaviour when



Switching operation

Load is switched

off. Status LED of

the button (6) is off.

Switch ON the connected

load. Status LED of button

(6) lights up.

Load is switched

on, status LED

of the button (6)

lights up.

Switch OFF the connected

load. LED goes out.

Roller shutter/blind operation

Output is in stand-

by, status LED of

the button (6) is off.

Movement operation starts.

Status LED of the button (6)

lights up.

If the roller shutter/blind

is in nal position, the

button opposite must

be pressed to move the

shutter/blind.

Output active,

status LED of the

button (6) lights

up.

Movement operation stops,

LED goes out.

Table 1: Manual operation



























may get damaged in the connection









-



Final position switches could fuse

together. Motors, hangings and the



Only connect one motor per





Observe temperature range. Provide sufcient

cooling.

zMount device onto DIN rail in accordance with

DIN EN 60715.

Connect device

auto 1

auto 2

C1/C9 C3/ C11 C5/C13 C7 /C15

C2/C10 C4/ C12 C6/C14 C8/C1 6

Fig 2: Device connection

zConnect bus cable via connecting terminal (2).

Connecting loads to be switched

The output is congured as switching output.

zConnect load to the outputs of the device ac-

cording to gure (gure 2).

Connecting blind drives

The two adjacent relay outputs / /C1 , C3 C4, ..

each form a blind output for blind drives. Each left

relay output , , , is designated for the UP C1 C3 C5 ..

direction, and each right relay output , ,  C4 C6 ..

is designated for the DOWN direction. In manual

operation, the blind is moved UP and DOWN using

the corresponding operation buttons.

Two outputs are congured as blind output.

zConnect drives according to gure (gure 2).

While doing so, use the same phase (external

conductors).

Start-up



application software

The switch for manual operation (1) is in position

.

zSwitch on bus voltage.

zPress programming button (5).

The button lights up.

If the button does not light up, no bus voltage is

present.

zLoad the physical address into the device.

Status LED of the button goes out.

zLoad application software.

zNote down the physical address on the labelling

eld (4).



Information on the system conguration can be

taken from the extensive description of the service

module easylink.

Start up the device.

zSwitch on mains voltage on the outputs.



time

In blind/roller shutter operation, the operation time

for positioning the sunshade is important. The posi-

tion is calculated based on the operation time. The

slat adjusting time for slat blinds, determined by

the design, is part of the total operation time. The

opening angle of the slats is therefore set as oper-

ation time between opened and closed position.

The operation time for UP is normally longer

than the operation time for DOWN and must be

measured separately if necessary

zMeasure UP and DOWN operation time of the

hanging.

zMeasure slat adjusting time between OPEN

and CLOSED.

zEnter measured values into the parameter

setting – ... or .running time slat step time

Functional test

The functionality of the outputs is displayed via the

status LED of the operation button (6).

1 auto 1 / displays the status of the outputs

C1 C8 C1 C10 .. (16gang) resp. .. (20gang).

 / displays the status of the outputs

C9 C16 .. (16gang) resp. C11 ..  (20gang).

Produkt Specifikationer

Mærke:	Hager
Kategori:	Skifte
Model:	TXM616D

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager TXM616D stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte Hager Manualer

3 April 2025

3 April 2025

31 Marts 2025

31 Marts 2025

31 Marts 2025

31 Marts 2025

31 Marts 2025

6 Februar 2025

6 Februar 2025

1 Januar 2025

Skifte Manualer

Nyeste Skifte Manualer

Lancom GS-2412 Manual

4 April 2025

Lancom GS-2412P Manual

4 April 2025

Lancom GS-2426 Manual

4 April 2025

Roline 14.01.3579 Manual

2 April 2025

Fantini Cosmi B12BN Manual

1 April 2025

Fantini Cosmi B12DN Manual

1 April 2025

Fantini Cosmi B12GN Manual

1 April 2025

Fantini Cosmi B12HN Manual

1 April 2025

Crestron CLW-LSWEX-2GD Manual

1 April 2025

Vimar 30181.120 Manual

1 April 2025