Hager TYF642F Manual


Læs gratis den danske manual til Hager TYF642F (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Hager TYF642F, eller vil du spørge andre brugere om produktet?

Side 1/6
Device layout (Fig. 1)
TYF642F
A1 A2 A3 A4 A5 A6 A7 A8
ALL OFF
ON / OFF /
L N
30V s
A1-A8 µ 10A 1 230VAC
230-240V
TP / S
A1 A2 A3 A4
A5 A6 A7 A8
1 Keypad for manual control
2 Programming LED
3 Programming button
4 KNX connection
5 Mains supply connection
6 Status LED outputs
7 Connexion of fan coil unit.
Operation
Controls (Fig. 2)
TYF642F
A1 A2 A3 A4 A5 A6 A7 A8
ALL OFF
ON / OFF /
L N
TP / S
6 status LED outputs
8 key : manual control
9 LED : permanent manual control
indicator
A key ON / 3 : switching on
Z LED ON / : on, manual control3
E key OFF / : switching o 4
R LED OFF / : o , manual control4
T key ALL OFF: all outputs are o
Status indication
The status LEDs indicate the output states.A1...A8
LED o output is o
LED on output is on
LED ashing
slowly
output in manual control
mode
LED ashing
fast
output disabled by
permanent manual control
mode
Modes of operation
Bus operation operation via touch sensors
or other bus devices
Temporary
manual control
manual operation locally with
keypad, automatic return to
bus operation
Permanent
manual control
mode
only manual operation locally
on device
HBus operation in manual control mode
disabled.
Manual operation in the event of bus failure
enabled.
After failure and return of bus voltage, the
device switches over to bus operation.
After failure and return of mains voltage, the
device switches over to bus operation.
Manual control mode can be disabled in
operation via bus telegram.
Activating the temporary manual control mode
Keypad operation has been programmed
beforehand and is not disabled.
- Press the key.
LED A1 ashing, LED remains o .
H After 5 s without key-press, the actuator
returns automatically to the bus mode.
Deactivating the temporary manual control
mode
The device must be in the temporary manual
control mode.
- No key-press for 5 s.
or
- press the key repeatedly until the actuator quits
the temporary manual control mode.
LEDs A1...A8 are no longer ashing, but indicating
the output status.
Heating/cooling outputs : on deactivation of the
manual mode, the outputs switch into the position
then active, e.g. forced control (depending on
programming).
Fan outputs : on deactivation of the manual mode,
Safety instructions
Function
System information
This device is a product of the KNX system and
complies with KNX directives. Detailed technical
knowledge obtained in KNX training courses is a
prerequisite to proper understanding.
The functionality of this device depends on the
software. Detailed information on loadable software
and attainable functionality as well as the software
itself can be obtained from the manufacturer‘s
product database.
Planning, installation and commissioning of
the unit is e ected by means of KNX-certifi ed
software. The full functionality is available with
KNX commissioning software from version ETS3.0f
onwards.
The product database, technical descriptions,
conversion programs and other utilities are
available in their latest version on our Internet page.
Designated use
• Switching of electrical fan coil units
Switching of electrical AC 230 V consumers, e.g.
fans
Mounting on DIN rail in xed installations (power
distributions or small boxes).
Product features
Connection of a fan coil unit with up to 6 fan
stages or connection of fan coil units with up to 3
fan stages respectively
Manual output control, provisional operation
Control options for heating, cooling or combined
heating/cooling operation
• 2-pipe or 4-pipe operation
Individual or hierarchical switching of fan stages
• Feedback
• Output state indication
• Disable function for each channel
A1 A2 A3 A4
A5 A6 A7 A8
TYF642F
A1 A2 A3 A4 A5 A6 A7 A8
ALL OFF
ON
/OFF
/
LN
30V s
A1-A8 µ 10 A AC1 230 V
230-240V
TP / S
:.,nB
tebis
zDual fan coil actuator
rActuador de ventilo-convectores,
2 canales
6LE004143A
1 6LE004143A
qElectrical equipment must be installed
and fi tted by qualifi ed electricians
only. Observe the current accident
prevention regulations.
Failure to observe the instructions may
cause damage to the device
and result in re or other hazards.
The device is not suited for safe
disconnection of the mains supply.
Do not connect consumers
for SELV / PELV voltages.
Do not connect three-phase AC
motors.
These operating instructions are part
of the product and must be left with
the fi nal customer.
TYF642F


Produkt Specifikationer

Mærke: Hager
Kategori: Ikke kategoriseret
Model: TYF642F

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager TYF642F stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Hager Manualer

Hager

Hager WXF228 Manual

10 August 2025
Hager

Hager UKM340480 Manual

10 August 2025
Hager

Hager TRC301B Manual

10 August 2025
Hager

Hager GS20109011 Manual

10 August 2025
Hager

Hager AKB42000402 Manual

10 August 2025
Hager

Hager WXT312 Manual

10 August 2025
Hager

Hager BKSAN065110 Manual

10 August 2025
Hager

Hager VR10127011 Manual

10 August 2025
Hager

Hager UKM240280 Manual

10 August 2025
Hager

Hager ESR3336029 Manual

10 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone

Waterstone 7800 Manual

11 December 2025
Kwikset

Kwikset 258 Manual

11 December 2025
Schlage

Schlage F170 Manual

11 December 2025
Moen

Moen Align 7565EV Manual

11 December 2025
ALNO

ALNO MC10244 Manual

11 December 2025
JET

JET TAK-ZX Manual

11 December 2025
Waterstone

Waterstone 1455 Manual

11 December 2025
Laica

Laica NE2015 Manual

11 December 2025