Hager VM11214SPD Manual

Hager Skifte VM11214SPD

Læs gratis den danske manual til Hager VM11214SPD (3 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Hager VM11214SPD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Hager Ltd. Hortonwood 50, Hortonwood, Telford, TF1 7FT / 01952 675 675 1

Consumer nit U

Design 30 Switch

Disconnector Incomer

with SPD

For the distribution of power in a residential

application, conforming to BS EN 61439-3

including Annex ZB (16kA rating).

Design 30 is the enhanced board for use in applications where the

consumer unit is located in a living area of the dwelling.

The range of consumer units with a 100A rated current (InA) have

been designed for installations where the upstream overcurrent

protection device (OCPD) is rated at 100A or below.

Design 0 consumer unit is an ntry level board esigned or all 1 e d f

applications and allows compliance with S 7671:2018; B

Regulation 21.1.201 within domestics (household) applications consumer 4

units and similar assemblies shall comply with S EN 61439-3 and hall B s

have their enclosure manufactured rom a on-combustible material. f n

Regulation 11.3.3 additional protection y means of a 0mA RCD s 4 b 3 i

provided y RCBOs. b

Regulation 14.1&2 segregation f circuits to avoid anger and minimise 3 o d

inconvenience in he event of a ault. t f

Regulation 22.6.202 protection f wiring concealed n walls or partitions. 5 o i

Regulation 31.3.3 Selection f appropriate RCD. Type A CBOs can 5 o R

d t petect and respond o both AC and ulsating DC components.

Regulation 36.4.3.2 & 36.4.202 overload protection f switches and 5 5 o

R iCCBs. For installations where the upstream overcurrent protection s less

than r equal to 100 A. o

Regulation 443.4 Protection st transient over voltages, provided by again

factory fitted type 2 SPD.

Description

Size Cat ref.

Cat ref.

with Knockouts

8 Way 100A Switch Disconnector Incomer with Factory Fitted SPD 4 VM108SPD VM108KSPD

12 Way 100A Switch Disconnector Incomer with Factory Fitted SPD 5 VM112SPD VM112KSPD

18 Way 100A Switch Disconnector Incomer with Factory Fitted SPD 7 VM118SPD VM118KSPD

8 + 10 Way Dual Row 100A Switch Disconnector Incomer with Factory Fitted SPD 4(2) VM10810SPD VM10810KSPD

12 +14 Way Dual Row 100A Switch Disconnector Incomer with Factory Fitted SPD 5(2) VM11214SPD VM11214KSPD

16 + 20 Way Dual Row 100A Switch Disconnector Incomer with Factory Fitted SPD 7(2) VM11820SPD VM11820KSPD

VM108SPD

Features & Beneﬁts

- Cable clamp - Secures supply cables on entry to main incoming

device preventing any movement being transmitted through metertails

to device

- Square cable entry points top and bottom for use with cable trunking

(references available with or without knockouts)

- Rear Knockouts for ease of cable entry – Cable protector plate

provided

- Rigid top wall – Enhances rigidity to prevent distortion when removing

knockouts

- Locate and hold cover - allows use of both hands whilst xing cover

- Front cover retained screws – Prevents loss during installation

- Full metal DIN rail – Secure and stable attachment of devices

- Quick release clip on MCB/RCBO – Allows removal of MCB/RCBO

with busbar still in place

- Optimised cabling space – DIN rail position allows maximum cabling

space

- Top mounted terminal rail makes the wiring of the neutral and earth

connections neat and simple.

- Health and Safety lock allows the door to be secured with circuits

isolated during construction (via accessory, see overleaf).

- Torque settings displayed inside front cover so they’re easily

accessible by the electrician.

- Lockable front door via an accessory (see overleaf).

Fa fitte type surge protectionctory d 2

Design 0 3

Switch isconnector ncomer onsumer nit D I C U with SPD

Hager Ltd. Hortonwood 50, Hortonwood, Telford, TF1 7FT / 01952 675 675 2

Technical Characteristics

Standards BS EN 61439-3

Classication Consumer Unit

Rated & Operational Voltage (Un/Ue) 230V a.c 50 Hz

Rated Insulation Voltage (Ui) 320V a.c. 50Hz

Rated Frequency (fn) 50 Hz

Rated impulse withstand voltage (Uimp) 4kV

Rated Current of the Assembly (Ina) 63A/100A

Rated Current of an Outgoing Circuit I

nC RCBO A1**G- A - 45A (Marked Rated Current on Device) AD 40

RCBO - 6A - 32A (Marked Rated Current on Device)ADA3**G

Rated Conditional Short Circuit of the Assembly (I

cc) Annex ZB: 16kA rms at 250V, power factor 0.6 with equipment and arrange-

ments specied in Hager's technical documentation/catalogue

Protection against electric shock Consumer Unit shall be installed in an electrical system conforming to IEC

60364 / BS 7671

Rated Diversity Factor (RDF) / Values of assumed loading 2 Way to 3 Way - 0.8, 4 Way to 5 Way - 0.7, 6 Way to 9 Way - 0.6, 10 Way and

above - 0.5

Note: RDF only applies to continuously and simultaneously loaded circuits.

In principle, this means adjacent circuit breakers having a load on time exceeding 30 minutes or where a load not exceeding 30 minutes has an 'off' time less than

the 'on' time will need to have the rated diversity factor applied as indicated.

Pollution Degree 2

Types of System Earthing for which the assembly is designed TNC-S and TN-S when installed in an electrical system conforming to BS 7671TT,

Intended locations Indoor use only

Stationary assembly

Degree of protection IP2XC with door open / closed and full compliment of devices / blanks tted.

Note: Where cables are installed through the top wall of the enclosure, gaps of

IP4X to be maintained.

Intended use Intended for use in domestic (residential) or similar premises

Electromagnetic compatibility (EMC) classication EMC environment B

External design Wall mounted, surface type, enclosed assembly.

Mechanical impact protection IK05

Type of construction Fixed parts

Incoming Line/Neutral terminal (80 - 100A board) 50mm²

Incoming Line/Neutral terminal (63A board) 25mm²

Incoming Earth Terminal 16mm²

Warranty - Hager undertakes to replace or repair at its discretion products should they become inoperable within the time periods as stated. - 2 Years

Height

Width

Depth

Design 30 Dimensions (mm)

Enclosure Size

4 5 7

Height 240 240 240

Width 293 364 472

Depth 102.5 102.5 102.5

Number of Knockouts

*Top Face 30 x 25 (mm) 2 2 2

*Top Face 40 x 30 (mm) 44 6

Back 100 x 50 (mm) 13 3

*Bottom Face 30 x 25 (mm) 44 5

Accessories

Cable protector plate Provides protection for cables entering from the rear of the board VM02CE

Health and safety lock Provides the ability to lock the consumer unit during the installation process VMHBL

Design 30 door locking kit Allows the board to be lockable VMLOCK

Grommet strip For protecting cables against damage when entering the board VM05GS

Rear stand off plates To stand consumer unit off wall allowing surface mounted cables to enter through rear of unit. VM01SP

Devices

Single Pole, Single Mod RCBO 6kA, 40A - 45A Type A ADA1**G

Single Pole, Single Mod Reduced Height RCBO 6kA, 6A - 32A Type A ADA3**G

* References with a ‘K’ sufx feature top and bottom square knockouts.

Design 0 3

Switch isconnector ncomer onsumer nit D I C U

with SPD

Produkt Specifikationer

Mærke:	Hager
Kategori:	Skifte
Model:	VM11214SPD
Kode for international beskyttelse (IP):	IP2XC
Bredde:	364 mm
Dybde:	102.5 mm
Højde:	480 mm
Husmateriale:	Stål
Monteringstype:	Overflade