Hager VM112KSPD Manual

Hager Ikke kategoriseret VM112KSPD

Læs gratis den danske manual til Hager VM112KSPD (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Hager VM112KSPD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Design 10 / 30 Consumer Unit

Instructions/Data Sheet

This Consumer Unit and Hager devices conform with the following standards:

Consumer Unit: BS EN 61439-3 including Annex ZB.

Switch-disconnectors: BS EN 60947-3.

Residual Current Circuit Breaker (RCCB): BS EN 61008-1

Residual current operated circuit breaker with integral overload (RCBO): BS

EN 61009-1

Miniature Circuit Breaker (MCB): BS EN 60898-1

Arc Fault Detection Devices: BS EN 60626

Surge Protection Devices: BS EN 61643

Installation Instructions:

All product(s) must be installed by a suitably competent electrician

Giving consideration to their intended use and in accordance with the current

edition of BS 7671 (IET Wiring Regulations).

The Electricity at Work regulations and the Health and Safety at Work Act shall be

complied with.

Only equipment and arrangements specied in Hager’s technical documentation /

catalogue shall be used.

Install in the horizontal plane only.

For guidance when making connections in a consumer unit electrical safety rst /

BEAMA document “Guidance for installers when making connections in consumer

units” is available from hager.co.uk/63026.htm

Important notice:

To prevent potential overheating from loose connections the installer shall check

connections are tight to the torque levels stated in these instructions prior to

energizing this board. This check should include factory made connections which

may have loosened in transit.

Good workmanship and proper materials must be applied by the installer. The cable

entry method shall, as far as reasonably practical, maintain the non-combustable

arrangement of the enclosure. Account shall be taken of these instructions.

For guidance on RCD selection, AFDD selection and more, see the related BEAMA

guide in our BEAMA guide web page - hager.co.uk/18thedition.

The units have multiple xing points that will suit No.8 & No.10 screws

These metal units are provided with knockouts suitable

for use with 100x50mm trunking, 50x50mm trunking

and also large rear knockouts.

Rear cable entries shall enter thorough selected rear Knockout; once

the Knockout is removed apply the appropriate cable entry plate (full

list on page 4). Cable entry plates are available to clip into the knockout

hole and provide a safe edge to bring cables in.

Note: Only BASEC approved cable should be used 1.0mm

2 to 16mm2 for

outgoing cables

Up to 35.0mm2 for incoming live cables. Single conductors below 1.5mm² need

to be doubled back in the terminal bar.

Cable entry facilities:

Wall Fixing:

Use circuit as

normal

* Important note: Fuse carriers must not be opened or closed with the

main switch in the ON position.

YES

RCCB

AFDD

NO YES

YES

Does device

stay ON?

Does device

stay ON?

Does device

stay ON?

Does device

supply socket

outlets

Call an

electrician

Unplug all

appliances from

circuit and reset

device

Plug in & switch on

appliances one at a time

until device trips / blows,

identifying faulty appliance

Unplug faulty

appliance until

repaired. Reset device.

Other appliance may

be used

Try & reset device once

Please refer to

additional leaet

included with the

consumer unit.

Device Tripped

MCB

or RCBO

START

What device

is it?

Try & reset device once

Use circuit as

normal

Turn OFF

all MCB / fuse*

devices

Call an

electrician

Reset RCCB

Does device

stay ON?

Turn ON MCB / fuse*

devices one at a time

until RCCB trups again,

identifying faulty circuit

Design 30

Dimensions (mm)

Enclosure Size

234567

Height 240 240 240 240 240 240

Width 149 221 293 364 400 472

Depth 102.5 102.5 102.5 102.5 102.5 102.5

Number of Knockouts

Top Face 30 x 25 2 2 2 2 2 2

Top Face 40 x 30 0 2 4 4 6 6

Back 100 x 50 1 1 1 3 3 3

Bottom Face 30 x 25 2 3 4 4 5 5

Design 10

Dimensions (mm)

Enclosure Size

234567

Height 246 246 246 246 246 246

Width 155 227 299 370 406 478

Depth 1 83 83 83 83 83 83

Depth 2 100 100 100 100 100 100

Boards with Square

Knockouts Number of Knockouts

Top Face 30 x 25 2 2 2 2 2 2

Top Face 40 x 30 0 2 4 4 6 6

Back 100 x 50 1 1 1 3 3 3

Bottom Face 30 x 25 2 3 4 4 5 5

Height

Width

Depth 2

Depth 1

Height

Width

Depth

Accessories Comparison

Surface Mounted Consumer Units

Feature Description

Design

Meter tail entry

plate

( )VM04CE

When clipped into place, the moulding holes

allows meter tails and CPC to enter the

board safely

Top wall cable

entry plates

( )VM03CE

Specially designed for our square

knockouts, these plates provide more

options for cable entry. When used with

50x50mm trunking, IP ratings can be

achieved.

Blind cable

entry plates

(VM04CB,

VM03CB)

A blank plate for drilling which allows

the installer to decide on the method of

incoming cables - compression gland etc.

Rear cable

entry plate

( )VM02CE

Allows cables to enter the rear of the board

without the risk of damage from sharp

edges.

Cable clamp

(VA10MT)

Incoming meter tails can be safely secured,

eliminating stress within the switch terminal.

Stand-off plate

( )VM01SP

Provides 12mm of clearance at the rear of

the consumer unit to allow surface mounted

cables to enter the board from the rear.

  Included with board Available as an accessory

* Knockouts available by choice on Design 30 range. References ending with a ‘K’

contain knockouts.

Design 10 Dual Row

Dimensions (mm)

Enclosure Size

3 (2) 4 (2) 5 (2) 6 (2) 7 (2)

486 486 486 486 486

227 299 370 406 478

83 83 83 83 83

100 100 100 100 100

Number of Knockouts

22222

24466

22666

34455

Design 30 Dual Row

Dimensions (mm)

Enclosure Size

3 (2) 4 (2) 5 (2) 6 (2) 7 (2)

480 480 480 480 480

221 293 364 400 472

102.5 102.5 102.5 102.5 102.5

Number of Knockouts

22222

24466

22666

34455

ZD0820 - Issue 6

ZD0820

ZD0820 - Issue 6

Design 10 / 30 Consumer Unit

Installation Instructions / Data Sheet

Design 10 / 30 Consumer Unit

Installation Instructions / Data Sheet

Produkt Specifikationer

Mærke:	Hager
Kategori:	Ikke kategoriseret
Model:	VM112KSPD
Kode for international beskyttelse (IP):	IP2XC
Bredde:	364 mm
Dybde:	102.5 mm
Højde:	240 mm
Husmateriale:	Stål
Monteringstype:	Overflade