Hager VML90810H Manual

Hager Ikke kategoriseret VML90810H

Læs gratis den danske manual til Hager VML90810H (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Hager VML90810H, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
Design 10 / 30 Consumer Unit
Instructions/Data Sheet
This Consumer Unit and Hager devices conform with the following standards:
Consumer Unit: BS EN 61439-3 including Annex ZB.
Switch-disconnectors: BS EN 60947-3.
Residual Current Circuit Breaker (RCCB): BS EN 61008-1
Residual current operated circuit breaker with integral overload (RCBO): BS
EN 61009-1
Miniature Circuit Breaker (MCB): BS EN 60898-1
Arc Fault Detection Devices: BS EN 60626
Surge Protection Devices: BS EN 61643
Installation Instructions:
All product(s) must be installed by a suitably competent electrician
Giving consideration to their intended use and in accordance with the current
edition of BS 7671 (IET Wiring Regulations).
The Electricity at Work regulations and the Health and Safety at Work Act shall be
complied with.
Only equipment and arrangements specied in Hager’s technical documentation /
catalogue shall be used.
Install in the horizontal plane only.
For guidance when making connections in a consumer unit electrical safety rst /
BEAMA document “Guidance for installers when making connections in consumer
units” is available from hager.co.uk/63026.htm
Important notice:
To prevent potential overheating from loose connections the installer shall check
connections are tight to the torque levels stated in these instructions prior to
energizing this board. This check should include factory made connections which
may have loosened in transit.
Good workmanship and proper materials must be applied by the installer. The cable
entry method shall, as far as reasonably practical, maintain the non-combustable
arrangement of the enclosure. Account shall be taken of these instructions.
For guidance on RCD selection, AFDD selection and more, see the related BEAMA
guide in our BEAMA guide web page - hager.co.uk/18thedition.
The units have multiple xing points that will suit No.8 & No.10 screws
These metal units are provided with knockouts suitable
for use with 100x50mm trunking, 50x50mm trunking
and also large rear knockouts.
Rear cable entries shall enter thorough selected rear Knockout; once
the Knockout is removed apply the appropriate cable entry plate (full
list on page 4). Cable entry plates are available to clip into the knockout
hole and provide a safe edge to bring cables in.
Note: Only BASEC approved cable should be used 1.0mm
2 to 16mm2 for
outgoing cables
Up to 35.0mm2 for incoming live cables. Single conductors below 1.5mm² need
to be doubled back in the terminal bar.
Cable entry facilities:
Wall Fixing:
Use circuit as
normal
* Important note: Fuse carriers must not be opened or closed with the
main switch in the ON position.
YES
YES
YES
RCCB
AFDD
NO
NO
NO
NO
NO YES
YES
Does device
stay ON?
Does device
stay ON?
Does device
stay ON?
Does device
supply socket
outlets
Call an
electrician
Unplug all
appliances from
circuit and reset
device
Plug in & switch on
appliances one at a time
until device trips / blows,
identifying faulty appliance
Unplug faulty
appliance until
repaired. Reset device.
Other appliance may
be used
Try & reset device once
Please refer to
additional leaet
included with the
consumer unit.
Device Tripped
MCB
or RCBO
START
What device
is it?
Try & reset device once
Use circuit as
normal
Turn OFF
all MCB / fuse*
devices
Call an
electrician
Reset RCCB
Does device
stay ON?
Turn ON MCB / fuse*
devices one at a time
until RCCB trups again,
identifying faulty circuit
Design 30
Dimensions (mm)
Enclosure Size
234567
Height 240 240 240 240 240 240
Width 149 221 293 364 400 472
Depth 102.5 102.5 102.5 102.5 102.5 102.5
Number of Knockouts
Top Face 30 x 25 2 2 2 2 2 2
Top Face 40 x 30 0 2 4 4 6 6
Back 100 x 50 1 1 1 3 3 3
Bottom Face 30 x 25 2 3 4 4 5 5
Design 10
Dimensions (mm)
Enclosure Size
234567
Height 246 246 246 246 246 246
Width 155 227 299 370 406 478
Depth 1 83 83 83 83 83 83
Depth 2 100 100 100 100 100 100
Boards with Square
Knockouts Number of Knockouts
Top Face 30 x 25 2 2 2 2 2 2
Top Face 40 x 30 0 2 4 4 6 6
Back 100 x 50 1 1 1 3 3 3
Bottom Face 30 x 25 2 3 4 4 5 5
Height
Width
Depth 2
Depth 1
Height
Width
Depth
Accessories Comparison
Surface Mounted Consumer Units
Feature Description
Design
10
Design
30
Meter tail entry
plate
( )VM04CE
When clipped into place, the moulding holes
allows meter tails and CPC to enter the
board safely
Top wall cable
entry plates
( )VM03CE
Specially designed for our square
knockouts, these plates provide more
options for cable entry. When used with
50x50mm trunking, IP ratings can be
achieved.
Blind cable
entry plates
(VM04CB,
VM03CB)
A blank plate for drilling which allows
the installer to decide on the method of
incoming cables - compression gland etc.
Rear cable
entry plate
( )VM02CE
Allows cables to enter the rear of the board
without the risk of damage from sharp
edges.
Cable clamp
(VA10MT)
Incoming meter tails can be safely secured,
eliminating stress within the switch terminal.
Stand-off plate
( )VM01SP
Provides 12mm of clearance at the rear of
the consumer unit to allow surface mounted
cables to enter the board from the rear.
  Included with board Available as an accessory
* Knockouts available by choice on Design 30 range. References ending with a ‘K’
contain knockouts.
Design 10 Dual Row
Dimensions (mm)
Enclosure Size
3 (2) 4 (2) 5 (2) 6 (2) 7 (2)
486 486 486 486 486
227 299 370 406 478
83 83 83 83 83
100 100 100 100 100
Number of Knockouts
22222
24466
22666
34455
Design 30 Dual Row
Dimensions (mm)
Enclosure Size
3 (2) 4 (2) 5 (2) 6 (2) 7 (2)
480 480 480 480 480
221 293 364 400 472
102.5 102.5 102.5 102.5 102.5
Number of Knockouts
22222
24466
22666
34455
2
ZD0820 - Issue 6
ZD0820
ZD0820
ZD0820
ZD0820
1
ZD0820 - Issue 6
GB
Design 10 / 30 Consumer Unit
Installation Instructions / Data Sheet
Design 10 / 30 Consumer Unit
Installation Instructions / Data Sheet

Produkt Specifikationer

Mærke: Hager
Kategori: Ikke kategoriseret
Model: VML90810H

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager VML90810H stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Hager Manualer

Hager

Hager WXF228 Manual

10 August 2025
Hager

Hager UKM340480 Manual

10 August 2025
Hager

Hager TRC301B Manual

10 August 2025
Hager

Hager GS20109011 Manual

10 August 2025
Hager

Hager AKB42000402 Manual

10 August 2025
Hager

Hager WXT312 Manual

10 August 2025
Hager

Hager BKSAN065110 Manual

10 August 2025
Hager

Hager VR10127011 Manual

10 August 2025
Hager

Hager UKM240280 Manual

10 August 2025
Hager

Hager ESR3336029 Manual

10 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone

Waterstone 7800 Manual

11 December 2025
Kwikset

Kwikset 258 Manual

11 December 2025
Schlage

Schlage F170 Manual

11 December 2025
Moen

Moen Align 7565EV Manual

11 December 2025
Energy Sistem

Energy Sistem ESG M3 Neon Manual

11 December 2025
ALNO

ALNO MC10244 Manual

11 December 2025
JET

JET TAK-ZX Manual

11 December 2025
Crosley

Crosley Nashville CF1165 Manual

11 December 2025
Waterstone

Waterstone 1455 Manual

11 December 2025
Laica

Laica NE2015 Manual

11 December 2025