Hager XEM510 Manual

Hager Skifte XEM510

Læs gratis den danske manual til Hager XEM510 (2 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Hager XEM510, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Interfaces LAN (10/100 Mbit)

RS485 (half-duplex,

max. 115200 baud)

Protection class ll

Overvoltage category III

IP IP2X

Connection cross

section in line with

EN 60204

10-25 mm² *

* Mechanical: 1.5-25 mm

(e.g. for connecting

external current

transformers)

Tightening torque

for screw terminals

2.0Nm

Weight 0.3 kg

Dimensions 88 x 70 x 65mm

Ambient temperature

in operation (direct

measurement)

With reduced measuring

current IN < 32 A (direct

measurement)

-25 °C…+45 °C

-25 °C…+55 °C

Ambient temperature

during transportation /

storage

-25 °C…+70 °C

Relative humidity (non-

condensing)

Up to 75% as an

annual average,

up to 95% on up

to 30 days/year

Max. altitude during

operation

2000 m above sea

level

Degree of polution 2

Usage Indoor use only or in a

waterproof enclosure

Mains power supply

Starting current < 25mA

Supply voltage /

frequency

110 V ~ ±10 % /

60 Hz ± 5%

230 V ~ ±10 % /

50 Hz ± 5%

Internal consumption

max

5.0 W

Measuring current circuit

for measurement category lll

Limit current I

/ phase 63A

Rated voltage max. 230/400 V ~

Frequency range 50/60 Hz ± 5%

A Outer conductors, L1, L2, L3 outputs

B(A) RS485 modbus RTU connection

B(B) Not used

C Connection Ethernet LAN1 (switch mode)

D Connection Ethernet LAN2 (switch mode)

E PWR: Power LED

F APP: Application LED

G NET: Network LED

H BTN: Button (reset)

I Outer conductors, L1, L2, L3 Inputs

J Neutral conductor N

7. Modbus interface

Note the following points when connecting

external devices to the RS485 Modbus RTU

interface of the Local Load Manager.

Controller:

Requirement for the cable:

• Nominal voltage/wire insulation:

300V RMS

• Cable cross section: 0.25 ... 1.5mm²

• Cable type: Rigid or ﬂ exible

• Recommendation: Use AlphaWire standard

cable, designation 2466C. Alternatively, a

CAT5e cable can also be used.

Requirement for cable installation:

• In the area for connecting the RS485

Modbus RTU interface on the Local Load

Manager, mechanical means must be

provided to ensure that individual wires of

the connecting cable are at least 10mm

away from live parts.

• The connecting cable must be run

separately from the mains cables in the

distribution board and on the permanent

link.

• The RS485 Modbus RTU interface of the

connected unit must meet the safety extra

low voltage requirements.

Power LED

Colour Status Description

Green Flashing Device is starting.

Green On Application launched correctly and running.

Orange Flashing Application on update. Try to realize an hardware reboot.

Orange On Application not launched: an issue appears in application lifecyc le. Try to

realize an hardware reboot. If system doesn’t go back to normal, please

take contact with hager support.

Red On Application / System Dead: Try to realize an hardware reboot. If system

doesn’t go back to normal, please take contact with hager support.

Application LED

Colour Status Description

Green On Installation is running.

Orange On Product not fully conﬁ gured.

Red On Critical error occur, see hager website https://hgr.io/r/XEM520 or https://

hgr.io/r/XEM510

Orange Flashing rapidly Date and time are not synchronizing, connect to the webserver in order to

solve the issue.

Network LED

Colour Status Description

/ Off No connection.

Green On Internet connected.

Green Flashing rapidly Admin password set to default during 10 min (press between 2 and 4

seconds).

Orange On No internet connection.

Red On Network issue: conﬂ ict on IP, no address got from DHCP server…

XEM520

Danger of death by electric shock.

Live components carry potentially fatal

voltages.

• Before starting any installation or

maintenance work, switch off the power to

the distribution board and secure to prevent it

being switched on again accidentally.

• Make sure that the conductors to be

connected to the meter are voltage-free.

• All installation and maintenance work on this

unit must be carried out by a trained and

authorised electrician.

The Local Load Manager is supplied with

power via outer conductor L1. At least the

outer conductor L1 and neutral conductor N

need to be connected for the unit to switch on.

1. Introduction

This product makes it possible to manage a

cluster of charging stations for electric cars.

It is able to adapt the charging power

of electric vehicles according to the

consumption of the building (dynamic

management) or according to a ﬁ xed value

(static management). It avoids an electrical

shutdown of the building due to an overload.

The product is also able to manage access

to the charging station by conﬁ guring RFID

badges and manage di erent charging modes.

An „open“ access is accessible for the

end user, in order to check in real time the

availability of the terminals.

2. Documentation

The latest and complete documentation

is available on https://hgr.io/r/XEM510 or

https://hgr.io/r/XEM520

3. Safety instructions

4. Technical data

5. Operation of the Local Load

Manager at ambient temperature

of 55°C

The Local Load Manager must not be run

continuously at ambient temperatures of 55

°C. If such condition can be present, please

consider the usage of Current Transformer

and to install the Local Load Manager in an

appropriate environment.

8. Led statuses

6. Product description

Avoid damage to or destruction of the Local

Load Manager

• Do not connect an ISDN cable to the Local

Load Manager’s network connection.

• Damage to or destruction of the Local

Load Manager by voltage surges on the

network cable.

• If network cables are installed outside the

building, voltage surges can be caused by

lightning strike, for example.

• If installed outside the building, the network

cable must be protected with suitable

overvoltage protection.

• Damage to or destruction of the Local

Load Manager by improper use.

• Do not operate the Local Load Manager

outside the specified technical tolerances.

• The LAN1/2 Ethernet interface of the

connected unit must meet the safety extra

low voltage requirements.

• For outdoor use, install an network isolator

on the LAN1/2 Ethernet input of the product.

Danger of death by electric shock.

• Live components carry potentially fatal

voltages.

• Only use the Local Load Manager in a dry

environment and keep it away from liquids.

• Install the Local Load Manager only in

approved enclosures or distribution boards

downstream of the electricity supply

company’s meter so that the connections for

the outer and neutral conductors are located

behind a cover or guard to prevent accidental

contact.

• Before starting any installation or

maintenance work, switch off the power to

the distribution board and secure to prevent it

being switched on again accidentally.

• Maintain the prescribed minimum distances

between the network cable and mains

voltage installation components or use

suitable insulation.

Danger of death by electric shock or fire Live

components carry potentially fatal voltages.

If the ambiant temperature exceed 45°C:

• Electrical protection must not exceed 32A.

• External current transformers should be used

for higher currents.

• The Local Load Manager must be connected

with cables that are at least 10mm² in cross

section and no less than 1m long.

Maximal modbus cable length = 10m.

Connection diagram for RS485 connector:

Pin Description Color

1 Not used

2 Com. / C/C’ / OVL Brown

3 D1 / B/B’ / (+) Green

4 D0 / A/A’ / (-) Yellow

Local Load Manager

6LE009017B

XEM510, XEM520

B(A)

XEM520

B(B)

HagerEnergy GmbH, Ursula-Flick-Straße 8, 49076 Osnabrück, Germany

Produkt Specifikationer

Mærke:	Hager
Kategori:	Skifte
Model:	XEM510

Har du brug for hjælp?

Hvis du har brug for hjælp til Hager XEM510 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte Hager Manualer

3 April 2025

3 April 2025

31 Marts 2025

31 Marts 2025

31 Marts 2025

31 Marts 2025

31 Marts 2025

6 Februar 2025

6 Februar 2025

1 Januar 2025

Skifte Manualer

Nyeste Skifte Manualer

Lancom GS-2412 Manual

4 April 2025

Lancom GS-2412P Manual

4 April 2025

Lancom GS-2426 Manual

4 April 2025

Roline 14.01.3579 Manual

2 April 2025

Fantini Cosmi B12BN Manual

1 April 2025

Fantini Cosmi B12DN Manual

1 April 2025

Fantini Cosmi B12GN Manual

1 April 2025

Fantini Cosmi B12HN Manual

1 April 2025

Crestron CLW-LSWEX-2GD Manual

1 April 2025

Vimar 30181.120 Manual

1 April 2025