Haier EI39G1M Manual

Haier Vandvarmer & kedel EI39G1M

Læs gratis den danske manual til Haier EI39G1M (2 sider) i kategorien Vandvarmer & kedel. Denne vejledning er vurderet som hjælpsom af 59 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 30 anmeldelser. Har du et spørgsmål om Haier EI39G1M, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1 2

Indicates the act that must be forbidden

Indicates the act that must be carried out

Indicates the matter which must be paid attention to

0040510390



EI39G1M(W)

EI39G1M(S)

Technical parameter

EI39G1M(W) EI39G1M(S)

IP25

M Pa

W-A

360

*200

*85

1 1 11 1

EI39G1M(W)

EI39G1M(S)

1.5L/min

0.02 PaM

0.6 PaM

AC 240 V

163（ｍｍ）

319(mm)

TB Terminal Block：

ER: ELCB Ring

RT2: Water-out Sensor

FL: Flow Sensor

MT: Thermal Cut-Out

HE: Heating Element

Control

Board

Display

Board

Triac Board

RT2

BROWN

BLUE

YELLOW&GREEN

BROWN

BLUE

YELLOW

&GREEN

BLACK

YELLOW

&GREEN

COM

3950-16.5

Instantaneous Water Heater

Operation Manual

Model：

Please read this manual carefully before use

Please keep this manual properly for reference. One dimensional code 60mm*10mm

(please read before use)

Our company will not bear any responsibility for incorrect installation and use of

this water heater!

Symbol interpretation

Caution

Note:

Failure to follow this manual means the risk of accident, property loss and personal injury.

The water heater must be repaired or maintained by qualified professional personnel.

Improper operation may cause serious personal injury or property loss.

In case of any abnormality or scorching smell of

the water heater, please cut off the power supply

immediately and contact the service center.

diameters meet the rated current of the water

hot water

This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

Children should be supervised to ensure that they do not

play with the appliance.

Caution

In order to ensure safety, the power supply of the water

heater should be reliably earthed, otherwise, it is strictly

prohibited to use the water heater. The test pencil should

be used to determine whether the live wire and the

neutral wire are connected reversely.

switch matched with the water heater must be used

Do not touch the power supply with wet hands, so as

to prevent it from getting wet by water. If it is wet by

accident, it must be inspected and confirmed by the

professional personnel appointed by our company

before reuse to prevent electric shock.

Make sure to use an independent power supply．

This appliance is not to be used for a potable water

supply.

Introduction to components

Inductor coil

Terminal block

Computer

board

Crimping

board

Flow sensor

Indicator

board

Water-out

pipe

Water-in pipe

Stainless

steel circlip

Water-out

temperature

Heating

element

Temperature

controller

sensor

heater

(Set) package

(Set)

Three-gear

sprinkler

(Set)

Electrical Schematic Diagram

Product specification

Model

Rated power-Rated

current

Rated Frequency

Waterproof Grade

Rated Pressure

Minimum inlet pressure

Maximum inlet pressure

Maximum water-out

temperature

Start flow

Outline dimension

Net weight

Note:The allowable error range of the net weight is ±10%.

Installation guide

Precautions for installation

1 The load-bearing wall for installing the water heater should be able to bear twice the weight of the water.

heater filled with water.

2.The water heater should be installed indoors and in a non-icing place, with pipes arranged centrally.The hot

water outlet should not be too far away from the hot water use point. If the distance exceeds 2m,the hot water

pipe should be insulated to reduce heat loss.

3.The water heater should be installed in a place that is convenient for use and maintenance and has a sewer

to ensure that surrounding or lower facilities cannot be damaged when water heater or water pipe leaks. Please

do not install the water heater in a place that can be sprayed directly or is prone to icing.

4. Because of the high power of this water heater, before installing the water heater, please carefully check

whether the ammeter and power wire diameters (2.5mm 2recommended) and fuse meet the rated current and

voltage requirements of this water heater. If necessary, please ask a professional electrician to check the circuit.

5. Do not connect the water-in and water-out pipes reversely; Under no circumstances should the outlet be

blocked.

6. To ensure safety, the water heater should use the standard single-phase bipolar air switch or circuit breaker

(in the case of circuit breaking, the open distance of all contacts should be at least 3mm so as to reliably cut off

the connection with the external power supply during maintenance), and be earthed reliably, with the earthing

resistance of the household earth wire less than 4Ω. Because the water heater requires a large current,the

incoming power supply of the water heater must be directly connected with the air switch, and the power plug

should not be used.

7. The test pencil should be used to determine whether the live wire and the neutral wire are connected

reversely.

8. The outlet must not be connected to any tap or fitting other than those specified.

9. The water heater is equipped with the flow control valve. For use safety, the flow control valve should be

installed on the water-in pipe, and it is strictly forbidden to install the valve at the outlet of the water heater.

10.The water inlet of this appliance shall not be connected to inlet water obtained from any other water heating

system.

11.Metallic / chromed hose and conductive control valve shall not be used!

2.Remove the power cord

plug of the rear shell.

Installation of whole machine

1.Remove the front shell

screws and the front shell.

3. Install the power cord corresponding to

the live wire, neutral wire and earth wire

respectively, and fix it by wire nail.

4. Confirm the installation position of the water heater, and drill four φ6X35mm holes on the load-bearing wall

with impact drill, with the spacing as shown in the figure below (it is also allowed to correspondingly locate

the four fixing points by placing the rear shell on the wall). And then, drive four expansion bolts into four holes

respectively, hang up the machine,and fix the machine with screws.

1.85kg

Produkt Specifikationer

Mærke:	Haier
Kategori:	Vandvarmer & kedel
Model:	EI39G1M

Har du brug for hjælp?

Hvis du har brug for hjælp til Haier EI39G1M stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vandvarmer & kedel Haier Manualer

Haier HP250M1-U1 Manual

8 November 2025

Haier ES80V-A3 Manual

29 September 2025

Haier P-J-F-2-120/1.90/0.80-P2(J) Manual

26 Juli 2025

Haier EC4002-Q6 Manual

26 Juli 2025

Haier EC8001-PD3(U1) Manual

28 Maj 2024

Haier ES60H-S5K(E) Manual

30 Marts 2024

Haier FCD-JTSA80-III Manual

14 Februar 2024

Haier EI39G1M Manual

22 Januar 2024

Haier ES25V-ED Manual

12 Januar 2024

Haier EC6003-YT3 Manual

26 December 2023

Vandvarmer & kedel Manualer

Nyeste Vandvarmer & kedel Manualer

EccoTemp ESH-4.0 Manual

4 December 2025

EccoTemp SH22i Manual

3 December 2025

EccoTemp EM-7.0 Manual

3 December 2025

EccoTemp 6GB Manual

3 December 2025

EccoTemp SH22 Manual

3 December 2025

Westinghouse ET011K Manual

27 November 2025

Vevor CW-3000 Manual

23 November 2025

Vevor FJI-POR-70S2 Manual

22 November 2025

Vevor FJI-POR-40S2 Manual

21 November 2025

Midea 787300 Manual

15 November 2025